SEN-Pressure10 - Uncategorized Joy-It - Free user manual and instructions
Find the device manual for free SEN-Pressure10 Joy-It in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Pressure Sensor Module |
| Model | SEN-Pressure10 |
| Brand | Joy-It |
| Operating Voltage | 3.3V - 5V DC |
| Pressure Range | 0 - 10 bar (0 - 1 MPa) |
| Output Signal | Analog voltage (0-5V proportional to pressure) |
| Interface | Analog pin |
| Operating Temperature | -20°C to +85°C |
| Dimensions | 20 mm x 15 mm x 5 mm |
| Weight | 5 g |
| Accuracy | ±0.5% of full scale |
| Response Time | < 10 ms |
| Connection | 3-pin header (VCC, GND, OUT) |
| Compatibility | Arduino, Raspberry Pi, and other microcontrollers |
| Maintenance | Keep dry and clean; wipe with a soft cloth if needed |
| Safety Precautions | Do not exceed maximum pressure; avoid reverse polarity |
| Spare Parts / Repairability | No user-serviceable parts; replace module if faulty |
| General Information | Designed for liquid and gas pressure measurement |
Frequently Asked Questions - SEN-Pressure10 Joy-It
How do I wire the SEN-Pressure10 to an Arduino?
Connect the VCC pin to 5V (or 3.3V), GND to ground, and the OUT pin to an analog input (e.g., A0). Use the analogRead() function to read the voltage.
What is the pressure range of this sensor?
The sensor measures pressures from 0 to 10 bar (0 to 1 MPa), with a proportional analog output.
Can I use this sensor with a Raspberry Pi?
Yes, connect the OUT pin to an ADC (e.g., MCP3008) as the Raspberry Pi does not have analog inputs. Use the SPI interface to read the ADC value.
What is the output voltage at different pressures?
The output is linear: at 0 bar, output is 0V; at 10 bar, output is 5V (or 3.3V depending on supply). So pressure = (analog reading / 1023) * supply voltage * 2 (for 5V supply).
How accurate is the SEN-Pressure10?
The accuracy is ±0.5% of full scale, meaning ±0.05 bar at 10 bar.
Can I measure both liquids and gases?
Yes, this sensor is compatible with non-corrosive liquids and gases. Avoid using with corrosive or viscous fluids.
Do I need calibration?
The sensor is factory-calibrated, but you can perform a two-point calibration using known pressures for better accuracy.
What is the maximum voltage I can apply?
The recommended operating voltage is 3.3V to 5V DC. Do not exceed 5.5V to avoid damage.
How do I clean the sensor?
Use a soft, dry cloth to wipe the surface. Avoid using liquids or solvents. Keep the sensor dry.
What if the sensor is not reading correctly?
Check wiring and power supply. Ensure the pressure port is not blocked. If issues persist, the module may be defective; replace it.
User questions about SEN-Pressure10 Joy-It
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual SEN-Pressure10 - Joy-It and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SEN-Pressure10 by Joy-It.
USER MANUAL SEN-Pressure10 Joy-It
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Joy-It
Model : SEN-Pressure10
Category : Uncategorized