Apocalypse AAP-800.2D Atom Plus - Receiver Deaf Bonce - Free user manual and instructions
Find the device manual for free Apocalypse AAP-800.2D Atom Plus Deaf Bonce in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | Car Audio Amplifier (Receiver) |
| Model | Apocalypse AAP-800.2D Atom Plus |
| Number of Channels | 2 |
| Power Output (RMS) | 200W x 2 @ 4Ω 400W x 2 @ 2Ω 800W x 1 @ 4Ω (bridged) |
| Power Output (Max) | 800W x 2 |
| Frequency Response | 10 Hz – 30 kHz |
| Input Sensitivity | 0.2V – 6V |
| Signal-to-Noise Ratio | ≥ 100 dB |
| Total Harmonic Distortion | < 0.01% |
| Low Pass Filter | 50 Hz – 250 Hz |
| Subsonic Filter | 15 Hz – 40 Hz |
| Bass Boost | 0 – 12 dB at 45 Hz |
| Damping Factor | > 200 @ 4Ω |
| Input Impedance | 10 kΩ |
| Dimensions (L x W x H) | 11.8 x 7.5 x 2.2 inches (300 x 190 x 55 mm) |
| Weight | 5.5 lbs (2.5 kg) |
| Power Supply Voltage | 10 – 16 VDC |
| Operating Current | Up to 60A (fuse rating 60A x 1) |
| Protection Circuitry | Thermal, Overload, Short Circuit, DC Offset |
| Remote Turn-On | Yes (12V trigger) |
| Cooling | Convection with heatsink |
| Speaker Impedance (Stereo) | 2 – 8 Ω (stable at 2Ω) |
| Speaker Impedance (Bridged) | 4 – 8 Ω |
| Maintenance | Clean with dry cloth; ensure ventilation; check connections periodically |
| Safety | Disconnect battery before installation; use appropriate wire gauge; fuse protection |
Frequently Asked Questions - Apocalypse AAP-800.2D Atom Plus Deaf Bonce
What is the power output of the Apocalypse AAP-800.2D Atom Plus?
The amplifier delivers 200W RMS per channel at 4Ω, 400W RMS per channel at 2Ω, and 800W RMS bridged at 4Ω.
What is the minimum speaker impedance for stereo mode?
The amplifier is stable down to 2Ω per channel in stereo mode. For bridged mode, minimum impedance is 4Ω.
What type of power supply does it require?
It requires a 12V DC automotive electrical system, with a voltage range of 10-16V. Use a fused power wire (at least 60A).
Does the amplifier have built-in filters?
Yes, it includes a low-pass filter (50-250 Hz), a subsonic filter (15-40 Hz), and a bass boost (0-12 dB at 45 Hz).
How do I connect multiple speakers?
For two speakers, connect one to each channel at 2Ω or higher. To bridge, connect a single subwoofer to the positive of channel 1 and negative of channel 2, ensuring impedance is at least 4Ω.
What protection features does it have?
The amplifier includes thermal overload, overload, short circuit, and DC offset protection to prevent damage.
Can I use this amplifier with a factory stereo?
Yes, but you may need a line output converter if your factory stereo lacks RCA pre-outs. The input sensitivity (0.2-6V) allows compatibility.
What is the recommended fuse size?
Use a 60A fuse on the power wire near the battery. The amplifier itself has a built-in fuse of the same rating.
How should I mount the amplifier?
Mount it on a flat, solid surface with good ventilation. Avoid damp or hot areas. Use the included screws but do not block the heatsink.
Why does my amplifier go into protection mode?
Common causes: low impedance (below 2Ω stereo or 4Ω bridged), overheating, short circuit in speaker wires, or low battery voltage. Check connections and impedance.
User questions about Apocalypse AAP-800.2D Atom Plus Deaf Bonce
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual Apocalypse AAP-800.2D Atom Plus - Deaf Bonce and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Apocalypse AAP-800.2D Atom Plus by Deaf Bonce.
USER MANUAL Apocalypse AAP-800.2D Atom Plus Deaf Bonce
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Deaf Bonce
Model : Apocalypse AAP-800.2D Atom Plus
Category : Receiver