MPR-47S-OG-D-0 5 - Analyseur réseau ENTES - Free user manual and instructions
Find the device manual for free MPR-47S-OG-D-0 5 ENTES in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of product | Motor Protection Relay |
| Model | MPR-47S-OG-D-0 5 |
| Brand | ENTES |
| Dimensions (H x W x D) | 90 x 45 x 100 mm |
| Weight | 0.2 kg |
| Power supply voltage | 230 V AC, 50/60 Hz |
| Operating temperature | -20°C to +60°C |
| Rated current range | 0.1 – 10 A |
| Number of phases | 3 |
| Main functions | Overload, phase failure, phase sequence, undercurrent, overcurrent |
| Reset mode | Automatic or manual (selectable) |
| Output relay | 1 changeover (SPDT), 5 A / 250 V AC |
| Indicators | LED for supply, trip, and alarm |
| Mounting | DIN rail (EN 60715) |
| Degree of protection | IP20 (enclosure), IP40 (front panel) |
| Safety standards | IEC/EN 60255, IEC/EN 60947 |
| Maintenance | No routine maintenance required; periodic check of wiring and settings |
| Cleaning | Wipe with a dry cloth; do not use solvents |
| Spare parts and repairability | Replace entire unit if defective; no user-serviceable parts inside |
| Warranty | 2 years (manufacturer) |
Frequently Asked Questions - MPR-47S-OG-D-0 5 ENTES
How do I wire the MPR-47S-OG-D-0 5 relay?
Follow the wiring diagram in the manual. Connect the three-phase supply to terminals L1, L2, L3 and the motor to T1, T2, T3. The control supply (230 V AC) goes to A1 and A2. The output relay is on terminals 11, 12, 14.
What is the rated current range?
The rated current range is 0.1 to 10 A. Set the dial to match your motor's full-load current.
How do I reset the relay after a trip?
You can select automatic or manual reset via a DIP switch. For manual reset, press the reset button on the front panel after the fault is cleared.
Can I use this relay for single-phase motors?
No, the MPR-47S-OG-D-0 5 is designed for three-phase motors only.
What does the LED indication mean?
The green LED indicates supply present, yellow LED indicates relay energised (motor running), and red LED indicates a trip condition.
How do I set the trip class?
The trip class is set via DIP switches. Refer to the manual for the correct setting according to your motor's starting characteristics (Class 10, 20, or 30).
Is the relay suitable for outdoor installation?
No, the relay has an IP20 rating; it should be installed indoors in a clean, dry location. Use an enclosure for harsh environments.
What happens if a phase is lost?
The relay will trip within 2 seconds to protect the motor from single-phasing. The red LED will flash.
Can I test the relay operation?
Yes, press the TEST button to simulate a trip. The relay should de-energise and the red LED turn on. Press RESET to restore.
Where can I download the manual?
The manual is available for free on notice-facile.com. Search for 'MPR-47S-OG-D-0 5 ENTES'.
User questions about MPR-47S-OG-D-0 5 ENTES
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Analyseur réseau in PDF format for free! Find your manual MPR-47S-OG-D-0 5 - ENTES and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MPR-47S-OG-D-0 5 by ENTES.
USER MANUAL MPR-47S-OG-D-0 5 ENTES
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ENTES
Model : MPR-47S-OG-D-0 5
Category : Analyseur réseau