MOOV 500 - Navigation GPS MIO - Free user manual and instructions

USER MANUAL MOOV 500 MIO

This manual provides information on the hardware and non-navigation features. For navigation software information, please refer to the other manual. ROO (USA) Trademarks All brand and product names are trademarks or registered trademarks of their respective companies. Disclaimer Specifications and documents are subject to change without notice. Mio Technology does not warrant this document is error-free. Mio Technology assumes no liability for damage incurred directly or indirectly from errors, omissions, or discrepancies between the device and the documents. Notes Not all models are available in all regions. Depending upon the specific model purchased, the color and look of your model may not exactly match the graphics shown in this document The screenshots and other presentations shown in this document are for reference only. They may differ from the actual screens and presentations generated by the actual product.

Table of Contents Getting to know your Mio Performing the initial start-up Charging the battery via the USB cable. Using your Mio in a vehicle... Operating basic... Tuning on and off... Shutdown and hardware rese Navigating on the screen Reference Inserting a memory card Troubleshooting... Caring for your Mio Regulatory information Regulations statements. Federal Communications Commission (FCC) statement Canada … Safety precautions. About charging… About the charger About the battery

Getting to know your Mio Name Description © | Power switch Turns your Mio on and off. @ | Memory card slot | Accepts a SD (Secure Digital), SDHC (Secure Digital High Capacity), or MMC (MultiMediaCard) card for accessing data such as additional maps. © | Charge indicator | Indicates the level of battery charge: Green - battery full Amber - battery charging. © | Mini-UsB Connects to the charger or USB cable. connector © | Holder socket For the holder. @| Speaker Sends out sounds and voice.

Performing the initial start-up

1. Forthe initial start-up, slide the power switch to the ON position.

2. Your Mio turns on.

Note: The battery may not be fully charged when you use your Mio for the first time. To charge the battery, see the next section.

3. Follow the prompts. During the start-up process, you can select your preferred language, read the warning

message, and view the tutorial. Note: To prevent the language selection screen and tutorial from displaying again on the next start-up, clear the check box on the screen 4... The map screen will display. You can now use your Mio

Charging the battery via the USB cable If you intend to charge your Mio in this way, turn off your Mio so that it takes less time to charge the battery.

1. Turnonthe computer.

2. Connect the mini-USB end of the USB cable to the bottom of your Mio and the other end to a USB port on

3. The charge indicator glows amber when charging is in progress. When the battery is fully charged, the

indicator turns green. Note: f your Mio is on when connected to a computer, a screen appears to prevent you from using your Mio. Note: When the Mio is connected to a computer, it is recognized as an external mass storage device. Do not delete any files pre-installed in the Mio. Deleting files of which the function is unknown can cause programs or features to malfunction. CAUTION: For optimal performance of the lithium battery: = Do not charge the battery where the temperature is high (e.g. in direct sunlight). = Thereis no need to fully discharge the battery before charging « …Fully charge the battery at least every two weeks. Not charging the battery can affect the battery's performance.

Using your Mio in a vehicle CAUTION: = Select an appropriate location for mounting the Mio in a vehicle. Never place the is blocked. » Notice to all drivers: Certain states prohibit the installation of product on a vehicle's windshield. Those that are known as of the release date of this product are listed below, however, please make sure that you are in compliance with your state's most recent law before installing this product. Mio Technology is not responsible for any damages, penalties, or fines that may occur as a result of ilegal installation. Notice to customers driving in California and Minnesota: Use the dashboard mount option when installing this. product, as state law prohibits the installation of products on vehicle windshields. Refer to California Vehicle Code 26708, and Minnesota Statutes 169.71 for detail. = Ifthe car's windscreen is tinted with a reflective coating, it may be athermic and impact the GPS reception. In this instance, please mount your Mio where there is a “clear area." = To protect your Mio against sudden surges in current, connect the car charger only after the car engine has been started. where the drivers field of vision

Operating ba Turning on and off For normal operation, turn off your Mio by sliding the power switch to the OFF position. Your Mio enters a suspended state. To use it again, slide the power switch to the ON position. Your Mio will be back to where you left off, Shutdown and hardware reset Occasionally, you may need to perform a hardware reset when your Mio stops responding; or appears to be “frozen” or “locked-up." You can perform a hardware reset by shutting down your Mio and then turning it back on. To shut down your Mio, slide the power switch to the RESET position. To turn on your Mio after shutting it down, slide the power switch to the ON position. Navigating on the screen To operate your Mio, touch the screen with your fingertip. You can perform the following actions: = Tap Touch the screen once with your fingertip to open items or select onscreen buttons or options. = Drag Hold your fingertip on the screen and drag up/down/left/right or across the screen. (This is not supported by all applications.)

• Tapandhold Tap and hold your fingertip until an action is complete, or a result or menu is shown. (This is not supported by all applications.)

Reference Inserting a memory card CAUTION: Do not apply pressure to the centre of the memory card. Hold the card (SD, SDHC, or MC) by the edges and gently insert it into the slot with the label facing the front ofthe Mio. To remove a card, gently push the top edge of the card inwards to release it, and pull it out of the slot. Troubleshooting Note: f you encounter a problem you cannot solve, contact an authorized service center for assistance. Problems Solutions Power does not turn on when using battery | The remaining battery power may be too low to run your Mio. Charge the power. battery. Screen responds slowly. Make sure that your Mio is not running out of battery power. Ifthe problem still persists, reset your Screen freezes. Reset your Mio. (See “Shutdown and hardware reset” for information.) Screen is hard to read. Make sure that the backlight of the display is set to a high-enough brightness. Cannot establish a connection with a Make sure that your Mio and your computer are both turned on before trying computer. to establish a connection Make sure that the cable is securely plugged into the USB port on your computer and on the Mio. Connect the USB cable directly to your computer—do not run the cable through a USB hub. Reset your Mio before connecting the cable. Always disconnect your Mio before you restart your computer.

Caring for your M Taking good care of your Mio will ensure trouble-free operation and reduce the risk of damage to your Mio. = Keep your Mio away from excessive moisture and extreme temperatures.

• Avoid exposing your Mio to direct sunlight or strong ultraviolet light for extended periods of time. = Do not place anything on top of your Mio or drop objects on your Mio.

• Do not drop your Mio or subject it to severe shock

• Donot subject your Mio to sudden and severe temperature changes. This could cause moisture condensation inside the unit, which could damage your Mio. In the event of moisture condensation, allow the Mio to dry out completely before use.

• The screen surface can easily be scratched. Avoid touching it with sharp objects. Non-adhesive generic screen protectors designed specifically for use on portable devices with LCD panels may be used to help protect the screen from minor scratches.

• Never clean your Mio with it powered on. Use a soft lint-free cloth to wipe the screen and the exterior of your Mio. “Do not use paper towels to clean the screen.

• Never attempt to disassemble, repair or make any modifications to your Mio. Disassembly, modification or any attempt at repair could cause damage to your Mio and even bodily injury or property damage and will void any warranty.

• Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your Mio, its parts or accessories.

Regulatory information Note: For regulatory identification purposes, Moov 500-Series is assigned a model number of N210. Regulations statements

Federal Communications Commission (FCC) statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 oftthe FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: = Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCCRF radiation exposure statement (only for models with Bluetooth capabilities) This transmitter must not be co-location or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Canada This Class B digital apparatus complies with Canada ICES-003 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term “IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

Safety precautions Prolonged listening of music in maximum volume can damage the ears. About charging Use only the charger supplied with your device. Use of another type of charger will result in malfunction and/or danger. This product is intended to be supplied by a LISTED Power Unit marked with “LPS”, “Limited Power Source” and output rated + 5 V de / 1.0 A”. Use a specified battery in the equipment. About the charger Do not use the charger in a high moisture environment. Never touch the charger when your hands or feet are wet. Allow adequate ventilation around the charger when using it to operate the device or charge the battery. Do not cover the charger with paper or other objects that will reduce cooling. Do not use the charger while it is inside a carrying case. Connect the charger to a proper power source. The voltage requirements are found on the product case and/or packaging Do not use the charger if the cord becomes damaged Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. About the battery Use a specified battery in the equipment. CAUTION: This unit contains a non-replaceable internal Lithium lon battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, puncture, or dispose of in fire or water. Important instructions (for service personnel only) Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Replace only with the same or equivalent type recommended by the manufacturer. The battery must be recycled or disposed of properly. Use the battery only in the specified equipment.

Moov 500-Series MioMap Manual L © English explore more

Mio Moov 500-Se: s_|_Important safety information Important safety information PLEASE READ CAREFULLY BEFORE INSTALLING PRODUCT IN VEHICLE ‘This is the safety alert symbol. It is used to alert you lo potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicate à polenta hazard SUB WI no avelded, ay Feu in minor or oder ACAUTION || CAUTION ve wihoutire say en symbol idicats à potenalyRazardous son MN Irma CAUTION _]} soie may eau propory damage Removing original equipment, adding accessories or modifying your vehicle could affect the vehicle's safety or make it ilegal to operate in some jurisdictions, Follow al product instructions and al instructions in your vehicle owners manual regarding accessories or modifications. Consul your countrÿs and/or state's laws regarding operation of a vehicle with any accessories or modifications. IL is your sole responsibility to place, secure and use your Mio in a manner that will not cause accidents, personal injury or property damage. Always observe safe driving practices, Do not mount your Mio in à way that may interfere with the safe operation of ihe vehicle, the deployment of air bags or other safety equipment. Do not operate your Mio while driving. Before you use your Mio for the first lime, familirize yourself with your device and its operation (On main roads, the distance to an exit calculated by the Mio may be further than the distance shown on road signs. Road signs show the distance Lo the'start of an exit while {he Mio shows Ihe distance lo the next intersection, Le., the end of the exit ramp or road, To prepare Lo exit a road, always follow distance information on road signs. ‘The use of information regarding safety or speed camera locations may be subject to local laws in he country of use. You are responsible for checking that you can legally use the information in your country or in the country where the information will be used Do not handle the Mio while it is hot. Let the product cool, out of direct sunlight. Atfull power, prolonged listening to the Mio via headphones or earphones can damage the ear of ine user. Do not expose the Mio to direct sunlight in an unattended vehicle for prolonged periods. Overheating may damage the unit To discourage theft, do not leave your Mio, mounting bracket or any cables in plain view in an unattended vehicl

Mio Moov 500-Series |_Important safety information Home Charger-specific safety information To charge your Mio from the power, use the home charger (Model: PSAAOSR-050; Input: 100-240V AC 50-60Hz; Output: 5V DC 1A Max) supplied by Mio as an accessory (may be sold separately). Using other home chargers with your Mio could result in serious injury or property damage. Never use the charger if he plug or cord are damaged. Do not expose the charger to moisture or water. Do not use the charger in a high moisture environment. Exposure lo water may cause electrical sparks or fires. Never touch lhe charger when your hands or feet are we. Allow adequate ventilation around the charger when using it to operate your Mio or charge the Mio intemal battery. Do not cover the charger wilh paper or olher objects hat will reduce ventilation. Do not use he charger while it is inside à camying case or other container. Ensure that the charger is connected lo a power source with lhe correct fiing and voltage requirements. The voltage requirements can be found on the home charger casing andlor packaging. Do not attempt to service the charger as this could result in personal injury. Replace the charger if it is damaged or exposed to excess moisture. Internal battery-specific safety information ‘The Mio contains à non-replaceable intemal lithium-ion polymer battery. The battery may burst or explode if mishandied, releasing hazardous chemicals. To reduce the risk offre or bums, do not disassemble, crush or puncture the battery. Recycle or dispose of the battery safely and properly according lo local laws and regulations. Do not dispose of the battery in Only use the correct power charger (sold separately) or invehicle charger supplied by Mio to charge the Mio internal battery. Only use the Mio internal battery with the Mio unit. ‘The Mio batiery will top charging when the ambient temperature is less than 0°C (32°F) or more than 45°C (113°F). Warning Notice to Drivers in the United States State law may prohibit drivers in states such as Arizona, Califomia and Minnesola from mounting objects on their windshields while dring. Please make sure you research and follow your most current State laws. An alternative mounting option Is provided in the box with your product, also, stores offer additional mounting altematives. Mio does not take any responsibility for any fines, penallies, or damages ihat may be incurred as a result of disregarding this notice. Failure to adhere to these wamings and cautions may lead to death, serious injury or property damage. Mio disclaims all liabiity for installation or use of the Mio that causes or contributes to death, injury or property damage or that violates any law.

Mio Moov 500-Series | Contents Contents Important safety information... Welcome……… Important information for using the manual . How do | get started? How do ! turn my Mio on for the first time? How do | adjust the volume? How do | monitor the battery status’ What are the main screens | will use? Main Menu screen Map screens … How do | navigate with GPS? … How do 1 go from À to B?.. What if | miss a turn? …. How do 1 search for an address? … Case Study: How do 1 search for an address? Using the Keyboard screen . Using the Destination Search screen. How do | create a trip with multiple stops? : Case Study: How do ! navigate to multiple addresses? . How do | skip a waypoint during a mult-Stop trip? How do | search for a Point of Interest (POI)? Case Study: How do | search for a Point of Interest? How do | save Favorites and My Home? How do | save a Favorite or My Home? How do | navigate to a Favorite?.. How do | navigate to My Home? How do | edit the name of a Favorite? How do | delete a Favorite? …… How do | navigate to a recent location? … How do | view my route? 3D Map screen 2D Map screen Traffic Overview screen Route Overview screen. Tum-by-Turn screen . How do | use the Map Menu? … How do | avoid an area? … How do | add an Avoid Area? How do | delete an Avoid Area? How do | delete all Avoid Areas? . How do | preview a route? … How do | view my route statistics? . How do | view statistics on my current route? … How do | view statistics of my trips to date?.. Trafic. How does my Mio receive trafic information? How will | know when a Traffic Event occurs? How do | view a list of all events on my route?. How do | view traffic details? How do 1 know if a delour is recommended?

GPS Status 1/2. Set GPS Mode 2/2. Language…. Trafic. Traffic System Status Traffic Event Notificatior Select event soring type Power .. Keyboard . How does precitive text (bc, Units Units 1/2... Units 2/2. Start-up. Saved Information. Tutorial . What is MioMore À Desktop? Can | use MioMore Desktop with my computer?.. How do | install a map for the first time? How do install MioMore Desktop onto my computer MioMore Desktop features … How do | keep MioMore Desktop up-to-date? MioMore Desktop Preferences My Maps. How do | install maps onto my Mio? . How do | install maps from DVD? . How do | remove maps from my Mio? . How do | know which map contains a particular city or town? My Map Preferences. What is a Major Road Network map? … Photo Album . Toolbar . How do | use Photo Album?. How can | view and edit pictures or albums on my computer? What else can | do with pictures and albums on my computer?. Photo Album Preferences. Image Search . How do | download NavPix from the internet? How do | import NavPix to Photo Album? My subscriptions . How do | install Safety Camera information? …. How do | know which Safety Camera information is available? Purchase a Subscription. Activate your Subscription How do | update Safety Camera information on my Mio? . Voice Transfer How do | install a Voice ile’

Mio Moov 500-Series | Contents How do | remove a voice file? How do | backup my Mio? Reference … Point of Interest categories Traffic and other TMC Events For more information...

Mio Moov 500-Ser s | Welcome Welcome Thank you for purchasing this Mio. This manual has been prepared to guide you through the operation of your Mio from first set-up through to continuous use. Please read this manual carefully before using your Mio for the first time Keep this manual in a safe place and use as your first point of reference. Important information for using the manual Itis important to understand the terms and typographical conventions used in this manual. Formatting The following formatting in the text identifies special information: Convention | Type of Information Bold Mio components or items displayed on screen, including buttons, headings, field names and options. Ialics Indicates the name of a screen. Icons The following icons are used throughout this manual: Icon Description L Case study A Waming Terms The following terms are used throughout this manual to describe user actions. Term Description Tap Press and release an item displayed on the touch screen. Tap and hold | Tap and hold an iem displayed on the touch screen for 2-3 seconds Select Tap an item in a list or tap a command from a menu

Mio Moov 500-Series |_How do 1 get started? How do I get started? Note: The first time you use your Mio, it may take up several minutes to establish a GPS connection. For more information about GPS, refer to the GPS Frequently Asked Questions guide on the enclosed DVD. ime? How do | turn my Mio on for the first To get started for the first time, complete the following steps:

1. Readthe Important Safety Information on page 3.

2. Position your Mio

Follow the instructions below to position your Mio in your vehicle: sw, or interfere with the operation of the vehicle airbags and Note: Ensure that your Mio does not obstruct the driver's safety devices.

Mio Moov 500-Series |_How do 1 get started? Turn your Mio on Your Mio will turn on and display the Language screen. Select your preferred language From the Select Language screen, tap your preferred language. km @ 24 CES = “a Da écstire Ile)

En Dex km © 24 PM Deutsch 14x0 check box. Read the warning message To prevent the Select Language screen from displaying on each start-up, clear the Show on start-up You can change your preferred language while using your Mio (see Language" on page 67). a) The Safety Agreement screen will display after you have selected your preferred language. Read the Safety Agreement message. b) To confirm that you have read and understood the message, tap Accept. The Tutorial wili display.

When you have accepted the Safety Agreement, the first Tutorial screen wil display.

• To prevent the Tutorial from displaying again on start-up, clear the Show on start-up check box. = To move forward through the Tut To view the previous screen, tap ! screens, tap = To view the Tutorial again while using your Mio, see “Tutorial” on page 77. Note: If ou have maps installed from multiple continents, you may be prompted to select the maps you require. To use maps from a different continent at a later time, you can select a different map via the Select Map screen in the Select Map 3/3 preferences; refer lo page 61 When you have finished the Tutorial, the 3D Map screen will display. If you have a GPS fix, your current location will be displayed on the map. How do I adjust the volume? The volume on your Mio can be adjusted by the volume control on the Volume preference screen. To mute he volume from the map screens, tep D and inen top M To adjust he volume, tap and hoié DÉÜBN t display he Volume preference screen. Base BA soeck heyboerdteters For more information on how to adjust the volume on your Mio, see “Volume” on page 63.

Moov 500-Series | How do 1 get started? How do 1 monitor the battery status? Your Mio has an internal battery that when fully charged, should provide power for up to 3 hours. The battery indicator light on the top of the Mio indicates the level of internal battery charge: + Green - battery full

• Orange - battery charging You can monitor battery power status on the Power screen. To access the Power screen, tp MSI ana noid RSS on ine map screens. «l Power How do 1 charge the battery? The Battery Status bar displays External Power while the battery is charging; when the battery is fully charged, the Battery Status bar will display at 100%. = To charge your Mio in a vehicle, plug the in-vehicle charger into * = on the bottom of your Mio and the other end into the vehicle power socket. = To charge your Mio using your computer, plug the large end of the USB cable directly into a USB port on your computer (not a USB hub) and plug the small end into - = on the bottom of your Mio. To begin charging, ensure your Mio is tumed off. = To charge your Mio using a power socket, plug the power charger cable into -*" on the bottom of the Mio and the power charger power pack into the power socket. Note: The power charger is not included with all models and may be purchased separately

Mio Moov 500-Series |_What are the main screens | will use? What are the main screens | will use? Main Menu screen The Main Menu screen is your starting point for searching for a destination and allows you to customize references. The Main Menu can be accessed from the map screens by tapping MES or by tapping the status bar atthe bottom of any screen. Note: The Main Menu screens may difer from Ihose displayed above, depending on your Mio model Map screens There are five map screens used to view the route to your destination: = 3D Ma = 2DMeæ

• Traffic Overview (if available) “Route Overview " Tumby-Tum The Map screens can be accessed from the Main Menu screen by tapping A. You can eye through 1e diferent map screens by pressing [©] on any map screen {he name ofthe map screen väll display brieñy as your cycle through). = For more information on the map screens, see “How do | view my route?" on page 33. = Forinformation on using the Map menu from the 3D Map and 2D Map screens, see ‘How do | use the Map Menu? on page 43.

Mio Moov 500-Series |_How do | navigate with GPS? How do | navigate with GPS? The Global Positioning System (GPS) is available at any time, free of charge, and is accurate to within 5m (15ft) GPS navigation is made possible by a network of satelites that orbit {he Earth at around 20,200km (12,552mi). Each satelite transmits a range of signals which are utilized by GPS receivers, such as your Mio, to determine an exact location. Although a GPS receiver can detect signals from up to 12 satelies at any time, only four signals are required to provide a position or "GPS fx" (latitude and longitude), for vehicle navigation systems. How does my Mio receive GPS signals? Your Mio receives GPS signals via the intemal GPS antenna. To guarantee the optimum GPS signal strength, ensure your Mio is outdoors, or in a vehicle outdoors, and has an unobstructed view of the sky. GPS reception is not usually affected by weather, however, very heavy rain or snow may have a negative effect on your reception How do 1 view my GPS status? You can view your GPS status at any time from the map screens orthe Viewfnder screen. * - «1 displays green when a GPS fix is established and red when a GPS fx is unavailable. To indicate the reception strength of a GPS fix,

displays between one and four green vertical bars. = To view your GPS status in more detail, see "GPS Status" on page 65.

• To set your GPS mode, see “Settng your GPS mode” on page 66. = For more information about GPS, refer to the GPS Navigation - Frequentiy Asked Questions guide on the MioMore Desktop DVD.

Mio Moov 500-Series |_How do | go from A to B? How do | go from A to B? Your Mio is equipped with maps that provide street-level detail for door-to-door navigation, including Points of Interest such as accommodation, parking areas, gas stations, railway stations and airports. When you . Then know {he address of your destination use the address-entry wizard to enter the address low do 1 search for an address?" on page 16. want lo make multiple stops use the Muli-stop Trip Planner screen Lo enter muliple waypaints + see "How do create a trip with multiple stops?" on page 20. need to find a named site, feature, landmark or public venue search for a Point of Interest »___see “How do 1 search for a Point of Interest (POI)?" on page 25. A WARNING For your safety, enter destination information before you start a journey. Do not enter a destination while driving. What if ! miss a turn? Back-On-Track"” Automatic Rerouting You will be redirected if you make a wrong turn. À message informing you that your route is being re-calculated will display at the top of the screen To cancel a route re-calculation tap L*}. A warning will display, asking you to confirm the cancellation. If confirmed, both the re-calculation and your current route will be cancelled.

Mio Moov 500-Series |_How do 1 go from A to 8? How do I search for an address? Enter a destination using the Destination Search, Keyboard and Preview screens, which used together form an address-entry wizard This section provides a case study to help guide you through setting your destination. Note: In some countries, you can search for your destination by postcode or zip code. Quick Steps

4. Search for the street

Search for the house number

T4 Case Study: How do I search for an address? This case study will show you how to enter an address and how to navigate to it. The address we will be using in this example is: 118 Mio Avenue New York New York 10017 USA. Note: The above address is fictiious and used as an example only. Before you enter your destination address, ensure that you have set your roule preferences. For more information, see ‘Route Options” on page 55.

The Destination Search screen will display. Note: If {his is the first time you are setting your destination and you have maps from more than one country installed, then the Select a map screen wil display instead of the Destination Search screen. Go direct to step 2b. The next time you perform this procedure, Ihe Destination Search screen wall open as expected.

Mio Moov 500-Series | How do 1 go from À to B?

2. Select the country

Note: I you only have the maps of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to step 3.

2) Fromihe Destination Search screen, tap ]

The Select a map screen will display. b) Select USA from the list. The Destination Search screen will display.

3. Search for the City/Area

2) Fromthe Destination Search screen, tap City/Area.

The Keyboard screen will display. b) Use the Keyboard screen to search for New York as the city or area of your destination, then tap the search result. The Destination Search screen will display. eu York Go to Center Chy/ares

4. Search for the street name and house number

2) Fromthe Destination Search screen, tap Street Address

The Keyboard screen will display.

Mio Moov 500-Series |_How do 1 go from A to 8? Using the Keyboard screen The Keyboard screen will display when you are required to enter text, such as when searching for a street name. Search results will be listed in matching order, with the closest matches appearing at the top of the list. À maximum of 99 results will display. The Keyboard screen can display with various layouts depending on the information you need to enter, including alphabet, number, alternate characters and combinations of these. You can also choose the type of keyboard you prefer from alphabetic, QWERTY and keypad. For more information, see “Keyboard” on page 73. Select a ciy/ares eu Vert — Pnisdelshis v olwlelelr|vjulifolr ALsfofr[c]u]sne x[e[Lvls[Lnu].+ Sara ana Envar the house number. en ere — Go to Center of street — = RES E aëc | Der | 6m | KL TN UN 5 MNO PQRS TU | Wz 6 Z 8 9 0 at 123 Es a | As you select each character, the first two results will display. Tap | à ; then scroll to see more search results. To select a character or a search result, tap the character or search result. = To delete a character, tap

• To display more characters, tap 123, alt or abc, if available. Using the Destination Search screen The Destination Search screen is used to select your destination by area, street, postal or ZIP code, Points of Interest, intersection, city, area, state or country. [ge Got canir ETS As you specify each part of the address, it will display at the top of the screen. The available options will change to reflect the parts of the address stil to be completed.

Mio Moov 500-Series |_How do | go from A to B? b) Use the Keyboard screen to enter Mio Avenue as the street name of your destination, then tap the search result. Note: There may be mulliple matches for a particular street name. Long streets that run through several neighbouring areas, and common street names wil produce search results ordered by their city or area name. Enter the house number Go to Center of Street 1-37, (dd) c) Use the Keyboard screen Lo enter 118 as the house number of your destination, then tap the search result. The Preview screen will display. Note: If house numbers ar lab, but not ihe one {hat you require, you may have lo choose {he same street in à neighbouring area. Press RS and select another search resuit Ihouse numbers are not available for your selected section of Ine street the Preview screen will display.

118 Mo avenue New York, New York 10017 USA d) Complete one ofthe following: If you want to navigate Lo your selected destination Your route is calculated; the 3D Map screen will display. view the position on the map screen tap the map to display the position on the 2D Map screen view more information about your tep More destination The Destination Details screen will display. add the destination to a multk-Stop tp | tap Add The Muït-stop Tip Planner screen will display. The address is listed 25 a waypoint on {he mulli-stop trip. See “How do | create à tip with multiple s10ps7" on page 20 save the destination as My Home * tpsave The New Favorite screen will display. *___tep Save as My Home. save the destination as a favorite * tpsave The New Favorite screen will display. *__tep Save as Favorite

Mio Moov 500-Series |_How do 1 go from A to 8? How do I create a trip with multiple stops? You can use the Mult-stop Trip Planner screen to set multiple stops or waypoints for your tip. Your route will be calculated to go via each of these points in the specified order. Waypoints can be added via the Mult-stop Trip P lanner screen or by selecting Location, then Add to Trip from the pop-up Map menu on the 2D Map or 3D Map screen. You can save up to 198 multi-stop trips, each with up to 14 waypoints. Note: Waypoints added, updated or deleted after a mult-stop trip has commenced will not affect Ine current route. Quick Steps

1. Start your Multi-stop trip

Select the country Search for the city/area Search for the street and house number u 8 w N Add additional waypoints

C4 Case Study: How do I navigate to multiple addresses? This case study will show you how to set a multi-stop trip by entering multiple waypoints. The address we will be using in this example is: Note: The below address is fictilious and used as an example on. 671 Mio Avenue New York New York 10036 USA. Tip: Before you enter your destination address, ensure {hat you have set your route preferences, For more information, see “Route Options” on page 55.

1. Open your Muiti-stop Trip screen

@ y Current Location The Mult-stop Trip Planner screen wil display.

Mio Moov 500-Series |_How do | go from A to B?

The Add to Trip Menu wil display. Add To Trip = b) TapAddress The Destination Search screen will open. Note: You can also add waypoints using favoris, recent destinations and POI locations,

2. Select the country

Note: I you only have the maps of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to step 3. a) | Fromihe Destination Search screen, tap [ME] The Select a map screen will display. b) Select USA from the list. The Destination Search screen wil display.

3. Search for the City/Area

2) Fromthe Destination Search screen, tap City/Area.

The Keyboard screen will display. b) Use the Keyboard screen to search for New York as the city or area of your destination, then tap the search result. The Destination Search screen will display. eu York Go te Center Ciy/ares LG. set dm

Mio Moov 500-Series |_How do 1 go from A to 8?

4. Search for the street name and house number

2) Fromthe Destination Search screen, tap Street Address

The Keyboard screen will display. Select a street mo Ave — Broschay 2 a[wle[r[r[v[ul1lo[r als/o/r{clulalklr z|x[e[v[s[n]u] + CN «| - [152 b) Use the Keyboard screen Lo enter Mio Avenue as the street name of your destination, then tap the search result. Note: There may be mulliple matches for a particular street name. Long streets that run through several neighbouring areas, and common street names wil produce search results ordered by their city or area name. Enter the house number Go to Center of Street 1:37, (Odé) DEEE

c) Use the Keyboard screen Lo enter 671 as the house number of your destination. The Preview screen will display. en |<>

Note: I house numbers are available, but not that you require, you may have to choose the same street in a neighbouring area. Ifhouse numbers are not available for your selected section of the street the Destination Preview screen will display. € Recent Location d) TapAdd. The waypoint is automatically saved and the Mult-stop-Trip screen will display. 1 14y Current Location + 118 Mo venue, New York, New Vor + 3 Columbus Circle (Broadway), New 44 Columbus Avenue, New York, New

Mio Moov 500-Series |_How do 1 go from A to

€) Complete one or more of the following: H you wantto . Then add another waypoint Note: Waypoints added after a mult-stop rip has commenced wil not be included in the current route. - tpAdd The Add To Trip Menu will display - retum to step ta navigale Lo your selected destination tap The Preview screen will display. tap The 3D Map screen wil display the calculated route. change the order of your waypoints + {ap a destialion point to move The Preview screen will display. + tapUpor Down The Mult-Stop Tip Planner screen wil redisplay. delete all waypoints tap Clear. delete one waypoint + {ap a destinalion point t delete. The Preview screen will display. + tap Delete. The Mult-stop Trip Planner screen vil redisplay. save the multi-stop tip as a favorite F mpsae The New Favorite screen will display, + tp Save as Favorite. The Favorite will be saved.

Mio Moov 500-Series |_How do 1 go from A to 8? How do 1 skip a waypoint during a multi-stop trip? To skip a waypoint during a multi-Stop trip, complete the following:

2. Tap Route, then Skip Waypoint.

The next waypoint will be skipped and the route recalculated to the following waypoint.

Mio Moov 500-Series |_How do | go from A to B? How do I search for a Point of Interest (POI)? A POI is a named site, feature, landmark or public venue which can be displayed as an icon on the map. POIS are grouped by type, such as gas stations, parks, beaches and museums. Select a POI using the Destination Search, Keyboard and Preview screens, which used together form a POI-entry wizard. Tip: You can also quickly search for certain POI based upon our current location via the Main Menu screen. This section provides a case study to help guide you through finding or setting your POI as a destination. Quick Steps

3. Search for the City/Area

T4 Case Study: How do I search for a Point of Interest? This case study will show you how to enter an address and navigate Lo it. The address used in this example is: Note: The below address is fictilious and used as an example on. Statue of Liberty New York New York 10004 USA Open the Destination Search screen En > The Destination Search screen will display. Note: If {his is the first time you are setting your destination and you have maps from more than one country installed, then the Select a map screen wil display instead of the Destination Search screen. Ga direct to step 2b. The next time you perform this procedure, Ihe Destination Search screen wall open as expected.

Mio Moov 500-Series |_How do 1 go from A to 8?

2. Select the country

Note: I you only have the maps of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to step 3. a) | Fromihe Destination Search screen, tap [ME] The Select a map screen will display. b) Select USA from the list. The Destination Search screen will display.

3- Search for the city/area

2) Fromthe Destination Search screen, tap City/Area.

The Keyboard screen will display. b) Use the Keyboard screen to search for New York as the city or area of your destination, then tap the search result The Select POI Category screen will display Select POI Category Tip: The list of categories is divided into Enabled Categories which are set lo display an icon on he map screens, and Olher POI Categories which wil not display an icon

Mio Moov 500-Series |_How do | go from A to B?

Either tap Search by name to search in all POI categories, or select a category from the list. The Keyboard screen will display. The Preview screen will display. Use the Keyboard screen to search for Statue of Liberty as your destination, then tap the search result. Statue of Liberty Monument New York, New York 10004, USA a Destination Preview Complete one of the following: H you want to … Then … navigate Lo your selected destination

Your route is calculated and displayed on he 3D Map screen. view your position on the map screen tap the map to display the position on the 2D Map screen. view more information about your destination tap More. The Destination Details screen will display. add the destination Lo a muli-stop trip tep Add The Mul-stop Trip Planner screen wil display. The address is listed as a waypoint on the mult-top trip. See “How do 1 create trip with multiple stops?” on page 20. save the destination as My Home + tpsave ‘The New Favorite screen wil display.

• __tap Save as My Home. save the destination as a Favorite + psave ‘The New Favorite screen wil display. " __tap Save as Favorite

Mio Moov 500-Series |_How do 1 save Favorites and My Home? How do I save Favorites and My Home? You can save up to 200 destinations as favorites, one of which can be saved as My Home. You can save a favorite from the Preview screen after searching for an address, or from the Map Menu on the 3D or 2D Map screens. For more information, see “How do | use the Map Menu?" on page 43. How do I save a Favorite or My Home?

1. Search for an address until he Preview screen is displayed

3. To change the name of the favorite, tap

4. After you have entered a name for the favori, tap DS

The New Favorite screen will display.

5. Complete one of the following:

H you wantto … |Then. save 28 a Favorite | ap Save as Favorite. The favorite is saved. The Preview screen wi display. save as MyHome | tap Save as My Home. The favorite is Saved as My Home. The Preview screen will display.

Mio Moov 500-Series |_How do 1 save Favorites and My Home? How do | navigate to a Favorite?

1. Tap the Favorite destination you want to travel to.

The Preview screen wil display. Favorite Previen 7

Your Mio will calculate the route from your current location. The 3D Map screen will display. How do | navigate to My Home? If you have not set an address as My Home, the first lime you try to navigate to My Home you will be prompted to search for an address using the address-entry wizard. Option 1 - Via the Main Menu En > © Your Mio will calculate the route from your current location. The 3D Map screen will display. Option 2 - Via the Favorite Destinations screen EN > Q

1. From the Favorite Destinations screen, select My Home.

The Preview screen will display.

Your Mio will calculate the route from your current location. The 3D Map screen will display.

Mio Moov 500-Series |_How do 1 save Favorites and My Home? How do | edit the name of a Favorite? mu > Y

1. From the Favorite Destinations screen, select a favorite to edit.

4... After you have edited the favorite name, ta The Edit Name screen will display.

5. Complete one of the following:

If you want to … Then … rename the Favorile tap Save. ‘The favorite is saved. The Favorite Preview screen will display. save as My Home tep Save as My Home. The favorie is saved as My Home. The My Home Preview screen wi display.

Mio Moov 500-Series |_How do 1 save Favorites and My Home? How do I delete a Favorite? EI > @

1. From the Favorite Destinations screen, select a favorite to delete.

‘The favorite is deleted. The Favorite Destinations screen wil display.

Mio Moov 500-Series |_How do | navigate to a recent location? How do I navigate to a recent location? To make navigating to an address easier, your Mio will automatically save all your start locations and destinations in a list of recent locations.

IG 6635 West Drive, Ne Vorh New Von. Penn Station AG 220 Philios Avenue, South Hacker. AD 671 th Avenue, he York, AG 667 10th avenue, New York, New Yor

Recent Location Complete one of the following: If you want to … calculate the route and open the 3D Map screen Tap The 3D Map screen wil display: view the full address details of the recent location tap More. The Recent Destination Details screen wil display. save the recent location as My Home + tapSave. The New Favorite screen wil display. *__tap Save as My Home. save the recent location as a favorite + tapSave. The New Favorite screen will display. *___tap Save as Favorite

Mio Moov 500-Sei s | How do ! view my route? How do 1 view my route? When a route has been calculated, the 3D Map screen wil display. You will be directed to your destination by spoken and visual instructions. The Map button cycles through the 3D Map, 2D Map, Traffic Overview, Route Overview and Tum-by-Tum” screens. 3D Map screen ‘The 3D Map screen displays your current position and follows your direction of travel. “_ Tap and drag the screen, to move across the map. = Tapthe map to viewthe Map Menu (see “How do | use the Map Menu?" on page 43). Note: Depending on the country you are traveling in, the color of the direction and distance buttons may differ from the above example: Item Description Next instruction The direction and name of the street lo turn in to. irection and The direction and distance to your next turn. distance of nexttum Note: To repeat the spoken prompt of your next turn, ap the turn arrow: Route Your current route is highlighted. Current position 4 Your current position is marked with. Speed indicator Displays when you exceed your set speed limit. For more information, see "Driver Alerts 3/4” on page 57. CIEL Displays one of he following, = The name oflhe street you are located on “Speed wamings "Active POIs. Tap to display the Main Menu screen. Note: The Status Bar is replaced by current Traffic events, when Traffic is enabled. For more information, see “Traffic” on page 48. Main Menu The Main Menu bution allows you to enter an address for your destination, customize preferences and receive updated traffic information. Distance and Time Information ap to expand and see the following options: "Time = kmhor mph (Speed) " TTG (Time to Go)

• DTG (Distance to Go)

• ETA(Estimated Time of Arrival). TTap to cycle through the options.

Mio Moov 500-Se: s |_ How do ! view my route? Item Description LH RES Cancels your eurrent route. Lo] Zoom C\ To view 00m options, tap LS. + Tozcomout wep LES) *___ro200mn, pl) Map The Map button allows you to cycle through different map screens. Mute/unmute volume, TE en TMC, battery, GPS | Tapl Lo expand and see the following options: and compass information. Mutelunmute volume Hé Sierre aus nocator For more nomaton, see “Ho does my Mo receive traffic information?” on page 48. DM 5107 charge indicator GPS status indicator ‘The icon displays green when a GPS fix is established and red when a GPS fix is unavalable. To indicate the reception strength of a GPS fix belween one and four green vertical bars are displayed. ŒS cvs

Mio Moov 500-Sei s | How do ! view my route? 2D Map screen ‘The 2D Map screen shows your current position (if a GPS fix is active) and surrounding street names. If a route has been calculated, the route and turns are highlighted. The 2D Map screen follows your direction of travel unless the Map Display preference is set to North (see ‘Map Display” page 60). “_ Tap and drag the screen, to move across the map. = Tapthe map, to view the Map Menu (see "How do | use the Map Menu?" on page 48) Note: Depending on the country you are traveling in, the color of the direction and distance buttons may differ from the above example: Item Description D cr ‘The direction and name of the street lo turn in to. Direction and The direction and distance of your next turn. distance of next tum Not o repeat the spoken prompt of your next turn, tap the turn arrow: Route Your current route is highighted Current position 4 Your current position is marked with. CIET Displays one of ie follouing = The name oflhe street you are located on “Speed wamings "Active POIs. Tap to display the Main Menu screen. Note: The Status Bar is replaced by current Traffic events, when Traffic is enabled. For more information, see “Traffic” on page 48. Main Menu The Main Menu button allows you to enter an address for your destination, customize preferences and receive updated traffic information. Distance and Time | Tap lo expand and see the following options: Information Time = kmhor mph (Speed) " TTG (Time to Go)

• DTG (Distance to Go)

• ETA(Estimated Time of Arrival). TTap to cycle through the options. ER | cancel route Cances your current route BD [a] To view zoom options, tap

Mio Moov 500-Series |_How do 1 view my route? Item Description Map The Map button allows you to cycle through different map screens. En] Mute/unmute volume, É TMC, battery, GPS | Tapl Lo expand and see the following options: and compas ns ER urrerun ESS 7Sraf stus ndcator For mor information, se “How does my Mio receive traffic information?” on page 48. DM Eater charge inaicator ÉD GPS sets nacar L The icon displays green when a GPS fi is established and red when a GPS fe is unavailable. To indicate the receplion strength of a GPS fix between one and four green verlical bars are displayed. De Compass indicator

Mio Moov 500-Series |_How do | view my route? Traffic Overview screen Depending on your Mio model traffic information may not be available or may require a traffic antenna, ‘The Traffic Overview screen displays a general overview of the traffic situation on your route, including all events in the immediate vicinity. “_ Tap and drag the screen, to move across the map. = Tapthe map, to view the Map Menu (see “How do | use Map Menu?" on page 43) Item Description Eventicon Displays icon to indicate type of event Current position L Your current position is marked with Your final destination. EE Tap to display the Event List screen. Status bar Displays one of the following

• The name ofthe street you are located on "Speed wamings - Active POIs. Tap to display the Main Menu screen. Note: The Status Bar is replaced by current Traffic events, when Traffic is enabled. For more information, see “Traffic” on page 48. Tap to display the Traffic System Status screen. Cancel route Cancels your current route. Zoom al To view zoom options, tap LS!

Mio Moov 500-Se: s |_ How do ! view my route? Item Description Mute/unmute voeu, | rap EI expand an see me iotoung options battery, GPS and compas [eo Mute/unmute volume information. TMC ratfic status indicator. For more information, see ‘How does my Mio receive traffic information?” on page 48. DM 5247 cac ndicator GPS status indicator The icon displays green when a GPS fix is established and red when a GPS fix is unavallable. To indicate the reception strength of a GPS fix belween one and four green vertical bars are displayed. Compass indicator

Mio Moov 500-Sei s | How do ! view my route? Route Overview screen The Route Overview screen gives you a bird's eye view of your tip. Note: À roule must first have been calculated for this screen Lo be available. Tap and drag the screen, lo move across the map. Tap the map to view the Map Menu (see “How do | use the Map Menu?" on page 43). Note: Depending on the country you are traveling in, the color of the direction and distance buttons may differ from the above example: Item Description Next instruction ‘The direction and name of the street lo turn in to. Not o repeat the spoken prompt of your next turn, tap the turn arrow: ‘The direction and distance of your next turn. Not o repeat the spoken prompt of your next turn, tap the turn arrow:

Your current route is highlighted Current position Your current position is marked with“ i visible.

Your final destination. 6 96 Qq Scale bar Displays map scale. Main Menu The Main Menu button allows you to enter an address for your destination, customize preferences and receive updated traffic information. Status bar Displays one of the following = The name oflhe street you are located on “Speed wamings "Active POIs. Tap to display the Main Menu screen. Note: The Status Bar is replaced by current Traffic events, when Traffic is enabled. For more information, see “Traffic” on page 48. istance and Time Information Tap lo expand and see the following options: "Time = kmhor mph (Speed) " TTG (Time to Go)

• DTG (Distance to Go)

• ETA(Estimated Time of Arrival). TTap to cycle through the options.

Mio Moov 500-Se: s |_ How do ! view my route? Item Description Fo] Cancel route Cancels your current route. En] Zoom C\ To view 200m pions, tp [A] + Tozomout, tp LE . To zoom in, tap (&] Map The Map buton alous you to cycle Erough dirt map screens Mutejunmute Volume, TMC, op BI 1» cxpand and see ie tolowing options: battery, GPS and compass sn Mutelunmute volume information. sé TMC traffic status indicator. For more information, see “How does my Mio feceNe ai inomation?" on page 48 DS ae care nacaor en ss neo The ion dplayesrcen uhen a GPS fi established and re when a GPS fx is unavalabl. Ÿo naicate the receptor srengi of à GPS fx beteen one and four green vertical bars are displayed De Compass indicator

Mio Moov 500-Series |_How do | view my route? Turn-by-Turn screen The Tur-by-Tum screen displays the next four turns of your route, the turn direction, the street name and the distance to the turn. You can view all the turns in the list, Using the up and down arrows. À route must first have been calculated for this screen to be available. Note: À roule must first have been calculated for this screen Lo be available.

Note: Depending on the country you are traveling in, the color of the direction and distance buttons may differ from the above example: Item Description Direction ofturn ‘The direction of the ur. Your next turn is highlighted! Note: To Repeat the spoken prompt of your next tu, tap the turn arrow. ‘The direction and distance of upcoming turns. Distance totum | The distance lo your next um. Yournex um is highighted instruction The direction and name of he street o tu in to. Your next tum is ighlighted

Nexttum Your next lu is at the Lop of the it

Main Menu The Main Menu button allows you to enter an address for your destination, customize preferences and receive updated traffic information Status bar Displays one of he following; “The name ofthe street you are located on “Speed wamings “Active POIs. Tap to display the Main Menu screen. Note: The Status Bar is replaced by current Traffic events, when Traffic is enabled. For more information, see “Traffic” on page 48. Distance and Time Tap to expand and see the following options: Information "Time

• km or mph (Speed) + TTG (Time to Go) + DTG (Distance to Go) + ETA (Estimated Time of Arrval). Tap to cycle through ne options. Scroll buttons Alow you to view each tum by moving up and down through the list Map The Map button allows you lo cycle through different map screens.

Mio Moov 500-Se: s |_ How do ! view my route? Item Description Matejunmute Veume, TM, rep RM > xp and see ie totouing oprons battery, GPS and ompass information. [eo Mute/unmute volume HS Crafe saus naator For more niomaton, see “Ho does my Mo receive rai information?” on page 48 DM 2107 charge indicator ÉS ssss ru L ‘The icon displays green when a GPS fi is established and red when a GPS fx is unavailable. To indicate the reception strength of a GPS fix between ane and four green vertical bars are displayed ŒS cs

Mio Moov 500-Sei s | How do ! view my route? How do Il use the Map Menu? The Map Menu allows you to access navigational functions from the 3D Map and 2D Map screens. Navigate To Show Details earest POI Avoïd re À ac to Trip | route Displaying the Map Menu

1. Tap (©) t display the 3D Map or 2D Map screen.

2. Tap and drag to move around the map to your selected location.

The Map Menu will display. Map Menu options The following options are available via the Map Menu: Menu Option Description Navigate To Calculates a route from your current location, if your Mio has a GPS fix. Show Details Displays the P review screen from where you can: "View details of the location = Add he location Lo your mulli-stop trip "Save the location as a favorite " Navigate lo the location Note: Irthe cross-hairs are positioned over a traffic event, Show Details will instead display the Traffic Event Details screen. For more information, see "How do | view the Event Details screen?" on page 50. Nearest POI Displays the Select POI further information, see page 25. ategory screen. Select the Category then Search for a POI to navigate to. For {ow do 1 search for a Point of Interest?" on Avoid Area Allous you lo add an Avoid Area by tapping and dragging the map. Un-Avoid Area Deletes the selected Avoid Area. Add to Trip Adds he location to your multi-stop trip. Route Displays the Route sub-menu from where you can:

• Setas Start Sets the location as your departure point + Demonstrate. Staris ihe route demonstration, demonstrating navigation from your current position or departure point. + Stop Demonstration. Slops the route demonstration = Skip Waypoint Skips the next stop on your mull-Stop trip. = Show Summary. Displays à summary of your route, including your departure and destination addresses, total distance and total estimated time Lo your destination *_ Detour. Detours your route to avoid the next 1, 2, 5, 10 or 20 kilometers or the next 1, 2, 5, 10 or 20 miles.

Mio Moov 500-Series |_How do 1 view my route? How do | avoid an area? Your Mio can calculate a route that avoids a specified area on the map. Avoid Areas are displayed as shaded areas. CAUTION If no altemalive route around an Avoid Area exists, lhe route calculation will fil CAUTION If your destination is in an Avoid Area, you wil be routed into that Avoid Area. How do I add an Avoïd Area?

1. Tapthe 3D Map or 2D Map screen to display the Map Menu.

2. Select Add Avoid Area.

3. Tap and drag to set the Avoid Area to the correct size and position.

The Avoid Area is added. How: do I delete an Avoïd Area?

1. Find the Avoid Area that you want to delete.

2. Tap the Avoid Area to display the Map Menu.

3. Select Un-Avoid Area.

The Avoid Area is deleted. How: do I delete all Avoid Areas?

1. Tap Delete Avoid Areas.

2. When the Caution dialog-box opens, tap Yes to confirm.

All Avoid Areas are permanentlÿ deleted

Mio Moov 500-Series |_How do | preview a route? How do Î preview a route? Route demonstration allows you to: = Preview a route. = Plan and view a route without a GPS fix, such as when you are inside a building. The following steps will show you how Lo preview one route.

1. Select a departure point

If you have a GPS fix, you do not need to select a departure point unless you want the demonstrated route to start elsewhere

2) Tap the 3D Map or 2D Map screen at your departure point.

The Map Menu will display. b)_ Tap Route. The Route submenu will display. c) Tap SetAs Start. The Map Menu will close, and the selected point is set as your departure point.

2. Select a destination point

Set a destination either by using the address entry wizard or by using the Map Menu: a) Locate your destination. b) … Tap your destination to display the Map Menu €) Tap Navigate To. The Map Menu will close and the map screen will display the calculated route.

3. Demonstrate the route

Once the route has been determined, you can demonstrate the route by completing the following:

2) Tap the map screen to display the Map Menu.

b) _ Tap Route. The Route submenu will display. €) Tap Demonstrate. The 3D Map screen wil display the calculated route in Route Demonstration mode.

Mio Moov 500-Series |_How do 1 view my route statistics? How do I view my route statistics? The Mio provides information on your: . distance traveled “average speed “maximum speed “time taken fortrip “ stationarytime. Trip information is presented in two different ways. These a “information for the current trip “information for all trips to date, or since the tripmeter was last reset. How do I view statistics on my current route? The Tripmeter - Current Route screen is used to view statistical information for your current trip. a) Press and hold the Information button. The Tripmeter - Current Route screen will display. Stationary Time (os) b) Complete one of the following: I you wantto … Then … eu states fr out | ip BE depay ie rrmetar ia acren rate pme T upReE “ tap Yes toreset ‘The Tripmeter - Current Route screen will display.

Mio Moov 500-Series |_How do 1 view my route statistics? How do! view statistics of my trips to date? The Tripmeter - Global screen is used to view statistical information for all of your trips to date, or since the trip meter was last reset. a) Fromthe Tripmeter - Current Route screen, tap The Tripmeter - Global screen will display. FTripmeter: Global Distance b) Complete one of the following: If you wantto … Then … view statistics for your current route Lo display the Tripmeter - Current Route screen. reset the tipmeter * tepReset A Warning dialog box will display. “ tap Yes toreset The Tripmeter - Global screen wil display.

Mio Moov 500-Series |_Traffic Traffi Trai forma only available on some models and in selected countries Your Mio can receive current traffic information for all main roads and freeways, enabling you to avoid potential delays on your route. Event messages and traffic icons will display as they occur. f an event message obscures your current location, the map will adjust to display both the message and your location. How does my Mio receive traffic information? You can receive current traffic information on your Mio via the built-in antenna using the Traffic Message Channel (TMC) service. The TMC service is by subscription. ‘The Traffic Message Channel (TMC) broadcasts real-time traffic information via the FM Radio Data System (RDS) FM radio stations transmit TMC data on a cycle of several minutes, with hundreds of events able to be broadcast to TMC receivers, such as the Mio Traffic module. Note: To receive TMC information, your Mio must be connected to the in-car charger. Traffic status Your current traffic status is indicated by the color of the TMC icon. To view your current traffic status from the map screens, tap (ME and then tap (HE The following table describes the three traffic status icons: Traffic Status | Description ‘The TMC status is 2 traffic is current} inactive due to one of the following conditions: = Your Mio or Traffic module is connecting to the TMC service.

• Your Mio or Traffic module cannot receive TMC data. This may be due to poor radio coverage in the local vicinity. "You are in a region hat is not supported by the Mio Traffic module. ap to display he Trafic Overview screen. ‘The TMC status is orange if one of the following conditions apply:

• You have navigated into a region that is not supported by Mio Traffic, but there are stl trafic events listed on the Event List screen

• You have separated your Mio from the Mio Traffic module, or the Mio Traffic module is not receiving power but there are stil traffic events listed on the Event List screen. ap to display the Trafic Overview screen. ES The TMC status is green if your Mio or Traffic module is active and receiving traffic events. Tap to display he Trafic Overview screen. Your traffic status is displayed in more detail on the Traffic System Status screen.

Mio Moov 500-Series |_Traffic How will ! know when a Traffic Event occurs? Incoming events are handied according to your Traffic preferences. For more information, see “How do | customize Traffic preferences?" on page 63. When traveling through an area in which you can receive traffic status, your Mio will decode these events and display them on-screen. An icon will display at the event location on the map screens, and an audible warning is given if an event is on your route. Where the extent of an event is a specific distance, the road will be highlighted and arrows will indicate the direction affected. A message will display at the bottom of the screen with the road name, the section of road affected and the type of event that has occurred. The message remains on screen for 8 seconds and is added to the Event List.

Mio Moov 500-Se: s | Traffic How do I view a list of all events on my route? Your Mio creates a list of events as they are received, which is displayed on the Event List screen. This screen can only be viewed if the TMC icon is green or orange. From the Traffic Overview screen, tap BL==b) Ce] Alone ous La] DER Éscot Teva 0 three Lanes blocked 6] us 101 Southbound Lucas Valley Rd/Smith Ranch R4 > Sir Francis … | || 2 Au se ETES — Element Description Event description | Displays details of the Event, including: + Name of road and direction in which Event is taking place. + Location of where Event begins and ends. > indicates an Event from a location, to a location < indicates an Event between locations. “Type of Event. Eventicon Displays icon to indicate type of event. See page 100 o view ist of icons. EE ap Lo return to the previous screen. Tap to display the Select event sorting type screen, were you can sort events by distance, road name or age. Position indicator | Displays your position in the Event List screen. Scroll buttons Alow you to view all events by moving up and down through the list 60 S900 Eventnumber | Displays the number of events in current ist

Mio Moov 500-Series |_Traffic How do | view traffic details? There are several ways to view di Choose one of the following: etails of an event received by your Mio. Location Option your route From any of the screens used lo view |* laplhe Even! message when il appears on screen. The Event Details screen wil display. From the Traffic Overview screen

The Event List screen will display. + Select and tap the event you want to view The Event Details screen wil display. From ihe Map Menu + Tap and hold the traffic icon, which displays aline location of the event. The Map View menu will display. + Tap Show Details. The Event Details screen wil display.

pre due Lex] L] Feu etour 0.6 mi longer Element Description D ec Displays Event details, including

• Time Event was received, or last updated
• Name of road on which Event is taking place.
• Location of where Event begins and ends. > indicates an Event from a location, to a location. < indicates an Event belween locations. -__ TypeofEvent Eventicon Displays icon to indicate type of Event. Detour information Displays details of detour recommendation, if any. For more information, see How do 1 know if a detour is recommended?" on page 51 Tap to return to the previous screen. + Tap Alto view next Eventin list + Tap Dlio view previous Event in list Event number Displays the number of the event current displayed and the total number of events in the list Tap Lo iniiate a new route Lo avoid the event.
• Only available if a detour or re-route is available. Note: Un-avoid area is represented by calculated and is displayed when a re-route has been

Mio Moov 500-Series |_Traffic How do | know if a detour is recommended? When a Traffic or Clearance event occurs on your route, a detour will always be recommended. The detour event message will display in the status bar on map screens. Note: Detours are only recommended for Trafic or Clearance Events on a calculated route How do I avoid an event on my route? From the Trafic Overview screen, tap BL-=B

1. From the Event List screen, tap the event.

The Event Details screen will display. 2 If a detour has been calculated to avoid an event on your route, route and avoid the event. The 3D Map screen will display. is available; tap to accept the new How do 1 cancel a detour around an event on my route? If you have chosen to avoid an event and a new route has been calculated, you can cancel the detour around the event and return to your original route.

1. From the Event List screen, tap the Event you want to un-avoid.

The Event Details screen will display.

2. Re-route information displays at the bottom of the screen.

+ fa re-route has been calculated, BE à available: tap to accept the new route. The 3D Map screen wil display. How do 1 automatically avoid all traffic and clearance events on my route? To automatically avoid all traffic and clearance events see Traffic preferences on page 68.

Mio Moov 500-Series |_Traffic Traffic Messages The Event Details screen displays detour status information Detour Not Avail Ifa detour is not available, one of the following messages will display: Message Description This Event is not locatable AA specific location for the Event cannot be identified. This clearance is not locatable This Event does not affect your route The Event is not on the current leg of your journey, or is behind your current position. This clearance does not affect your route You are avoiding this Event The Eventis not on the current leg of your jourey. You have accepted this clearance You are 100 distant 10 re-route The Event is current too distant 10 affect your journey. You are t00 distant to accept this clearance Detour not found A detour / re-route could not be calculated. Clearance route not found Detour recommended messages If a detour is recommended, one of the following messages wil display: Message Description Finding detour. Your Mo is calculating a new route. During calculation, the % complete will display. Recalculating route. Note: Exiing this screen before {he new route is calculated will cancel {he operation Detour distance. À detour has been calculated The difference between Ine distance of your current route and he proposed roule is displayed Clearance change

Mio Moov 500-Series |_What can | customize? What can ! customize? There are various customization options available to enhance your navigation experience. ‘The Preferences menu screens are accessed by pressing EARIRARESE- Route Options Language pen ui Ki D = To revisit the previous screen, tap

Mio Moov 500-Series |_What can | customize? Route Options You can enhance your navigation experience by modifying aspects of your route and route calculation. Route Calculation 1/4 à > æ Route Type Shortest distance Fastet time Complete the following If you want to. Then. change 1he route type move the Route Type slider towards Fastest time to give high prionty Lo {ne fastest lime when calculating a route move the Route Type slider towards Shortest distance Lo give high priority to the shortest distance when calculating à route. Note: Changing shortest distance over faster lime can cause much longer jourey lime change the preference for reeways | move the Preference for Freeways slider towards Less often to use roads other than freeways were possible when calculating a route. Note: This option may not completely remove Freeways from a route. move the Preference for Freeways slider towards More often Lo use freeways where possible when caleulating a route. = Your preferences are automatically saved.

Mio Moov 500-Se: s |_What can | customize? Road Types 2/4 3 #> Eu Select your routing preferences for the following road types: Auot Warn Toll ronds D & Unsesed ronds 8 & Ferry routes 8 & K Rond Types 2/4 > Complete the following H you want to. Then. avoid tol roads receive a warning if your route includes. toll roads. select the Toll roads check box in the Avoid column. select the Toll roads check box in the Wam column, The waming wil display at the start of every trip containing a tol road avoid unsealed roads receive a warning if your route includes. unsealed roads select ihe Unsealed roads check box in the Avoid column. select the Unsealed roads check box in the Warn column. The warning will display at the Start of every trip containing unsealed roads. avoid ferry routes receive a warning if your route includes. ferry routes select the Ferry routes check box in the Avoid column Note: Selecting Ferry routes does not allow you Lo travel between continents or even countries. select ihe Ferry routes check box in the Warn column. The warning wil display at the start of every trip containing ferry routes. = Your preferences are automatically saved.

Moov 500-Series |_What can | customize? Driver Alerts 3/4 > > > 0 > ME Des Mers Mar me not to operate my Mio while drving 2 Art me vien my speed exceeds Complete the following If you want to. Then enable a visual waming if the Main Menu select the Warn me not to operate my screen is accessed in à moving vehicle driving check box. enable a waming chime when traveling at or _ | select the Alert me when my speed exceeds check box above a designated sf select your preferred speed Select your preferred speed from the Speed box = Your preferences are automatically saved.

Mio Moov 500-Series |_What can | customize? Data Recording 4/4 3 > € > EN > SN > M GPS Logging 7 snabie GPS data ogging Complete the following If you want to... Then. record a GPS log of select the Enable GPS data logging check box your tips = Your preferences are automalically saved.

Mio Moov 500-Series |_What can | customize? Map Display You can change the look and behaviour of the Map screens by customizing the Map Display preferences. Map Display 1/3

pme @ au cay/nignt © nine Complete the following If you wantto... Then... change the map color scheme Select your preferred scheme from the Map Scheme box. set the screen contrast lo automatically adjust | select the Auto day/night option improve screen contrast in light or dark select either the Day or the conditions ght option to manually acjust ine contrast. = Your preferences are automatically saved.

Mio Moov 500-Se: s |_What can | customize? Map Display 2/3 > Ÿ > Map Presentation (7 Auto-200m on Main Map screens 7 Keep North at top of 20 Map screen {2 show no-entry road signs Complete the following If you wantto. Then... enable automatic zo0ming during navigation select ihe Auto-zo0m on main map screens check box. If selected, Ine 3D Map screen will automaticaly z00m in or out, depending on your speed, to allow optimal vieing of your route. display North at the top of the 2D Map select the Keep North attop of 2D Map screen check box. Note: If not selected, the direction you are traveling in wil display at the top of the 2D Map screen display “no entry” icons on “no entry” roads on the 2D Map and 3D Map screens select the Show no-entry road signs check box = Your preferences are automatically saved.

Mio Moov 500-Series |_What can | customize? Select Map 3/3 > Ÿ> NE > EE Complete the following If you want to. Then. use maps from a different continent | select a different continent from the maps you are currently using. When selected, the maps for the new continent wil load and the 3D Map screen will display. = Your preferences are automatically saved.

Mio Moov 500-Series |_What can | customize? Map POIs Points of Interest (POIS) are grouped into categories. You may choose to either display (or hide) icons of all POI categories on the map screens, or only display the icons from selected categories. For example, you may only be interested in entertainment venues and want to disable other categories such as schools.

CES D 0 side J ‘Turm All On f ‘Turn Al Off Complete the following If you want to. Then... display all POI icons (ie, icons from al categories) | Tap Turn All On display no POI icons Tap Turn AI Off. select a specific POI category icon for display on the | select the required POI category checkbox; map screens repeat until al required categories are selected. = Your preferences are automatically saved.

Moov 500-Series |_What can | customize? Volume > 4 [ass | Low Win

7 speak hesboaré letters a Volume Complete the following If you want to. Then. increase or decrease the volume move the Volume slider towards High lo increase the volume: move the Volume slider towards Low lo decrease the volume. hear a tone when you tap the touch | select the Audio check box: screen hear keyboard characters spoken to | select the Speak keyboard letters check box. you = Your preferences are automatically saved.

Screen Brighiness: Night Dim Bright Complete the following If you want to. Then. change the screen brighiness | move the Screen Brightness slider towards Bright to increase screen brighiness. move the Screen Brightness slider towards Dim to decrease screen brighiness.

Warning: Your Mio can heat up when the Brightness scale is set above 70% - .e., when more

{han seven rectangles are colored - Iherefore, use lower brighiness whenever acceptable = Your preferences are automatically saved.

Mio Moov 500-Series |_What can | customize? GPS GPS Status 1/2 Signals are transmitted by Global Positioning System (GPS) satelites orbiting the Earth. The GPS Status screen provides a visual representation of the information being received. Latitude and longitude are displayed, along with ground speed and the heading in degrees. The strength of each satelite is displayed on a bar chart ÿ$ ” En > à The satelites available from your current position are shown as gray, red and green colored bars: Bar color Description No signa. Re À valid signal but not being used 1 fix your position Green À valid signal being used 10 fix your posiion. Resetting your GPS fix Occasionally, the GPS fix may need to be reset. This may occur if the receiver has been transported a long distance Since last being used: for example, to a different country, and is still trying to establish the previous position. Complete the following If you wantto... Then... reset the GPS tep Reset GPS.

© Was (ons railable in USA) © EGNOS (oniy available in Europe) Set GPS Mode 2/2 Complete the following If you want to. Then. use GPS select he Normal option use WAAS Select the WAAS (only available in USA) option. use EGNOS select he EGNOS (only available in Europe) option Note: WAAS - Wide Area Augmentation System is a navigation system developed for civil aviation by the Federal Aviation Administration {FAA), a division of the United States Department of Transportation (DOT) EGNOS - European Geostationary Navigation Overlay Service is a satelite based augmentation system (SBAS) under development by the European Space Agency, lhe European Commission and EUROCONTROL. Tip: You should only change the default seting if you are experiencing poor GPS performance. = Your preferences are automatically saved.

Mio Moov 500-Series |_What can | customize? Language $ > I > oc Gudance QD enable vice guidance Longuage (EE vrais 0 TE) Language Complete the following H you want to. Then. enable voice guidance select the Enable voice guidance check box. change the on-screen language select your preferred language from the Language box and tap Yes. Your language preference is saved and the map screen is displayed. change the voice scheme select your prefered voice scheme from he Voice Gui Note: Only voice schemes that are compatible with the chosen language are displayed jance box. Your preferences are automatically saved.

Mio Moov 500-Series |_What can | customize? Traf: Traffic information is only available on some models and in selected countries You can view your current traffic system status and change options by customizing the traffic preferences. Traffic System Status

From the Traffic Overview screen:

Tuned to Classic on 100.9MHz Preterred Station a Traffle System Stats à ‘The Tuner section displays the name and frequency of the radio station currently being used to receive traffic event information. À bar shows the strength of the traffic signal being received: the more green bars, the stronger the signal. Complete the following If you want to... Then... change your preferred radio station select your prefeed radio station from the Preferred Station dropdown. = Your preferences are automatically saved.

Mio Moov 500-Series |_What can | customize? Traffic Event Notification

From the Traffic Overview screen: (7 Notify me about nearby trafic events (ont notify me about events on my route (7 ont notity me if à detour 5 recommended (C) automatieall accept recommended detours Complete the following H you wantto Then turn on of traffic event notification select the Notify me about nearby traffic events check box lo receive traffic event notification. clear the Notify me about nearby traffic events check box to turn off trafic event notification. Note: Event icons will stil display on the 3D and 2D Map screens. be notied about events that affect your current route select the Only notify me about events on my route check box. be notiied only when a detour is recommended select the Only notify me if a detour is recommended check box automaically accept recommended detours and have a new route calculated select ihe Automatically accept recommended detours check box. “Your preferences are automatically saved

Mio Moov 500-Se: s |_What can | customize? Select event sorting type From the Traffic Overview screen: Sort traffic events by @ sance © Road name

(1 oniy show events on my route Complete one the following: H you wantto sort events by distance select the Distance check box. sort events by road name select the Road name check box. sort events by age select the Age check box only see events that occur on your route select the Only show events on my route check box “Your preferences are automatically saved

Mio Moov 500-Series |_What can | customize? « Power The Battery Status bar shows the percentage of power left in the Mio battery: the words Extemal Power will display when the battery is charging from an external power source. To charge the battery, see "How do | monitor the battery status?" on page 12.

Mio Moov 500-Series |_What can | customize? Keyboard X”Æ>® Keyboard type © Le aiphabetie type (a, b, €.) © Le were Adäress searen () Use keypad type lab, de for address arche Complete the following IH you wantto... Then... use an alphabetic keyboard for entering information | select the Use alphabetic type (a, b, c..) option. use a QWERTY keyboard for entering information | selectine Use QWERTY type option use a keypad-type keyboard (predictive text) when | select the Use keypad type (abc, def..) for address searches check box searching for an address = Your preferences are automatically saved. How does predictive text (abc, def.) work? Predictive text allows addresses to be searched by a single key-press for each letter, as opposed to the multiple key- presses. As you enter a letter of an address, your Mio will compare all possible combinations against the maps you have installed and determine which address you intended to type. For example: To enter London, tap JKL MNO MNO DEF MNO MNO . Your Mio will compare all possible combinations and display London as a search result. You can add further letters to narrow the search.

Units You can change the units used by your Mio by customizing the measurements preferences. Units 1/2 Time Format @ rx © hour sance Unis O metre» klemeters fractional miles rriles and yards Complete the following: DER > KE LA: If you want to... Then... change the time format select either the 12 hour or 24 hour option change the distance units! select your preferred distance unit type from the Distance Units options. = Your preferences are automatically saved. ‘ Only available when AU English, UK English or US English language is selected.

Mio Moov 500-Series |_What can | customize? Units 2/2 % > 0 > EN > Ÿ > Eu Position Format © Decimat degrees © vexrecs. minutes and seconds Complete the following: H you want to … Then … change the latitude, longitude position format select either the Decimal degrees or the Degrees, minutes and seconds option = Your preferences are automalically saved.

Moov 500-Series |_What can | customize? ASareup A show the Tutorial {7 Snow the Language Selection screen Complete the following: H you want to. Then. show the Tutorial when you tum on your Mio select the Show the Tutorial checkbox show the Language Selection screen when you tum on … | select ihe Show the Language Selection screen checkbox your Mio = Your preferences are automatically saved.

Mio Moov 500-Se: s |_What can | customize? Saved Informa SD EX EX Delete Recent Locations Delete Favonte Derinations Deiete avoid ares Restore Factory Defauits Complete the following: f you want to. Then. delete recent locations ‘ap Delete Recent Locations delete favorites ‘ap Delete Favorite Destinations delete avoid areas ap Delete Avoid Areas. restore factory default settings tap Restore Factory Defaults Note: The Restore Factory Defaults option does not delete recent locations or saved favorite destinations. clear all settings: for example, for use in | complete all of the above. a rental car + Whenthe waming dialog box displays, tap Yes.

Mio Moov 500-Series |_What can | customize? Tutorial The Tutorial displays when you turn your Mio on, unless you have cleared the Show tutorial on start-up check box. You can view the Tutorial at any other time: Su > Vielcome to the Mio tutorial TG tutorial wi trou vu the ai opraio of our Mo char ho ta ana Lo your A show tutorat on startup Tutorial: Welcome 1/9 To prevent the Tutorial from displaying again on startup, clear the Show on start-up check box to clear it. = To move forward through the Tutorial screens, tap “To revisitihe previous screen, tap

Mio Moov 500-Series |_What can | customize? About XX” > > 0 This preference contains copyright and trademark information. Shop Demo

SSH >É Complete the following If you want to. Then. enable a shop demonstration of MioMap | ap Shop Demo on the preference screen. Aller a short delay a route demonstration vil 10 be played display.

Moov 500-Series |_What is MioMore Desktop? What is MioMore Desktop? model, certain More Desktop features may not be available. MioMore Desktop is a suite of tools you can use to access greater functionality and product information via your computer. MioMore Desktop allows you to: “obtain software updates “manage maps “manage safety camera subscriptions “manage photos using Photo Album “browse the Mio website for special offers. Can l'use MioMore Desktop with my computer? Ensure your computer has the following minimum system requirements before installing MioMore Desktop:

• IBM compatible PC, = Microsoft® Windows XP SP2 or later (XP MCE, XP x64, Vista x64 not supported), = internet Explorer 6 or higher, = DVDdre, USB port, . Internet connection for activation. Note: For Windows XP users, Microsoft NET 2.0 will be installed on your computer as part of the installation of MioMore Desktop. How do install a map for the first time? ‘The most common task performed using MioMore Desktop is the installation of a new map to your Mio internal memory or memory card. Complete the following procedures: Step Action 1 Install MioMore Desktop on your computer (see "How do install MioMore Desktop onto my computer?" on page 80). 2 Check for software updates for MioMore Desktop on your Mio (see “How do ! keep MioMore Desktop up-to-date?" on page 82). 3 Install one or more maps on your Mio (see "How do | install maps onto my Mio?" on page 84).

Mio Moov 500-Series |_What is MioMore Desktop? How do l install MioMore Desktop onto my computer? Note: Before you begin: Ensure that your computer meels the minimum system requirements for MioMore Desktop, especially: i. Ensure that Intemet Explorer 6 or higher is installed on your computer before you install MioMore Desktop, even if it is not your default browser. ii. Windows XP users, ensure that Windows XP Service Pack 2 or higher has been applied before you install MioMore Desktop.

1. Close all programs on your computer.

2. insert the MioMore Desktop Application Installer DVD into your computer DVD drive.

The MioMore Desktop installer wil start. If your computer does not automatically launch the DVD, start the installation manually: Start > Run. Type DAinstall.exe where *

• is the letter assigned to your DVD drive, then click OK.

3. Select your preferred language for MioMore Desktop.

4. Click Install MioMore Desktop.

5. Follow the screen prompt to install MioMore Desktop:

“Review and accept the License Agreement for MioMore Desktop when prompted. + Select a destination folder for MioMore Desktop when prompted . When the installation has finished, click Finish. MioMore Desktop will open.

6. If prompted to connect your Mio to your computer, complete the following:

“Plug the large end of the USB cable direclly into a USB port on your computer (not a USB hub) and plug the small end into the USB Socket (on the bottom of your Mio. Tip: Where possible, plug ine USB cable into a USB port at the back of your computer.

• Slide the Power switch to the ON position, to turn on your Mio The following screen will display on your Mio.

7. l prompted to update your Mio software, follow the on-screen prompts.

You are now ready to use MioMore Desktop to install maps to your Mio.

Mio Moov 500-Series |_What is MioMore Desktop? MioMore Desktop features

nding on your Mio mod ertain MioMore Desktop features may not be available. Start > AII Programs ® Mio > MioMore Desktop Element Description Menu bar Menus that provide access to basic MioMore Desktop functional. Mio online Displays the Mio website. My Maps Application used to install and manage maps. My Subscription | Information on your current subscripions, including safety camera subscription Photo Album | The sofiware enables you to:

“Manage albums “Copy “ Deiete “Move NawPix on your computer. Image Search | Search and dounioad NawPix from a website. Note: This feature is powered by Flickr Voice Transfers _ | Application that allows you t instal or remove voice fl from your Mio Activation Application used to activate a product key when you purchase a subscription or maps.

Mio Moov 500-Series |_What is MioMore Desktop? How do ! keep MioMore Desktop up-to-date? We recommend that you regulariy use MioMore Desktop to check the Mio server for MioMore Desktop software updates. How do ! update MioMore Desktop? Start AII Programs ® Mio ® MioMore Desktop ® Tools > Options =? General Select Auto check for updates checkbox. When you select this option, every time you access MioMore Desktop, the latest service packs and bug fixes if available are downloaded from the Mio server and applied to your Mio. Note: Updating software is different from upgrading software. To upgrade MioMore Desktop, you must first purchase à new version of MioMore Deskiop from a retailer, then install ion your Mio. MioMore Desktop Preferences Tools => Options => General Complete one of the following: H you want to … Then … upgrade from a previous version of MioMore Desktop follow the instructions in the Installation Guide or Upgrade Guide that came with your MioMre Desklop upgrade change the MioMore Desktop measurement lo metric units = Selectie Use metric units check box. change the MioMore Desktop measurement Lo decimals = Selectihe Decimal degrees check box.

Mio Moov 500-Series |_What is MioMore Desktop? My Maps The My Map application allows you to install new maps, remove maps from your device and purchase new maps. Start > AI Programs ® Mio =® MioMore Desktop =? My Maps Element Description CRE Cick to zoom in. B cv À drop dou list of continents inat have maps available for your Mo. Map Source A list of maps on Ihe DVD or available for purchase via the Mio store website. An br A list of maps installed on your Mio. Zoom Out Cick to zoom out. G Find City Click to open the Find City window to search for a city or town. G] Globe À map of the world or a continent selected indicating the maps: + onthe current DVD, + installed on your Mio or memory card, or + available from Mio.

Mio Moov 500-Series |_What is MioMore Desktop? How do I install maps onto my Mio? Your Mio comes with one or more pre-activated maps. You can install maps from the enclosed DVDs to a memory card or your Mio internal memory; however you may need to purchase a Map Product Key to activate the maps. Which map should 1 install? If you are not sure which map contains the town or city that you want to install, you can use the Find City window to identify the correct map. For more information, see "How do 1 know which map contains a particular city or town?" on page 86. How do I install maps from DVD?

1. Open MioMore Desktop, ifit is not already open:

The My Maps application will display.

3. Insert a Map DVD into your computer DVD drive

= The maps that are already installed on your Mio are green. = The maps that are unlocked and ready to be installed to your Mio are ye1ow. = The maps that require activation before being installed to your Mio are red. = The maps that are available for purchase from Mio are blue. Your computer opens Windows Explorer when the DVD is inserted, close the Windows Explorer window: 4... Complete the following: Ithe map to be installed is Then … yellow go to step. red the map needs to be activated via the Intemet before it can be installed; continue to steps.

5. If you connect to the Internet via a dial-up connection, connect to the Internet now.

Moov 500-Series |_What is MioMore Desktop?

7... Click the map you want to install to your Mio. Follow the prompts to activate your Map Product Key, including Enter the Map Product Key when prompted Your computer will connect to the Internet and activate your Map Product Key. When activation has completed, the map will change color to amber; continue to step 7. The map will change color to 21ow to indicate it has been selected. = To deselect a map, clickthe map again. Note: You may need lo install multiple maps Lo cover the required geographical area.

8. Complete the following:

Select the destination media for the selected maps, then click Transfer Now. The selected maps wil be installed and change color to green.

10. To use your Mio, disconnect the USB cable.

WARNING Do not disconnect the USB cable from the Mio USB Socket uni the installed map or maps have changed color to green.

Mio Moov 500-Series |_What is MioMore Desktop? How do | remove maps from my Mio?

Click My Maps. The My Maps application will display. From the My Mio panel, select the check box next to the map you want to remove. Click Remove Maps to remove the selected maps. Confirm that you want to remove the selected map when prompted The map is removed from your Mio. How do 1! know which map contains a particular city or town? Use the Find City window to find the map that contains a particular city or town.

The My Maps application will display.

2. Onthe My Maps panel, click Find City.

The Search for City window will open.

3. Type the name of the city or town in the City Name field.

The list of available cities will reduce to match your search

4. Select the name of the city or town, then click Show on Map

The globe will rotate to centre on the selected city or town. My Map Preferences Tools > Options => My Maps H you want to … Then … show longitude and latitude lines select the Show Graticule check box. The longitude and latitude lines wil display.

Note: To view the latitude and longiude, you need lo have a region selected.

Moov 500-Series |_What is MioMore Desktop? What is a Major Road Network map? Continuous continental navigation Navigation between particular countries is not available on all models. Major Road Network maps allow you to seamlessiy navigate between installed maps without installing maps of all regions along your route. Each Major Road Network map covers a large area, such as North Amaerica, and contains main roads that connect cities and towns. You can select a road or Point of Interest on the Major Road Network map as your departure point or destination. All Major Road Network maps: “contain roads and ferry connections of high national and international importance. = use less memory than would be necessary Lo install all equivalent detailed maps. = exclude smaller roads and have a reduced level of geographical detail. How do I install or reinstall a Major Road Network map? Major Road Network maps can be installed to a new memory card or reinstalled to your Mio the same way detailed maps are installed. For more information, see “How do | install maps from DVD?" on page 84.

Mio Moov 500-Series |_What is MioMore Desktop? Photo Album Depending on your Mio model, certain Photo Album features may not be available Photo Album is a MioMore Desktop application which allows you to copy, delete or move pictures or albums on your computer. Start > AII Programs =? Mio => MioMore Desktop =? Photo Album D—_——_—

| KA D #HESFTELE Element Description D cr Gives access to Photo Album functional. CES Displays à list of al albums store in the NawPix library on your computer. Click an album to display its contents in the Album display area Click the View all pictures button to display all pictures stored in the NawPix library on your computer. My Mio albums Displays a list of albums tord on the Mo intemal memory and on the memory card if one is El inseted Click an album to display its contents in the Album display area Note: Only available on some models. Album display area Displays thumbnails of pictures in the selected album. Selected picture When a thumbnail is selected it displays with a blue border. Toolbar When a picture is selected, the icons wihich can be used will be active.

Search Type lo search for a NawPix by name.

Moov 500-Series |_What is MioMore Desktop? Toolbar

The following options are available on the toolbar: Button Description Create new album Click to create a new album in the NawPix library you are viewing. Rotate left Rotates he selected NavPix 90° to the left. Rotate right Rotates the selected NavPix 90° to the right. Transfer to your Mio or Transfer to your computer + Ifyou are viewing NauPix in the NauPix library on your computer, this will display as ‘Transfer to your Mio Click to transfer the selected NawPix to your Mio. + Iyou are viewing NawPix in the Mio library this wil display as Transfer to your computer. Click to transfer the selected NawPix to the NawPix library on your computer. Note: Only available on some models: Import NavPix Imports NavPix from your computer lo the NawPix library on your computer. View details Click to view the selected NavPix and edit NavPix details, including - NavPixname "latitude "longitude "description Export to Click to save NawPix lo your computer or à nelwork drive. Delete NavPix Click to delete the selected NawPix.

Mio Moov 500-Se: s | What is MioMore Desktop? How do | use Photo Album? How can ! view and edit pictures or albums on my computer? H you want to Then … Fotate à picture 10 left + selectihe picture from ie AIDUm display are. *___ cick Rotate left on ihe toolbar. Fotate a picture Lo right + selectihe picture from ie AIDum display area. + cick Rotate Righton {he toolbar. view the piclure details + seiectihe piure from ne AIDUm display are. *__ right click and select View Details or click View Details on the toolbar. edit GPS information + selectihe picture from ie AIDum display area. “click on the picture or click View Details on the toolbar. = Following information will display Name Latitude and Longitude Description “Edit ie details you want to modify. “Click OK to save the changes. delete a picture = selectihe picire from lhe Album display area. *__ right click and select Delete or click Delete NawPix on the toolbar.

Mio Moov 500-Series |_What is MioMore Desktop? What else can 1 do with pictures and albums on my computer? From the NawPix library on your computer, you can: “add a picture to another album “remove pictures from an album “view and edit details of a selected picture “upload pictures to Flickr" “export to disk “export pictures to Google Earth" “search for pictures “ viewall pictures in the library H you want to Then add a picture to another album |" in he Desktop albums section, select ihe album containing ihe NavPix you want lo include in another album

• selectthe NawPix then drag it lo the other album. Note: The selected NauPix is included in the new album, but is not moved, i.e., one instance of the NavPix in the library may be included in multiple albums. remove a piclure from an album |" in lne Desktop albums section, selectihe album containing ihe NavPix you Want lo remove + select the NawPix, right click and select Remove from album Note: Click ihe Delete icon on the toolbar if you want Lo delete the NawPix from all albums. view and edi picture details + select the piclure then click the View Details icon on {he Loolbar.
• _editthe fields as required upload picture to the Flickr website |" inthe Desktop albums section, selectthe album containing lhe NavPix you want to upload to the Flickr website. + select the NawPix, right click and then select Upload to Flickr. Note: You need a Flickr account to upload NawPix. To create a Flickr account visit ww ickr.com save a picture lo yourcomputer | Selectihe piclure from the Album display area + right click and select Export to disk or click Exportto disk on the toolbar. + Navigate lo an album on your computer were you want to save the Navi export to Google Earth" + inthe Desktop albums section, select {he album containing ihe piclure you want to export (only NavPix with GPS to Google Earth. coordinates can be exported to | selectihe NawPix, right click and then select Export to Google Earth Google Earth) + Navigate to a folder on your computer to save the file and then open in Google earth. Note: You need to install the Google Earth sofwære on your computer lo be able Lo viewr the file you have created. You can dounioad Google Earth from earth.google.com search for other NavPix You can search for other NawPix near the longitude and latitude of your NavPix using Flickr view all pictures in the library click the View all pictures button at the bottom of the Desktop album section

Mio Moov 500-Series |_What is MioMore Desktop? Photo Album Preferences Tools > Options => Photo Album Complete one of the following H you wantto … Then … change your NawPix location on your computer “ cick Change The Save ÀS dialog box will open. + select a location for your NawPix library “click Save. The waming message wil display and you will be prompled Lo confirm your action Your NawPix library is moved lo the new location. receive a warning message before deleting an image from your device select Warn me when permanentiy deleting an image from my device checkbox. receive a warning message before deleting an image from your NavPix library select Warn me when permanentiy deleting an image from my library checkbox.

Moov 500-Series |_What is MioMore Desktop? Image Search Depending on your Mio model, certain MioMore Desktop features may not be availabl Image Search is a MioMore Desktop application powered by Flickr" allowing you to download photos and import them to Photo Album. Start AII Programs =? Mio =? MioMore Desktop ® Image Search How do 1 download NauPix from the internet?

1. _Inthe Description field enter a search description for the image you are looking for.

2. Select one ofthe Sort by options.

Thumbnails of the NawPix wil display in the NawPix display area. Note: Vou can narrow your search by selecling the Advance Search check box and then selecting a cit from the drop down list or by entering longitude and latitude details. How do 1 import NawPix to Photo Album?

1. Fromthe NawPix display area select a picture or group of pictures you want to upload to your Photo Album.

2. Right click and select Import to Photo Album.

A new album is created in the Desktop album section of Photo Album. Note: For more information, see "How do | use Pholo Album?" on page 90.

Mio Moov 500-Series |_What is MioMore Desktop? My subscriptions Safety camera information is only available for selected countries. Your Mio contains pre-loaded safety camera information. To subscribe to current Mio safety camera information, use the enclosed DVD to install MioMore Desktop software on your computer. For the latest safety camera coverage, to subscribe to safety camera information and to see our latest offers, visit www. mio.com Each country has a colored circle indicating the status of your subscription. How do install Safety Camera information? Complete the following steps to install safety camera information on your Mio.

1. Purchase a subscription

2. Activate your subscription.

How do 1! know which Safety Camera information is available? Start AII Programs ® Mio => MioMore Desktop =? My Subscriptions

1. From the Available Subscription section, select the country for which you want to purchase the subscription.

2. Left click and select Activate my subscription.

The Activation window will display. ubscriptions are available only for those countries for which you have purchased maps.

3. Enter a product key and follow the prompt to activate your subscription.

Purchase a Subscription

1. To purchase a subscription Lo safety camera information, on the Subscriptions menu, select the country for

which you want to purchase the safety camera and then select Purchase an activation key from the Mio store. The Mio Store website will open. 2... Follow the prompts to purchase your subscription A product key will be sent to you via email when you have subscribed. You will need to use this product key to activate your subscription.

Moov 500-Series |_What is MioMore Desktop? Activate your Subscription Start > AII Programs ® Mio > MioMore Desktop

1. From Available Subscriptions section, select the country for which you want lo activate the safety camera

2. Right click and select Activate my subscription.

The Activation window will display.

3. Enterthe subscription product key in the Product Key field

Follow the prompts to update your subscription. Your software will update automatically. How do ! update Safety Camera information on my Mio? Start > AII Programs ® Mio =® MioMore Desktop =? My Subscription My Mio section wil display a list of subscriptions already installed on your device. Icon Description red Expired subscriptions. "right click lo purchase a new subscription. Yellow Available subscrptions. “right click lo update and purchase new subscription. green Active subscriptions. Note: No updates are available for these subscriptions.

Mio Moov 500-Series |_What is MioMore Desktop?

The Voice Transfer application is part of MioMore Desktop and allows you to install or remove voice files. e Transfer Voice files take up space on your Mio's internal memory. If you do not use a voice file, you can remove it to free up space. You can later reinstall it to your Mio if required Start AII Programs ® Mio => MioMore Desktop ® Voice Transfer How do I install a voice file? In the Available voice files section, select the voice file you would like to install, then click Install selected voices How: do I remove a voice file? In the Available voice files section, select the voice file you would like to remove, then click Remove selected voices.

Mio Moov 500-Series |_What is MioMore Desktop? How do ! backup my Mio? You can save backups of the following information, and later restore them to your Mio: = Favorites and My Home = Preferences, including Point of Interest and NavPix preferences “ Multi-stop trips “Recent locations. How do 1 Backup my Mio?

1. Tools ® Backup and Restore

The Backup & Restore window will open.

2. Click Create new backup.

The Create new backup window will display.

3. Select the data you would like to backup, then enter a description for the backup in the Description field.

The New Backup window will close and your backup will be saved to your computer. The backup will be listed on the Backup & Restore window. How do 1 Restore a Backup to my Mio?

1. Tools ® Backup Restore

The Backup & Restore window will open.

2. Selectthe backup from the list, then click Restore, then click OK.

The backup will be restored to your Mio. How do 1 Delete a Backup?

1. Tools > Backup Restore

The Backup & Restore window will open.

2. Select from the list the backup to delete.

3. Click Delete, then click OK.

The backup is deleted.

Mio Moov 500-Se: s | Reference Reference Point of Interest categories Description Description Aitine Access G:] Airport Amusement Park Arts or Cultural Centre Bank ERES Boat Ramp Breakdown Service, Car Repair Faciity Building ARRET Car Dealer EX [ecran pan, Traiter pa Cash Dispenser FR lose Centre of Settlement + Church Cinema City Centre College or University Company Concert Hall, Music Centre, Opera Convention Centre, Exhibition Centre

Courhouse Cultural Centre Dentist Pet |Doctor Drive-Through Botlle Shop Embassy Emergency Medical Service Ferry Terminal Fire Station Frontier Crossing General POI Goff course Government Office Hospital/Polyalinie Hotel or Motel 92 0 4 9418518 905 0142 N 0 Ice Skating Rink na Important Tourist Attraction Leisure Centre, Sports Centre Library Military Cemetery Monument Mountain Pass #10 )9)|E4 03) ER NE Mountain Peak Museum Nightlife Open Parking Area Park and Recreation Area Gas station Pharmacy le. )bs|[< ITR es 421© Place of Worship

Mio Moov 500-Series |_Reference Icon Description Description Police Station Post Office

Railway Station Rent-a car Parking JE BE Rest Area Restaurant Area Scenic or Panoramic View 3 |scroo Shop Shopping Centre Stadium Swimming Pool Tennis Court Theatre Tourist Information Office Travel Agency SRPSADEE 91919) 4/0 E Vehicle Equipment Provider Veterinarian Water Sports Winery Yacht Basin Zoological park (200) Branded Points of Interest Branded Points of Interest are available on some maps. These include well-known restaurants, accommodation providers, tourist attractions, gas stations, etc. The icon will usually display the company logo. Point of Interest categories by Mio Icon Description Favorite destination Muliple route tip My home NavPix f Interest categories by subsc ption Description Safety Cameras Safety Camera (mobile) Safety Camera (average) Red Light Camera

Mio Moov 500-Se: Reference s | Traffic and other TMC Events Each TMC Event is sorted in to one of nine categories. When an Event is received, one of the following icons will display Event |AvoidedEvent | Message Type Event Description Danger There is a dangerous siuation on he route: for example, people are on the road A Traffic ‘Any event that will cause a delay on a route. Weather Weather condilons are adversely affecting a route: for example, there is ice on 1he road. Wamings There is a situation of which you should be aware on Ine route, but iLis not serious enough to be considered a dangerous situation: for example, a minor accident has taken place. à EN Forecast An eventis expecled lo oceur on a route. Restrictions There is a restricted flow of traffic on a route; for example, a lane has been closed on a freeway. © © Clearance A Traffic Event that has now been cleared. À à Information ‘All other events.

4) À Roadworks Roadworks are taking place on a route.

If a Traffic or Clearance event has a recommended detour, the following icons will display Event |AvoidedEvent | Message Type Event Description Æ & Traffic Detour A Traffic Event, for which a detour is recommended. @ (4 Clearance Re-route A Clearance Event, for which a re-route is recommended. Note: Avoided Event icons will only display on the 2D Map and 3D Map, at the Event location.

Mio Moov 500-Series |_Reference Safety Camera POIs Mio products are designed lo be used as an aid Lo safer driving. You can receive messages Lo alert you lo locations of safety cameras, which wil enable you lo monitor your speed through these areas. Mio does not warrant that all types and locations of safety camera data are available, as cameras may be removed, relocated or new cameras installed. Mio does not condone speeding or any other failure to comply with your local traffic laws. It is your responsibility to drive within the posted speed limit at all times and to drive in a careful manner. Mio accepts NO liablity whatsoever for you receWing any speeding fines or points on your license through using this device. Mio does not guarantee the accuracy of the data contained wilhin this database either expressed or implied. In the event you receive à fine or any other penalty for speeding or contravention of any traffic law, or are involved in an accident, Mio is not responsible for any damages of any type. In some countries the data information regarding safety or speed cameras may conflict with local law andor regulations. I is your responsibility to make sure {hat your use of he dat is in compliance with local laws andlor regulations. Usage is at your own risk Disclaimer Due to continued product development this information may change without notice. Mio does not warrant that this document is error-free. ‘The screenshots and other presentations shown in this manual may differ from the actual screens and presentations generated by the actual product. All such differences are minor and the actual product will deliver the described functionality as presented in this User Manual in all material respects. Compliance WARNING This product, is packaging and Îfs components contain chemicals known to Ihe State of Callfomia lo cause cancer, birih defects or reproductive harm. This Notice is being provided in accordance with California's Proposition 65. Note: For regulatory identification purposes, Mio Moov 500-Series is assigned a model number of N210.

Mio Moov 500-Series |_Reference Copyright © 2008 MAC Intenational Corporation. Mio is either a registered trademark or trademark of MITAC Intermatonal Corporation and is used under icense by Mio Technology Limied. Al High reserved ‘The software contains proprietary information of MITAC International Corporation; i is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electroni mechanical, phoocopying, recording or otherwise, without the prior writlen permission of Mio. Back-On-Track, Drive-Away, MioMore Desktop, Mio Connect, NawPix, MioMap and Tum-by-Tum are either registered trademarks or trademarks of MITAC Intemational Corporation and are used under license by Mio Technology Limited. AI rights reserved. Microsoft, Windows, Windows Vista, and Intemet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. AI rights reserved. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Mio Technology Limited is under license. Location Identiers © 2005 Intemational Air Transport Association POI Data © 2007 InfoUSA. Al other trademarks and registrations are the property of their respective owners. Published in New Zealand

Mio Moov 500-Series |_For more Information For more information Online support For 24/7 help and support with Mio products, visit our Technical Support website at: www.mio.com Mio Club You can register your Mio with the Mio Club - a section of our website dedicated exclusively to owners of Mio navigation products: www.mio.com As a registered Mio Club member, you'll have access to the safety camera database, software updates, a regular newsletter, tips, FAQs and much more! Phone support (866) 646 4477 (Mio-4GPS)