AVC-4320 - Receiver DENON - Free user manual and instructions
Find the device manual for free AVC-4320 DENON in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | AV Receiver |
| Brand | Denon |
| Model | AVC-4320 |
| Channels | 5.1 |
| Power Output | 100W per channel (8 ohms, 20Hz-20kHz, 0.08% THD) |
| Supported Audio Formats | Dolby Digital, DTS, Dolby Pro Logic II |
| Tuner | AM/FM with 30 presets |
| Inputs | 4x composite video, 2x S-Video, 2x component video, 5x stereo audio, 1x optical, 1x coaxial |
| Outputs | 1x composite monitor, 1x S-Video monitor, 1x component monitor, 1x subwoofer pre-out, speaker terminals |
| Remote Control | Included |
| Dimensions (W x H x D) | 17.1 x 6.1 x 15.4 inches |
| Weight | 24.3 lbs |
| Power Consumption | 450W (standby 0.5W) |
| Impedance | 6-16 ohms |
| Signal-to-Noise Ratio | 100 dB |
| Frequency Response | 10Hz-100kHz (+1/-3 dB) |
| Maintenance | Clean with dry cloth, avoid liquids |
| Safety | Do not expose to moisture, unplug during storms |
| Repairability | Service by qualified personnel only |
| Accessories Included | Remote, batteries, FM antenna, AM loop antenna |
Frequently Asked Questions - AVC-4320 DENON
How do I connect my TV to the AVC-4320?
Use a composite, S-Video, or component video cable from your TV's output to the corresponding input on the receiver. For audio, connect an optical or coaxial digital cable, or analog stereo cables.
Why is there no sound from the speakers?
Check that the receiver is powered on and the correct input is selected. Ensure speaker wires are securely connected to the speaker terminals and the impedance matches (6-16 ohms). Also, verify that the mute function is off and the volume is turned up.
How do I reset the receiver to factory settings?
With the receiver off, press and hold the POWER button and the MULTI ZONE button simultaneously until the display flashes. Release the buttons. This will restore all settings to default.
Can I use this receiver with a 4K TV?
The AVC-4320 does not support HDMI or 4K passthrough. Video inputs are limited to composite, S-Video, and component (480i/480p). For 4K, connect video directly to the TV and use the receiver only for audio.
How do I set up the FM antenna?
Connect the included FM dipole antenna to the FM 75 ohms terminal. Extend the antenna and adjust its position for best reception. For AM, connect the AM loop antenna and rotate it for optimal signal.
What speaker impedance is recommended?
The receiver is designed for speakers with 6 to 16 ohms impedance. Using speakers with lower impedance may cause overheating or damage. Always check your speaker specifications.
How do I clean the receiver?
Use a soft, dry cloth to wipe the exterior. Do not use any liquid cleaners or abrasive materials. Avoid getting moisture into vents or openings. Unplug the receiver before cleaning.
Can I bi-wire my speakers?
Yes, if your speakers support bi-wiring, you can connect two sets of speaker wires to the same speaker terminals on the receiver (one for the woofer, one for the tweeter). Ensure the metal jumpers on the speakers are removed.
How do I update the firmware?
This model does not have firmware updates as it is a non-network receiver. All features are hardware-based and cannot be upgraded via software.
Where is the serial number located?
The serial number is printed on a sticker on the rear panel of the receiver, near the power cord. It is also listed in the original packaging and user manual.
User questions about AVC-4320 DENON
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual AVC-4320 - DENON and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AVC-4320 by DENON.