SuperServer 1028U-TNRTP+ - Server Supermicro - Free user manual and instructions
Find the device manual for free SuperServer 1028U-TNRTP+ Supermicro in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rack Server (1U) |
| Dimensions (H x W x D) | 1.7" x 17.2" x 25.6" (43 x 437 x 650 mm) |
| Weight | Approximately 30 lbs (13.6 kg) |
| Power Supply | Dual redundant 1600W (80+ Platinum) |
| Processor Support | Dual Intel Xeon Scalable (1st/2nd Gen) |
| Memory | Up to 1.5TB DDR4 ECC, 16 slots |
| Storage | 8x 2.5" hot-swap SAS3/SATA3 drive bays |
| Expansion Slots | 2x PCI-E 3.0 x16 (full-height, half-length) |
| Networking | Dual 10GbE RJ45, dedicated IPMI LAN |
| Management | IPMI 2.0 with KVM over IP |
| Operating Temperature | 10°C to 35°C (50°F to 95°F) |
| Safety Certifications | FCC, CE, UL, RoHS |
| Maintenance | Hot-swap fans, redundant PSUs, tool-less access |
| Spare Parts Availability | Wide range of spare parts from Supermicro |
| Repairability | Modular design; easy replacement of key components |
| General Information | SuperServer 1028U-TNRTP+; Intel C621 chipset |
Frequently Asked Questions - SuperServer 1028U-TNRTP+ Supermicro
How do I access the IPMI interface for the first time?
Connect to the dedicated IPMI LAN port, set your PC to the same subnet (default IP is 192.168.1.2), open a browser and enter the IP. Default credentials are ADMIN / ADMIN. Change them immediately for security.
What type of memory is supported?
The server supports DDR4 ECC Registered (RDIMM) or Load Reduced (LRDIMM) memory, up to 1.5TB total in 16 slots. Use modules rated for 2666/2400/2133 MHz.
Can I install a GPU card?
Yes, the server has two PCI-E 3.0 x16 slots. However, due to power and thermal constraints, only single-width GPUs up to 150W are recommended. The slots are full-height, half-length.
How to update BIOS or firmware?
Download the latest BIOS/IPMI firmware from the Supermicro support page. Use the SUMC (SuperUpdate Manager) tool or the IPMI web interface to apply updates. Always back up current settings first.
What is the default administrator password?
The default BIOS password is ADMIN (all caps). For IPMI, the default username and password are both ADMIN. It is strongly recommended to change these on initial setup.
How do I identify the components inside the chassis?
Refer to the Quick Reference Guide on the inside of the top cover. The manual provides detailed layouts of the motherboard, drive bays, and connectors.
What is the maximum power consumption?
With dual high-end processors and fully populated memory/storage, the system can draw up to 800-1000W under load. The redundant 1600W PSUs provide ample headroom.
Can I mix SAS and SATA drives in the same system?
Yes, the backplane supports both SAS3 and SATA3 drives. However, mixing drive types in a RAID array is not recommended. Use the same interface for optimal performance.
How to reset IPMI to factory defaults?
You can reset IPMI by powering off the server, pressing and holding the IPMI Reset button (if present) for 10 seconds, or via the IPMI web interface under Maintenance > Factory Defaults.
What RAID configurations are supported?
The server supports software RAID (Intel VROC) and optional hardware RAID controllers. Common levels: 0, 1, 5, 6, 10. For hardware RAID, install an add-in controller in a PCIe slot.
User questions about SuperServer 1028U-TNRTP+ Supermicro
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual SuperServer 1028U-TNRTP+ - Supermicro and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SuperServer 1028U-TNRTP+ by Supermicro.
USER MANUAL SuperServer 1028U-TNRTP+ Supermicro
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Supermicro
Model : SuperServer 1028U-TNRTP+
Category : Server