CAENIB-7X1 - Uncategorized Crestron - Free user manual and instructions
Find the device manual for free CAENIB-7X1 Crestron in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Control Processor / Interface |
| Brand | Crestron |
| Model | CAENIB-7X1 |
| Power Supply | 24 V DC, 0.5 A |
| Ethernet | 10/100 Mbps, RJ-45 |
| Serial Ports | 2x RS-232 (DB9) |
| IR Ports | 4x IR output (3.5 mm) |
| Relay Ports | 2x relay, 24 V, 1 A |
| Dimensions (H x W x D) | 1.7 x 8.9 x 6.3 in (4.3 x 22.6 x 16 cm) |
| Weight | 1.5 lb (0.68 kg) |
| Mounting | Rackmount (1U) or surface mount |
| Operating Temperature | 32° to 104°F (0° to 40°C) |
| Certifications | CE, FCC Part 15, UL |
| Control Protocol | Crestron SIMPL, e-Control, Crestron Toolbox |
| LED Indicators | Power, Ethernet, activity |
| Reset Button | Yes, recessed |
| Included Accessories | Power supply, mounting brackets, documentation |
Frequently Asked Questions - CAENIB-7X1 Crestron
How do I factory reset the CAENIB-7X1?
Press and hold the recessed RESET button for 10 seconds while powering on the device. Release the button when the LED flashes amber.
What power supply is required?
The unit requires a 24 V DC power supply with a minimum of 0.5 A. Use only the supplied adapter or a Crestron-approved PW-2420RU.
Can I control this device via IP?
Yes, the CAENIB-7X1 has a built-in Ethernet port supporting TCP/IP and UDP communication. It can be programmed using Crestron SIMPL or e-Control.
How many IR outputs are available?
There are 4 IR output ports on the rear panel. Each can drive an IR emitter for controlling devices like cable boxes or amplifiers.
What is the maximum cable length for RS-232?
For reliable operation, keep RS-232 cable length under 50 ft (15 m). Use shielded cables with proper grounding.
Does it support relay closure for projection screens?
Yes, the two relay ports can switch up to 24 V DC at 1 A, ideal for controlling projector screens or motorized shades.
How do I assign an IP address?
Connect via Crestron Toolbox. Use the Device Discovery tool to find the unit, then set a static IP or enable DHCP in the Ethernet configuration.
Can I mount it under a table?
Yes, the included mounting brackets allow for surface or under-table mounting. The device has a low-profile design (1U height).
What are the LED indicators on the front?
There are three LEDs: PWR (green), NET (green for link, blinking for activity), and TX/RX (yellow for serial/IR activity).
Is the CAENIB-7X1 compatible with older Crestron systems?
Yes, it supports legacy SIMPL Windows programming and can integrate with Crestron 2-Series and 3-Series control systems.
User questions about CAENIB-7X1 Crestron
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual CAENIB-7X1 - Crestron and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CAENIB-7X1 by Crestron.
USER MANUAL CAENIB-7X1 Crestron
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Crestron
Model : CAENIB-7X1
Category : Uncategorized