Z1502i - Receiver PHOENIX GOLD - Free user manual and instructions
Find the device manual for free Z1502i PHOENIX GOLD in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Car Audio Amplifier |
| Brand | Phoenix Gold |
| Model | Z1502i |
| Number of Channels | 2 |
| RMS Power Output | 150W x 2 at 4 ohms |
| Peak Power Output | 300W x 2 |
| Frequency Response | 20 Hz - 20 kHz |
| Total Harmonic Distortion (THD) | < 0.05% |
| Signal-to-Noise Ratio | > 100 dB |
| Input Impedance | 10 kOhms |
| Minimum Load Impedance | 2 ohms bridged |
| Crossover Type | Variable low-pass/high-pass |
| Input Voltage | 12V DC |
| Dimensions (L x W x H) | 10.2 x 7.1 x 2.1 inches |
| Weight | 5.5 lbs |
| Protection Circuits | Short circuit, thermal, overload |
| Cooling | Convection |
| Mounting Type | Surface mount |
Frequently Asked Questions - Z1502i PHOENIX GOLD
What is the RMS power output of the Phoenix Gold Z1502i?
The Phoenix Gold Z1502i delivers 150 watts RMS per channel at 4 ohms, for a total of 300 watts RMS.
Can the Z1502i be bridged?
Yes, the Z1502i can be bridged into a single channel, delivering up to 300 watts RMS at 4 ohms (bridged). Minimum load in bridged mode is 4 ohms.
What type of crossover does the Z1502i have?
The amplifier features a variable low-pass and high-pass crossover, allowing you to tailor the frequency response to your speakers and subwoofers.
What are the recommended speaker impedance ratings?
The Z1502i is stable into 2 ohms when bridged, and into 4 ohms per channel in stereo mode. Using lower impedances may cause overheating or damage.
How do I wire the Z1502i to my car battery?
Connect the amplifier's power terminal to the battery positive terminal using a fused power cable (at least 8 AWG). The ground terminal should be connected to a clean chassis ground point. Use at least 8 AWG wire for ground as well.
What is the recommended fuse size for the Z1502i?
The built-in fuse is typically 30A. For the inline fuse near the battery, use a 30A fuse with an appropriate holder and wire gauge.
Does the Z1502i have remote turn-on?
Yes, the amplifier has a remote turn-on terminal (REM) that accepts a 12V signal from the head unit's remote output to power on the amplifier.
What is the frequency response range of the Z1502i?
The frequency response is 20 Hz to 20 kHz, suitable for full-range audio reproduction.
How do I adjust the gain on the Z1502i?
Use a small flathead screwdriver to adjust the gain potentiometer. Start with the gain at minimum, play a clean test tone at 3/4 volume on your head unit, then increase gain until you hear distortion, then back off slightly.
What should I do if the amplifier goes into protection mode?
First, turn off the system and check for short circuits in speaker wiring. Ensure the amplifier is not overheating and that the impedance load is within specifications. If the problem persists, check the fuse and power supply connections.
User questions about Z1502i PHOENIX GOLD
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual Z1502i - PHOENIX GOLD and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Z1502i by PHOENIX GOLD.
USER MANUAL Z1502i PHOENIX GOLD
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : PHOENIX GOLD
Model : Z1502i
Category : Receiver