SR2100 - Receiver MARANTZ - Free user manual and instructions
Find the device manual for free SR2100 MARANTZ in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Brand | Marantz |
| Model | SR2100 |
| Power Output | 30 watts per channel into 8 ohms |
| Total Harmonic Distortion | 0.5% at rated power |
| Frequency Response | 20 Hz - 20 kHz |
| Signal-to-Noise Ratio | 75 dB (MM phono) |
| Input Sensitivity | 2.5 mV (MM phono), 150 mV (line) |
| FM Tuner Sensitivity | 2.5 μV (mono) |
| Dimensions (W x H x D) | 17.3 x 5.5 x 13.8 inches (440 x 140 x 350 mm) |
| Weight | 18.0 lbs (8.2 kg) |
| Power Consumption | 300 watts (max) |
| Power Supply | 120 V, 60 Hz (US model) |
| Inputs | Phono (MM), Aux, Tuner, Tape, Tape Monitor |
| Outputs | Speaker A/B, Headphone (1/4 inch) |
| Controls | Volume, Bass, Treble, Balance, Loudness, Selector |
| Tuning Range | FM: 88-108 MHz; AM: 530-1710 kHz |
| Cleaning | Wipe with soft, dry cloth; do not use solvents |
| Safety Precautions | Avoid moisture; unplug during lightning storms; use in well-ventilated area |
| Spare Parts and Repairs | Contact authorized Marantz service center for parts and service |
Frequently Asked Questions - SR2100 MARANTZ
How do I connect my turntable to the SR2100?
Connect the turntable's RCA cables to the Phono input. Ensure the turntable has a moving magnet (MM) cartridge and the ground wire is attached to the GND terminal.
What is the power output of the Marantz SR2100?
The SR2100 delivers 30 watts per channel into 8 ohms, with a total harmonic distortion of 0.5% at rated power.
Can I use speakers with 4 ohm impedance?
The SR2100 is designed for 8 ohm speakers. Using 4 ohm speakers may cause overheating or damage. It is recommended to use 8 ohm speakers.
How do I clean the receiver?
Unplug the unit and wipe the exterior with a soft, dry cloth. Do not use any solvents, abrasive cleaners, or compressed air inside the vents.
Why is there no sound from one channel?
Check the balance control, speaker connections, and the source input. Also test with headphones to isolate the issue. If the problem persists, the amplifier may need service.
How do I set the FM antenna?
Connect the supplied FM dipole antenna to the FM ANT terminals. Extend it for best reception. For AM, connect a loop antenna to the AM ANT terminals.
What is the purpose of the Tape Monitor loop?
The Tape Monitor allows you to connect a tape deck or processor. When engaged, it routes the signal through the external device, enabling recording or processing.
Does the SR2100 have a subwoofer output?
No, the SR2100 does not have a dedicated subwoofer output. You can connect powered subwoofers via speaker-level inputs or use a speaker-level to line-level adapter.
What should I do if the receiver overheats?
Ensure proper ventilation: leave at least 4 inches (10 cm) of space above and around the unit. Reduce volume and avoid operating in direct sunlight or enclosed spaces.
How do I reset the SR2100?
Turn off the unit, unplug it from AC power, wait 30 seconds, then plug it back in. This will clear temporary issues but does not affect stored settings (since it is analog).
User questions about SR2100 MARANTZ
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual SR2100 - MARANTZ and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SR2100 by MARANTZ.
USER MANUAL SR2100 MARANTZ
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : MARANTZ
Model : SR2100
Category : Receiver