PSB115 - Uncategorized Jandy - Free user manual and instructions
Find the device manual for free PSB115 Jandy in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Pool Pump |
| Model | PSB115 |
| Brand | Jandy |
| Power Source | 115 VAC, 60 Hz, Single Phase |
| Motor Horsepower | 1.5 HP |
| Max Flow Rate | 80 GPM (at typical head) |
| Max Head | 45 feet |
| Port Size | 2-inch NPT inlet and outlet |
| Strainer Basket Capacity | 120 cubic inches |
| Dimensions (L x W x H) | 16 x 8 x 10 inches |
| Weight | 25 lbs |
| Housing Material | Reinforced Thermoplastic |
| Motor Type | Totally Enclosed Fan Cooled (TEFC) |
| Thermal Protection | Auto-reset thermal overload protector |
| Seal Type | Carbon Ceramic Mechanical Seal |
| Sound Level | Less than 70 dB at 3 feet |
| Operating Temperature Range | 32°F to 104°F (0°C to 40°C) |
| Required Protection | GFCI circuit breaker per NEC |
| Warranty | 2 years limited |
| Included Components | Pump unit, strainer housing, owner’s manual |
Frequently Asked Questions - PSB115 Jandy
How do I install the Jandy PSB115 pool pump?
Install the pump on a level, solid surface within 5 feet of the pool water level. Use 2-inch schedule 40 PVC piping for both inlet and outlet. Ensure all connections are tight and use Teflon tape on threaded joints. Wire the pump to a dedicated 115V GFCI protected circuit.
How do I prime the pump?
Remove the strainer lid and fill the strainer basket with water until it overflows. Replace the lid hand-tight. Open the air bleeder valve on the filter if present. Turn on the pump and allow it to run for a few seconds. If it doesn't prime, repeat the process.
Why is my pump making a loud noise?
Common causes include cavitation due to restricted suction, air leaks in the suction line, or debris in the impeller. Check the strainer basket and clean if necessary. Ensure all suction side connections are air-tight. Also, verify the water level is above the skimmer.
How often should I clean the strainer basket?
Clean the strainer basket at least once a week during peak season, or more often if the pump loses pressure. A clogged basket reduces flow rate and can cause motor overheating.
What type of motor oil does the PSB115 require?
This pump has sealed bearings and does not require oil lubrication. Do not attempt to oil the motor. Only qualified personnel should service the motor.
Can I use the pump with a saltwater pool?
Yes, the Jandy PSB115 is compatible with saltwater systems. However, ensure the sacrificial anode is installed and inspected regularly to prevent corrosion.
What is the maximum operating pressure?
The maximum allowable pressure is 50 psi. Operating above this may damage the housing. Use a pressure gauge on the filter to monitor.
How do I winterize the pump?
Drain all water from the pump by removing the drain plugs on the housing. Store the pump in a dry, frost-free area. Loosen the union nuts to relieve pressure. Cover the pump to protect from debris.
Why does the pump trip the circuit breaker?
This could be due to a short circuit in the motor, a ground fault, or an overload. First, check for water intrusion in the electrical box. If not, have a qualified electrician test the motor windings and insulation.
Where can I find replacement parts for the PSB115?
Replacement parts such as seals, impellers, and strainer lids are available from Jandy authorized dealers or online pool supply stores. Use the model number PSB115 to order correct parts.
User questions about PSB115 Jandy
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual PSB115 - Jandy and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PSB115 by Jandy.