Feature - Uncategorized Martin Logan - Free user manual and instructions
Find the device manual for free Feature Martin Logan in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Floor-standing loudspeaker |
| Brand | Martin Logan |
| Model | Feature |
| Dimensions (H x W x D) | 44.5 x 12.7 x 18.0 in (113 x 32.3 x 45.7 cm) |
| Weight | 41 lb (18.6 kg) |
| Power Handling | 200 W RMS, 400 W peak |
| Frequency Response | 24 Hz – 23 kHz ±3 dB |
| Impedance | 4 ohms |
| Sensitivity | 90 dB/2.83V/1m |
| Drivers | 1 x 1.2" folded motion tweeter, 2 x 8" aluminum cone woofers |
| Enclosure Type | Bass reflex with rear-firing port |
| Connectivity | Bi-wire binding posts |
| Recommended Amplifier Power | 20 – 400 W per channel |
| Finish | Black gloss, cherry veneer |
| Warranty | 5 years (speaker), 3 years (electronics) |
| Included Accessories | Grille, rubber feet, floor spikes, manual |
| Maintenance | Wipe with dry cloth; avoid moisture and solvents |
| Safety | Stable placement required; ensure adequate ventilation |
| Repairability | Replaceable drivers and crossover; service by authorized center |
Frequently Asked Questions - Feature Martin Logan
How do I connect the Martin Logan Feature speakers to my amplifier?
Use high-quality speaker cables. Connect the bare wire or banana plugs to the binding posts on the back of the speaker. Ensure positive and negative terminals match the amplifier. For best performance, use bi-wiring if your amplifier supports it.
What is the optimal placement for the Feature speakers?
Place the speakers 2-3 feet from the rear wall and at least 2 feet from side walls. Angle them slightly toward the listening position (toe-in). Avoid placing them in corners to prevent bass booms.
How do I clean the speaker grille and cabinet?
Remove the grille gently; vacuum using a low-suction brush attachment. For the cabinet, wipe with a soft, dry microfiber cloth. Do not use water, alcohol, or abrasive cleaners.
The bass sounds weak. What can I do?
Check speaker placement; move them closer to the rear wall to increase bass. Ensure the rear port is not blocked. Also verify proper amplifier settings and speaker wire polarity.
Can I use the Feature speakers in a home theater system?
Yes, they work well as front left/right channels in a home theater. Pair with a matching Martin Logan center channel and subwoofer for a seamless surround sound experience.
Do I need to break in the speakers?
A break-in period of 20-30 hours at moderate volume allows the suspension parts to loosen. Sound will improve over time, but the speakers perform well from the start.
What amplifier power is recommended?
An amplifier with 20-400 watts per channel into 4 ohms is suitable. Higher power allows for dynamic peaks without clipping. Ensure the amplifier can handle a 4-ohm load.
How do I bi-wire the Martin Logan Feature?
Remove the metal jumper links between the two sets of binding posts. Connect one amplifier channel to the top posts (tweeter) and the other channel to the bottom posts (woofer). Use separate cables for each.
The speaker makes a hissing noise. What's wrong?
Hissing usually comes from the amplifier, not the speaker. Check if the hiss persists with different inputs. If the amp has a high noise floor, consider a quieter source or adding a noise filter.
Where can I find replacement parts or service?
Contact Martin Logan customer support or an authorized service center. Replacement drivers and crossovers are available. Do not attempt internal repairs yourself; it may void the warranty.
User questions about Feature Martin Logan
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual Feature - Martin Logan and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Feature by Martin Logan.