NSW200-28P - Switch ZYXEL - Free user manual and instructions
Find the device manual for free NSW200-28P ZYXEL in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Managed PoE+ Switch |
| Brand | ZyXEL |
| Model | NSW200-28P |
| Ports | 24x 10/100/1000 Mbps PoE+ ports, 4x Gigabit SFP uplink ports |
| PoE Standard | IEEE 802.3af/at |
| PoE Power Budget | 370W |
| Switching Capacity | 56 Gbps |
| Forwarding Rate | 41.7 Mpps |
| MAC Address Table | 8K entries |
| VLAN Support | Up to 4094 VLAN IDs |
| Management | Web-based GUI, SNMP, CLI (Telnet/SSH) |
| Dimensions (WxDxH) | 440 x 200 x 44 mm (19-inch rackmount) |
| Weight | 3.5 kg |
| Power Supply | Internal, AC 100-240V, 50-60Hz |
| Fan | Smart fans with temperature control |
| Operating Temperature | 0°C to 50°C |
| Storage Temperature | -40°C to 70°C |
| Humidity | 10% to 90% non-condensing |
| Safety Certifications | CE, FCC, RoHS |
| Mounting | 19-inch rackmount kit included |
| Warranty | 2 years |
Frequently Asked Questions - NSW200-28P ZYXEL
How to reset the switch to factory defaults?
Press and hold the reset button on the front panel for 10 seconds until the LEDs blink. Release to restore factory settings.
Does it support PoE and what is the total power budget?
Yes, it supports IEEE 802.3af/at PoE+ on all 24 ports. The total PoE power budget is 370W, with up to 30W per port.
How to access the web management interface?
Connect to the switch via a LAN port. Open a browser and enter the default IP address 192.168.1.1. Log in with default credentials (admin/admin).
Can I use SFP modules for fiber connections?
Yes, the switch has 4 dedicated SFP slots supporting Gigabit SFP modules (copper or fiber). They do not provide PoE.
How to configure VLANs on the NSW200-28P?
Access the web GUI, go to VLAN Configuration. You can create up to 4094 VLANs, assign ports, and set tagged/untagged members.
What is the maximum PoE power per port?
Each PoE+ port can deliver up to 30W per port, subject to total power budget of 370W.
Does the switch support link aggregation (LACP)?
Yes, it supports IEEE 802.3ad link aggregation. You can create up to 8 trunk groups with up to 8 ports each.
How to update the firmware?
Download the latest firmware from ZyXEL website. In the web GUI, go to Maintenance > Firmware Upgrade and upload the file. Do not power off during update.
Is there a console port for CLI access?
Yes, the switch has a RS-232 console port (DB9) for direct CLI access. Use a serial cable with settings 115200 baud, 8 data bits, no parity, 1 stop bit.
What do the LED indicators mean?
Power LED: solid green when on. PoE LED: green when PoE is active on a port. Link/Act: green for link, blinking for activity. SFP: green when module is detected.
User questions about NSW200-28P ZYXEL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Switch in PDF format for free! Find your manual NSW200-28P - ZYXEL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. NSW200-28P by ZYXEL.
USER MANUAL NSW200-28P ZYXEL
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ZYXEL
Model : NSW200-28P
Category : Switch