88198 - Snow blower Craftsman - Free user manual and instructions
Find the device manual for free 88198 Craftsman in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Snow Blower |
| Brand | Craftsman |
| Model | 88198 |
| Engine Type | 4-Cycle, Overhead Valve |
| Engine Displacement | 208 cc |
| Fuel Type | Unleaded Gasoline (87 octane or higher) |
| Oil Type | SAE 5W-30 (above 32°F: SAE 30) |
| Starting System | Electric Start (120V) with Recoil Backup |
| Clearing Width | 24 inches |
| Intake Height | 13 inches |
| Discharge Chute | Remote Controlled, 180° Rotation |
| Drive System | Friction Disc |
| Speeds | 6 Forward, 2 Reverse |
| Wheel Size | 13 x 4.00-6 |
| Weight | 245 lbs |
| Dimensions (L x W x H) | 57 x 24 x 45 inches |
| Headlight | Yes |
| Heated Handles | Yes |
| Skid Shoes | Adjustable |
| Safety Features | Safety Key, Auger Brake |
| Oil Capacity | 20 oz (0.6 L) |
| Fuel Tank Capacity | 1.9 quarts |
| Shear Pins | Standard Auger Shear Pins (replacement part #751-0440) |
| Warranty | 2-Year Limited Warranty |
Frequently Asked Questions - 88198 Craftsman
How do I start the Craftsman 88198 snow blower?
Ensure the auger brake is disengaged and the fuel shut-off valve is open. Insert the safety key. For electric start, plug into a 120V outlet and press the start button. Alternatively, use the recoil starter. Allow engine to warm for 2-3 minutes before engaging auger.
What type of oil is recommended for the 88198?
Use SAE 5W-30 for temperatures below 32°F (0°C) or SAE 30 for warmer conditions. Check oil level before each use and change every 50 hours of operation.
How do I change the oil on my Craftsman snow blower?
Run the engine to warm the oil, then turn off and disconnect the spark plug. Remove the oil drain plug (located under the engine) and drain oil into a pan. Replace drain plug, refill with fresh oil (approx. 20 oz), and reinstall dipstick.
How do I adjust the skid shoes on the 88198?
Loosen the nuts on the skid shoes. Adjust them to the desired height (typically 1/4 inch above the ground for driveways). Tighten nuts securely. Adjust both sides evenly to prevent uneven wear.
How do I replace the shear pins on the auger?
Remove the damaged shear pin by pulling it out. Align the holes in the auger shaft and housing. Insert a new shear pin (part #751-0440) and secure with the cottter pin. Never replace with a bolt or stronger pin as it may damage the machine.
How should I store the snow blower during summer?
Run the engine dry of fuel or add fuel stabilizer. Change the oil. Remove the spark plug and add a teaspoon of oil into the cylinder, then pull recoil slowly to coat. Clean the unit thoroughly and store in a dry place.
Why is my snow blower not throwing snow far enough?
Check the chute deflector height and adjust if needed. Ensure the auger is not clogged with ice or debris. Verify the drive belt is not slipping. The impeller may need to be checked for damage. Also ensure RPM is at maximum throttle.
How do I replace the drive belt on the 88198?
Remove the belt cover. Release tension from the idler pulley. Slide the old belt off the pulleys. Route the new belt according to the diagram (usually around engine pulley, friction disc, and auger pulley). Re-tension and replace cover.
What fuel should I use in my Craftsman snow blower?
Use fresh, unleaded gasoline with a minimum octane rating of 87. Avoid ethanol blends greater than 10% (E10). Never use E85 or diesel. Add fuel stabilizer if storing for more than 30 days.
How do I check and replace the spark plug?
Disconnect the spark plug wire. Remove the plug with a 5/8 inch socket. Inspect for wear or fouling. The gap should be 0.030 inches (0.76 mm). If worn, replace with a Champion RN9YC or equivalent. Torque to 20 ft-lbs.
User questions about 88198 Craftsman
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Snow blower in PDF format for free! Find your manual 88198 - Craftsman and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 88198 by Craftsman.
USER MANUAL 88198 Craftsman
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Craftsman
Model : 88198
Category : Snow blower