PS2100 - Receiver MARANTZ - Free user manual and instructions
Find the device manual for free PS2100 MARANTZ in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Brand | Marantz |
| Model | PS2100 |
| Power Output | 45 watts per channel into 8 ohms |
| Total Harmonic Distortion | 0.02% at rated power |
| Frequency Response | 20 Hz - 20 kHz ±0.5 dB |
| Input Sensitivity (Phono) | 2.5 mV |
| Input Sensitivity (Line) | 200 mV |
| Signal-to-Noise Ratio | 80 dB (line) |
| Tuner Bands | FM, AM |
| Dimensions (W x H x D) | 17.3 x 5.5 x 13.8 inches |
| Weight | 18.5 lbs (8.4 kg) |
| Power Consumption | 180W (max) |
| Inputs | Phono, Aux, Tape, Tuner |
| Outputs | Speaker A/B, Headphone, Tape Rec |
| Speaker Impedance | 4-16 ohms |
| Cleaning | Wipe with dry soft cloth; avoid solvents |
| Safety | Do not expose to moisture; ensure ventilation |
| Repairability | Service by qualified technician; use original parts |
| General Information | Vintage Marantz receiver; manual available online |
Frequently Asked Questions - PS2100 MARANTZ
How do I connect speakers to the Marantz PS2100?
Use the speaker terminals on the rear panel. Connect the positive (+) terminal to the red binding post and negative (-) to the black. Ensure impedance is between 4 and 16 ohms. You can select speakers A, B, or both using the front panel switch.
What is the power output of the PS2100?
The Marantz PS2100 delivers 45 watts per channel into 8 ohms with low distortion (0.02% THD). It can drive most bookshelf and floorstanding speakers efficiently.
How do I clean the receiver?
Unplug the unit. Use a soft, dry cloth to wipe the exterior. Do not use any liquids or abrasive cleaners. For the front panel, a slightly damp cloth can be used, but avoid getting moisture inside.
Why is there no sound from one channel?
Check speaker connections and the balance control (set to center). Verify the source is sending stereo signal. Try swapping speakers to isolate the issue. If persistent, the amplifier may require service.
Can I connect a turntable directly?
Yes, the PS2100 has a dedicated phono input with built-in preamp for moving magnet (MM) cartridges. Connect your turntable's RCA cables to the Phono inputs and ground wire to the GND terminal.
How do I set the FM antenna?
Connect the supplied dipole antenna or an outdoor FM antenna to the FM antenna terminals. Extend the dipole for best reception. For AM, use the loop antenna provided and rotate for minimal interference.
What is the recommended speaker impedance?
The PS2100 is designed for speakers with impedance between 4 and 16 ohms. Using speakers below 4 ohms may cause overheating. For safe operation, use 8 ohm speakers for best performance.
How do I reset the receiver?
There is no factory reset function. To clear settings, unplug the unit for 30 minutes. Manually set tone controls, balance, and volume to desired levels.
Where can I find the user manual?
The manual is available for free download on notice-facile.com. Visit https://notice-facile.com/marantz/ps2100 and select your language to download a PDF version.
How do I maintain the receiver for long life?
Keep the receiver in a well-ventilated area away from direct sunlight and moisture. Dust the vents regularly. Use a surge protector. If the unit runs hot, ensure at least 10 cm clearance above and on sides.
User questions about PS2100 MARANTZ
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual PS2100 - MARANTZ and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PS2100 by MARANTZ.
USER MANUAL PS2100 MARANTZ
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : MARANTZ
Model : PS2100
Category : Receiver