4C-WZ38BNH-400 - Uncategorized Prebena - Free user manual and instructions
Find the device manual for free 4C-WZ38BNH-400 Prebena in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Pneumatic Nailer |
| Model | 4C-WZ38BNH-400 |
| Brand | Prebena |
| Dimensions (L x W x H) | 280 x 260 x 80 mm |
| Weight | 1.4 kg (3.1 lbs) |
| Operating Pressure | 5–8 bar (70–115 psi) |
| Air Inlet | 1/4 inch NPT |
| Magazine Capacity | 100 nails |
| Fastener Gauge | 18 gauge |
| Fastener Length Range | 15–50 mm (5/8–2 inches) |
| Operating Mode | Contact trip and sequential trip |
| Loading System | Rear loading with open magazine |
| Noise Level | ≤ 90 dB(A) |
| Vibration Level | ≤ 2.5 m/s² |
| Safety Features | Contact safety trigger, no-dry fire mechanism |
| Maintenance | Daily lubrication via air inlet; periodic cleaning of magazine |
| Repairability | Spare parts available; service kits recommended |
| Warranty | 1 year limited |
| Certifications | CE, ANSI |
Frequently Asked Questions - 4C-WZ38BNH-400 Prebena
What type of nails does the Prebena 4C-WZ38BNH-400 use?
This nailer uses 18-gauge nails with lengths from 15 to 50 mm. Always consult the manual for exact fastener specifications.
What is the recommended operating pressure?
The recommended operating pressure is 5–8 bar (70–115 psi). Use only clean, dry air to prevent damage.
How do I lubricate the nailer?
Add 2–3 drops of pneumatic tool oil into the air inlet before each use or after every 2 hours of operation. Use non-detergent oil.
Why is the nailer not driving nails fully?
Check the air pressure is within the required range, ensure the magazine is not jammed, and clean the driver blade. Also verify the nails are correct for the tool.
Can I use the nailer with a compressor?
Yes, it requires an air compressor capable of delivering 5–8 bar and sufficient CFM (at least 1.5 SCFM at 80 psi) for continuous operation.
How do I clear a jam?
Disconnect the air supply. Open the magazine and remove any jammed nails. If necessary, use a small screwdriver to clear the nose area. Never use force.
What is the difference between contact trip and sequential trip?
Contact trip allows rapid nailing by holding the trigger and bumping the nosepiece. Sequential trip requires pressing the nosepiece first, then pulling the trigger for each nail, improving safety.
Is the nailer suitable for hardwood?
It can handle hardwood, but pre-drilling or using collated nails of appropriate length is recommended. Ensure the air pressure is on the higher end (7–8 bar).
Where can I find the serial number?
The serial number is usually stamped on the back or side of the housing near the air inlet. It is needed for warranty and spare parts.
What spare parts are commonly needed?
Common spare parts include O-rings, driver blades, and magazine springs. Prebena offers service kits with these items.
User questions about 4C-WZ38BNH-400 Prebena
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual 4C-WZ38BNH-400 - Prebena and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 4C-WZ38BNH-400 by Prebena.
USER MANUAL 4C-WZ38BNH-400 Prebena
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Prebena
Model : 4C-WZ38BNH-400
Category : Uncategorized