L-590AXII - Receiver LUXMAN - Free user manual and instructions
Find the device manual for free L-590AXII LUXMAN in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Integrated Amplifier (Receiver) |
| Dimensions (W x H x D) | 440 x 178 x 422 mm |
| Weight | 22.8 kg |
| Power Consumption | 220 W (idle), 420 W (rated output) |
| Power Output | 30 W + 30 W (8 Ω, Class A) |
| Frequency Response | 20 Hz – 20 kHz (±0.2 dB) |
| Total Harmonic Distortion | 0.005% (1 kHz, 8 Ω, 1 W) |
| Signal-to-Noise Ratio | 110 dB (line input) |
| Input Sensitivity/Impedance | Line: 150 mV / 47 kΩ; Phono (MM): 2.5 mV / 47 kΩ; Phono (MC): 0.3 mV / 100 Ω |
| Inputs | 4 x Line (RCA), 1 x Phono (MM/MC), 1 x Balance (XLR) |
| Outputs | Speaker A/B terminals, Pre-out, Rec out, Headphone (6.3 mm) |
| Speaker Impedance | 4 – 16 Ω |
| Remote Control | Yes (RC-200) |
| Power Supply Voltage | 230 V AC, 50/60 Hz (some models 120 V) |
| Safety Precautions | Operate on specified voltage; avoid moisture; ensure ventilation |
| Maintenance | Wipe with soft dry cloth; periodic inspection by qualified technician |
| Repairability / Spare Parts | Contact Luxman authorized service center for genuine parts |
| General Information | Class A operation; high-quality aluminum chassis; handmade in Japan |
Frequently Asked Questions - L-590AXII LUXMAN
How do I connect speakers to the L-590AXII?
Use high-quality speaker cables. Connect to the Speaker A or B terminals, ensuring proper polarity (red to +, black to -). Impedance must be between 4 and 16 ohms.
What turntable cartridges does the phono stage support?
The built-in phono stage supports both MM (moving magnet) and MC (moving coil) cartridges. Select the appropriate gain via the rear switch.
Can I use the L-590AXII with low-impedance speakers?
Yes, the amplifier is stable with 4 ohm speakers. For impedances below 4 ohms, consult the manual to avoid overheating.
How do I clean and maintain the amplifier?
Use a soft, dry cloth to wipe the exterior. Do not use chemical solvents. For internal cleaning, contact a qualified technician.
What is the recommended warm-up time for optimal Class A operation?
Allow approximately 30 minutes for the amplifier to reach stable operating temperature for best sound quality.
Does the remote control require batteries?
Yes, the supplied RC-200 remote uses two AAA batteries. Replace when range becomes reduced.
What should I do if the amplifier overheats?
Ensure adequate ventilation around the unit. Do not stack other components on top. If overheating persists, reduce volume and allow cooling.
Can I use the L-590AXII as a preamp only?
Yes, use the Pre-out jacks to connect to an external power amplifier. The internal amplifier stage can be disconnected via the rear switch.
How do I troubleshoot no sound?
Check speaker connections, input selection, mute switch, and volume level. Ensure the amplifier is not in protection mode (red LED).
What is the warranty period for Luxman products?
Luxman offers a 2-year limited warranty for most regions. Register your product online to activate coverage.
User questions about L-590AXII LUXMAN
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual L-590AXII - LUXMAN and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. L-590AXII by LUXMAN.
USER MANUAL L-590AXII LUXMAN
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : LUXMAN
Model : L-590AXII
Category : Receiver