DBT-900AP - Access Point D-LINK - Free user manual and instructions
Find the device manual for free DBT-900AP D-LINK in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Bluetooth Access Point |
| Brand | D-Link |
| Model | DBT-900AP |
| Bluetooth Standard | Bluetooth 2.0+EDR |
| Maximum Range | Up to 100 meters in open field |
| Number of Supported Devices | Up to 7 devices simultaneously |
| Power Supply | 5 V DC via power adapter (included) |
| Dimensions (L x W x H) | 110 x 75 x 30 mm |
| Weight | 150 g |
| Interfaces | 1 Ethernet RJ-45 port, 1 power jack |
| Security | 128-bit encryption, PIN code authentication |
| LED Indicators | Power, Bluetooth link, activity |
| Operating Temperature | 0°C to 40°C |
| Operating Humidity | 10% to 90% non-condensing |
| Configuration | Via web interface or software utility |
| Maintenance and Cleaning | Clean with a soft, dry cloth. Do not use abrasive products. |
| Repairability | Spare parts not available. Contact customer service for repairs. |
| Package Contents | Bluetooth access point, power adapter, Ethernet cable, quick installation guide |
Frequently Asked Questions - DBT-900AP D-LINK
How to configure the D-Link DBT-900AP?
Connect the device to your network via the Ethernet port, then access the web interface via the default IP address (usually 192.168.0.50). Use the default username and password (admin/admin). Follow the setup wizard to configure the Bluetooth mode.
What is the range of the DBT-900AP?
The range is approximately 100 meters in open field. Indoors, it may be reduced to 30-50 meters depending on obstacles.
Can I connect a non-D-Link Bluetooth device?
Yes, the DBT-900AP is compatible with any standard Bluetooth device (headsets, keyboards, phones, etc.) complying with Bluetooth 2.0 or later.
How many devices can be connected simultaneously?
The access point supports up to 7 active Bluetooth devices at the same time.
How to reset the DBT-900AP to factory settings?
Press and hold the reset button on the back of the device for about 10 seconds using a paperclip. The LEDs will flash to confirm the reset.
What to do if my device does not connect?
Check that Bluetooth is enabled on the device, the PIN code is correct (default 0000), and the access point is powered on. Try restarting both the device and the access point.
Does the DBT-900AP support Bluetooth Low Energy (BLE)?
No, it uses Bluetooth 2.0+EDR (Enhanced Data Rate) technology, which is not BLE compatible. For BLE devices, use a Bluetooth 4.0 or higher adapter.
How to update the firmware of the DBT-900AP?
Download the latest firmware from the D-Link website. Log in to the web interface, go to 'Administration' then 'Firmware Upgrade', and select the downloaded file.
Is it normal for the device to heat up?
Yes, slight warmth is normal during operation. Ensure the device is placed in a well-ventilated area, away from direct sunlight and heat sources.
What are the LED indicators and their meaning?
A solid green LED indicates power is connected. A blinking blue LED indicates Bluetooth pairing, becoming solid when a device is connected. An orange LED blinks during network activity.
User questions about DBT-900AP D-LINK
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Point in PDF format for free! Find your manual DBT-900AP - D-LINK and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DBT-900AP by D-LINK.
USER MANUAL DBT-900AP D-LINK
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : D-LINK
Model : DBT-900AP
Category : Access Point