SBC-LCD128x64 - Uncategorized Joy-It - Free user manual and instructions
Find the device manual for free SBC-LCD128x64 Joy-It in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LCD Display Module |
| Model | SBC-LCD128x64 |
| Brand | Joy-It |
| Display Technology | Monochrome LCD |
| Resolution | 128 x 64 pixels |
| Backlight | LED Backlight (white or blue) |
| Interface | I2C / SPI (selectable via jumpers) |
| Operating Voltage | 3.3V or 5V compatible |
| Dimensions (PCB) | Approx. 60 x 30 mm |
| Mounting Holes | 4 x M3 holes (compatible with Raspberry Pi HAT) |
| Weight | Approx. 20 g |
| Key Features | Low power, wide viewing angle, pre-soldered header |
| Driver IC | SSD1306 or similar (monochrome OLED driver compatible) |
| Compatible Platforms | Raspberry Pi, Arduino, STM32, ESP32, etc. |
| Library Support | Adafruit SSD1306, luma.oled, etc. |
| Included Accessories | 4-pin or 7-pin header, possibly jumper wires |
| Care & Cleaning | Wipe gently with a dry microfiber cloth; avoid liquids |
| Safety | Handle with care; avoid static discharge; do not short circuits |
Frequently Asked Questions - SBC-LCD128x64 Joy-It
How do I connect the SBC-LCD128x64 to a Raspberry Pi?
Connect the display to the Raspberry Pi's GPIO header using I2C (pins 1, 3, 5, 7) or SPI (pins 19, 21, 23, 24). Refer to the manual for pinout details.
What driver does this LCD use?
The display typically uses the SSD1306 driver, which is widely supported by libraries like Adafruit_SSD1306 and luma.oled.
Can I use this display with an Arduino?
Yes, the display works with Arduino via I2C or SPI. Use the U8g2 or Adafruit SSD1306 library.
What voltage does the display require?
The module can operate at 3.3V or 5V, selectable by jumper. Most SBCs like Raspberry Pi use 3.3V logic.
How to change the I2C address?
The I2C address can be changed by soldering the address jumpers on the back of the board. Default is 0x3C, alternative is 0x3D.
Does the display have a backlight?
Yes, it has a white or blue LED backlight that can be controlled via PWM on a dedicated pin.
How to clean the LCD screen?
Gently wipe with a dry microfiber cloth. Do not use liquids or abrasive materials.
Is there a library for Python on Raspberry Pi?
Yes, use the Adafruit CircuitPython SSD1306 library or luma.oled for Python. Both support the SSD1306 driver.
What is the resolution of the display?
The display has a resolution of 128x64 pixels, monochrome.
Can I use this display with an ESP32?
Yes, ESP32 works well via I2C or SPI. Use the Adafruit SSD1306 or U8g2 library in Arduino IDE.
User questions about SBC-LCD128x64 Joy-It
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual SBC-LCD128x64 - Joy-It and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SBC-LCD128x64 by Joy-It.
USER MANUAL SBC-LCD128x64 Joy-It
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Joy-It
Model : SBC-LCD128x64
Category : Uncategorized