GE47S06AAG - Water heater GE - Free user manual and instructions
Find the device manual for free GE47S06AAG GE in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Electric Water Heater |
| Brand | GE |
| Model | GE47S06AAG |
| Capacity | 47 Gallons |
| Voltage | 240V |
| Wattage | 4500W |
| Energy Factor | 0.95 |
| First Hour Rating | 55 Gallons |
| Recovery Rate | 23 Gallons Per Hour |
| Height | 60 Inches |
| Diameter | 22 Inches |
| Weight (Empty) | 180 lbs |
| Tank Material | Glass-Lined Steel |
| Anode Rod | Magnesium |
| Insulation | 2 Inches of Foam |
| Safety Features | Temperature & Pressure Relief Valve, Shut-off Valve |
| Certifications | UL, Energy Star |
| Maintenance | Annual Flushing, Check Anode Rod Every 3 Years |
| Warranty | 6 Years Limited |
| Installation | Indoor, Upright, Requires Drain Pan |
Frequently Asked Questions - GE47S06AAG GE
How do I drain and flush my GE47S06AAG water heater?
Turn off the power at the breaker. Connect a garden hose to the drain valve at the bottom. Open a hot water faucet upstairs to allow air in. Open the drain valve and let water run until clear. Close the valve, refill the tank, and restore power.
What is the recommended temperature setting?
The recommended setting is 120°F (49°C) to balance energy savings and prevent scalding. Adjust using the thermostat dial on the lower front panel.
How often should I replace the anode rod?
Inspect the magnesium anode rod every 3 years. Replace if it is heavily corroded or less than 6 inches long. Regular replacement extends tank life.
Why is my water heater leaking?
Leaks can come from the temperature & pressure relief valve, drain valve, or a tank crack. Check if the T&P valve is releasing due to high pressure. If tank is leaking, you may need to replace the unit.
How do I reset the high-limit switch?
Turn off power. Remove the upper access panel and insulation. Press the red reset button on the thermostat. Replace the panel and restore power. If it trips again, call a professional.
What size circuit breaker does my GE47S06AAG need?
It requires a double-pole 30-amp breaker with 10-gauge wire. Always consult a licensed electrician for proper installation.
Can I install this water heater in a mobile home?
Yes, but it must be installed according to mobile home building codes. Ensure proper earthquake bracing and anchorage.
How do I check the temperature & pressure relief valve?
Lift the lever for a few seconds and release. Hot water should rush out. If not, the valve may be faulty and needs replacement. Perform monthly.
What does the Energy Factor of 0.95 mean?
The Energy Factor (EF) measures efficiency. A 0.95 means 95% of the energy is converted to heat, reducing water heating costs.
Why is my water heater making popping noises?
This is often due to sediment buildup at the bottom. Flush the tank (see question 1) to remove sediment. If noises persist, consider a professional descaling.
User questions about GE47S06AAG GE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water heater in PDF format for free! Find your manual GE47S06AAG - GE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. GE47S06AAG by GE.
USER MANUAL GE47S06AAG GE
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : GE
Model : GE47S06AAG
Category : Water heater