Inspired XPress IS-SPX-1300K - Uncategorized AMX - Free user manual and instructions
Find the device manual for free Inspired XPress IS-SPX-1300K AMX in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | AV Control Processor |
| Model | Inspired XPress IS-SPX-1300K |
| Brand | AMX |
| Dimensions (W x D x H) | 17.0 x 8.5 x 1.7 inches (432 x 216 x 43 mm) |
| Weight | 5.5 lbs (2.5 kg) |
| Power Supply | 100-240 VAC, 50/60 Hz, 0.5A |
| Power Consumption | 30W (max) |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Storage Temperature | -4°F to 140°F (-20°C to 60°C) |
| Humidity (non-condensing) | 10% to 90% |
| Ethernet Ports | 2 x RJ-45 (10/100 Mbps) |
| Serial Ports | 1 x RS-232 (DB9), 1 x RS-485 (terminal block) |
| USB Ports | 1 x USB 2.0 (Type A) |
| IR Ports | 1 x IR output (3.5mm jack) |
| Relay Ports | 2 x relay outputs (terminal block) |
| Supported Control Protocols | ICSLan, TCP/IP, UDP, HTTP, Telnet |
| Memory | 256 MB RAM, 512 MB Flash |
| Processor | ARM Cortex-A8 1 GHz |
| Mounting | Rack-mountable (1U), included brackets |
| Certifications | CE, FCC, RoHS |
| Warranty | 3 years limited |
Frequently Asked Questions - Inspired XPress IS-SPX-1300K AMX
How do I reset the AMX Inspired XPress IS-SPX-1300K to factory defaults?
Locate the recessed reset button on the rear panel. Press and hold it for 10 seconds using a paperclip until the power LED blinks rapidly. The device will reboot with default settings.
What is the default IP address for the IS-SPX-1300K?
The default IP address is 192.168.1.100, subnet mask 255.255.255.0. You can access the web interface via a browser on the same network.
How can I update the firmware?
Download the latest firmware from the AMX website. Connect to the device via its web interface, go to System > Firmware Update, and upload the .bin file. Do not power off during update.
Can I use the IS-SPX-1300K with third-party control systems?
Yes, the device supports open control protocols like TCP/IP, UDP, HTTP, and Telnet. You can integrate it with systems such as Crestron, Extron, or custom scripts.
What does the status LED indicate?
A solid green LED indicates normal operation. Slow blinking green means booting. Red indicates a fault. Off means no power.
How do I connect a projector to the IR port?
Use a 3.5mm mono jack cable. Connect the tip to the IR emitter and sleeve to ground. Configure the IR codes in the device settings for your projector model.
The device is not detecting my serial devices. What should I check?
Verify the baud rate, parity, data bits, and stop bits match the connected device. Check that the DB9 pinout is correct (pin 2 RX, pin 3 TX, pin 5 GND). Use a crossover cable if needed.
Can I power the IS-SPX-1300K via PoE?
No, this model requires an external power supply. The included power adapter provides 12V DC, 2.5A.
How do I clean the device?
Disconnect power. Use a soft, dry cloth to wipe the exterior. Do not use liquids or cleaners. Ensure vents are free of dust.
What should I do if the device is unresponsive?
First, power cycle the device. If still unresponsive, perform a factory reset (see above). If the issue persists, contact AMX support.
User questions about Inspired XPress IS-SPX-1300K AMX
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual Inspired XPress IS-SPX-1300K - AMX and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Inspired XPress IS-SPX-1300K by AMX.
USER MANUAL Inspired XPress IS-SPX-1300K AMX
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : AMX
Model : Inspired XPress IS-SPX-1300K
Category : Uncategorized