AXLOC4M-150 - Uncategorized AXESS - Free user manual and instructions
Find the device manual for free AXLOC4M-150 AXESS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 4-Channel Line Output Converter |
| Dimensions (W x L x H) | 4.5 x 3.5 x 1.2 inches (11.4 x 8.9 x 3.0 cm) |
| Weight | 0.3 lbs (0.14 kg) |
| Power Supply | 12V DC (vehicle electrical system) |
| Input Type | Speaker-level (high-level) signals |
| Output Type | RCA line-level (low-level) signals |
| Channels | 4 |
| Max Input Power per Channel | 150W RMS (estimated) |
| Frequency Response | 20 Hz – 20 kHz ±0.5 dB |
| Signal-to-Noise Ratio | >100 dB |
| Total Harmonic Distortion | <0.01% |
| Adjustable Gain | Yes, per channel pair |
| Ground Isolation | Yes, eliminates alternator whine |
| Remote Turn-On | Via +12V remote wire |
| Installation Method | Inline with factory speaker wires |
| Operating Temperature | -20°C to 60°C (-4°F to 140°F) |
| Maintenance | Wipe with a dry, soft cloth; avoid liquids |
| Safety Cautions | Disconnect battery before installation; secure away from heat sources |
| Spare Parts | None user-serviceable; consult professional for repairs |
| Warranty | 1 year limited warranty |
Frequently Asked Questions - AXLOC4M-150 AXESS
How do I connect the AXLOC4M-150 to my factory stereo?
Connect the speaker-level input wires (left/right front and rear) to the corresponding speaker outputs of your factory stereo. Use the included harness or solder connections. Then, connect the RCA outputs to your aftermarket amplifier.
What is the maximum wattage this line output converter can handle?
The AXLOC4M-150 is designed to handle up to 150W RMS per channel on the speaker-level inputs. Exceeding this may cause damage.
How do I adjust the gain on the AXLOC4M-150?
Locate the small potentiometers labeled 'Gain' on the unit. Use a small flathead screwdriver to adjust them clockwise to increase gain, counterclockwise to decrease. Start with gain at minimum and slowly increase until the desired volume is achieved without distortion.
Can I use this converter with an amplified factory system?
Yes, but ensure the factory amplifier output does not exceed 150W per channel. The AXLOC4M-150 accepts high-level inputs from factory amplifiers. If the output is too high, use a load resistor to prevent damage.
Why do I hear alternator whine after installation?
Alternator whine is often caused by ground loops. The AXLOC4M-150 has ground isolation, but ensure all connections are secure and the converter is grounded to the same point as the amplifier. Use a ground loop isolator if the issue persists.
Does the AXLOC4M-150 require a remote turn-on wire?
Yes, connect the remote turn-on (REM) wire to a +12V switched source, such as the amplifier's remote turn-on output. This powers the converter when the stereo is on.
What is the frequency response of this line output converter?
The frequency response is 20 Hz to 20 kHz ±0.5 dB, which covers the full audible range and ensures accurate sound reproduction.
Can I use this converter for a subwoofer setup?
Yes, the AXLOC4M-150 is a 4-channel converter. You can combine channels (e.g., using Y-splitters) to feed a monoblock subwoofer amplifier, or use a dedicated pair for front/rear speakers.
Is the AXLOC4M-150 compatible with 8-ohm speakers?
Yes, it accepts speaker-level inputs from any impedance down to 4 ohms. 8-ohm speakers are fine and will not damage the converter.
What should I do if the output is distorted?
Check the gain setting – reduce it if set too high. Ensure the input signal is not clipped from the source. Verify that the converter is securely connected and not overheating. If distortion persists, test with a known good source.
User questions about AXLOC4M-150 AXESS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual AXLOC4M-150 - AXESS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AXLOC4M-150 by AXESS.
USER MANUAL AXLOC4M-150 AXESS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : AXESS
Model : AXLOC4M-150
Category : Uncategorized