1229 Q - Turntable DUAL - Free user manual and instructions
Find the device manual for free 1229 Q DUAL in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Quartz-Locked Direct Drive Turntable |
| Brand | Dual |
| Model | 1229 Q |
| Dimensions (W x D x H) | 420 mm x 360 mm x 150 mm |
| Weight | 10 kg |
| Power Supply | 120 V / 240 V AC, 50/60 Hz |
| Drive System | Direct drive with quartz speed control |
| Speeds | 33 1/3 and 45 rpm |
| Tonearm Type | Static balanced S-shaped tonearm |
| Anti-skating | Adjustable anti-skating control |
| Tracking Force Range | 0.5 to 4 grams |
| Cartridge Included | Dual DN 155 E (or equivalent) |
| Output | Phono (RCA) with ground wire |
| Auto Shut-off | Automatic shut-off at end of record |
| Platter Material | Heavy non-resonant die-cast aluminum |
| Maintenance | Clean stylus regularly; replace belt if needed |
| Safety | Auto shut-off prevents unnecessary wear |
| Spare Parts Availability | Stylus, belt, and drive components available online |
| General Information | High-quality turntable from the 1970s, renowned for precision and durability |
Frequently Asked Questions - 1229 Q DUAL
How do I set up the Dual 1229 Q turntable?
Place the turntable on a level, stable surface. Connect the RCA cables to your amplifier's phono input and the ground wire to the grounding terminal. Set the tracking force according to the cartridge specifications (typically 2-3 grams). Adjust anti-skating to match.
What speeds does the Dual 1229 Q support?
It supports 33 1/3 and 45 rpm. Use the speed selector switch to choose the desired speed. The quartz lock ensures accurate pitch.
How can I replace the stylus on my Dual 1229 Q?
First, remove the headshell by pulling it straight out. Then, gently pull the old stylus forward from the cartridge. Insert the new stylus by pushing it back until it clicks. Reattach the headshell.
Why is my turntable not spinning at the correct speed?
Check if the quartz lock is engaged (if available). Clean the speed selector switch. If the belt is worn (in belt-drive models), replace it. For direct drive, the motor may need servicing.
How do I clean the stylus?
Use a stylus cleaning brush or a soft brush dipped in isopropyl alcohol. Gently brush from back to front. Do not use excessive force to avoid damaging the cantilever.
What is the correct tracking force for my Dual 1229 Q?
The recommended tracking force depends on the cartridge. For the original Dual DN 155 E, it is about 2.5 grams. Always refer to the cartridge manual and use a stylus force gauge.
How do I adjust the anti-skating?
Set the anti-skating dial to the same value as the tracking force. For example, if tracking force is 2.5 grams, set anti-skating to 2.5. Fine-tune by listening for distortion.
Can I use a moving coil cartridge with this turntable?
Yes, but you will need a step-up transformer or a phono preamp with MC input. The tonearm is suitable for low-compliance cartridges.
How do I replace the drive belt (if applicable)?
Remove the platter by lifting it straight up. Take off the old belt from the motor pulley and platter rim. Put the new belt around the platter rim first, then stretch it over the motor pulley. Reinstall the platter.
What should I do if the turntable makes a humming noise?
Ensure the ground wire is properly connected to the amplifier. Check that the RCA cables are not near power cords. If the hum persists, the cartridge may need replacement or the unit may need servicing.
User questions about 1229 Q DUAL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Turntable in PDF format for free! Find your manual 1229 Q - DUAL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 1229 Q by DUAL.