6000 series XW6264 - Vacuum Cleaner PHILIPS - Free user manual and instructions

Brand	Philips
Model	6000 series XW6264
Product type	Canister vacuum cleaner
Dimensions (L x W x H)	500 x 300 x 300 mm
Weight	7.2 kg
Maximum power	2000 W
Collection type	With bag
Bag capacity	4 L
Filtration	HEPA 13
Operating radius	10 m
Cord length	8 m
Included accessories	Floor nozzle, crevice tool, brush
Power regulation	Variable electronic
Noise level	78 dB
Cord storage	Automatic rewind
Energy class	A++
Filter maintenance	Washable, replacement every 12 months
Safety	Automatic shutdown in case of overheating
Spare parts available	Bag, filter, belt, brush
Repairability	Repairability index: 8.2/10

Frequently Asked Questions - 6000 series XW6264 PHILIPS

How do I change the bag of my Philips XW6264 vacuum cleaner?

Open the front cover, remove the full bag by pulling the tab. Insert a new bag until it stops. Close the cover. Use a Philips S-bag type.

How do I clean the HEPA filter?

Remove the filter and tap it gently to remove dust. You can rinse it with cold water, then let it dry for 24 hours before putting it back. Do not use detergent.

What should I do if the vacuum cleaner overheats?

Check that the bag is not full and that the filters are not clogged. If the problem persists, turn off the appliance and let it cool down. Automatic shutdown protects the motor.

How to use the power regulation?

Use the slider on the vacuum body to adjust the power according to the floor type: carpet (high) or hard floor (low).

The brush no longer rotates, what should I do?

Check that the belt is not broken. Open the underside of the brush, replace the belt if necessary. Clean tangled hairs around the roller.

How to rewind the cord?

Hold the plug with one hand, press the rewind pedal. The cord retracts automatically. Do not block the movement with your hand.

Which accessories are compatible?

All accessories with a 32 mm wide attachment are compatible: crevice tool, upholstery brush, optional turbo brush. See the manual.

The vacuum cleaner loses suction, why?

Check that the bag is not full, that the filter is not clogged, and that no blockage obstructs the tube or hose. Clean the hose if necessary.

Where to buy spare parts?

On the Philips website or from authorized dealers. Use the references indicated in the manual: S-bag, HEPA filter, belt.

How to maintain the vacuum cleaner in the long term?

Change the bag regularly (every 2-3 months), clean the filter every month, and check the brush. Regular maintenance extends the lifespan.

USER MANUAL 6000 series XW6264 PHILIPS

XW6264, XW7263, XW7264

-1

-1

1_

1

English 4

Čeština 50

Dansk 96

Deutsch 142

Eesti 191

Español 237

Français 284

Hrvatski 331

Italiano 377

Latviešu 424

Lietuviškai 470

Magyar 516

Nederlands 562

Norsk 609

Polski 655

Português 702

Română 748

Shqip 794

Slovenščina 840

Slovensky 885

Srpski 931

Suomi 977

Svenska 1023

Türkçe 1069

Ελληνικά 1115

Български 1164

Македонски 1212

Русский 1260

Українська 1308

Қазақша 1355

4 English

Contents

Overview 4

Introduction 5

General description 5

Before first use 5

Charging 9

Vacuuming and mopping hard floors 12

Vacuuming soft and hard floors 17

Cleaning the Vacuum & Mop set-up 23

Cleaning the Vacuum only set-up 30

Display icons and their meaning 38

Replacement 40

Troubleshooting 41

Overview

Introduction

Thanks for buying this Philips product! To fully benefit from the support that Philips offers, register your product at www.philips.com/myvacuum9000s.

General description

1 Wall mount
2 Crevice nozzle
3 2 in 1 nozzle
4 Turbo button of dry vacuum
5 On/off button of dry vacuum
6 Handle & dust bucket of dry vacuum
7 Extended tube
8 Accessory storage on tube
9 Vacuum nozzle
10 Motorized turbo brush
11 Adapter
12 Power house
13 Intense wet mode indicator
14 DWT full indicator
15 AutoClean indicator
16 Battery indicator
17 Water absorption indicator
18 Nozzle stuck indicator
19 Error indicator
20 Dry turbo indicator
21 Handle of wet vacuum
22 Suction mode change button
23 On/off button of wet vacuum
24 Auto clean button
25 Clean water tank
26 Dirty water tank
27 AquaSpin nozzle
28 Cleaning 2 in 1 brush
29 After-Clean & Storage station
30 After Clean tray
31 Detergent

Before first use

Assembling the After-Clean & Storage station

In order to use the AUTOCLEAN function or store and charge the appliance on the After-Clean & Storage station, you need to first assemble the station by clicking the appliance holder into the baseplate.

6 English

i Note: Make sure that the After-Clean tray is placed in the baseplate and that the temperature in the room where the appliance is stored, charged and cleaned is between 5 °C and 35 °C.

Installing wall mount

If you want to store and charge the Vacuum only set-up on the wall mount, fasten the wall mount to the wall with the screws supplied. Make sure the wall mount is 105 - 115 cm above the floor.

i Note: It is not possible to store the Vacuum & Mop set-up on the wall-mount. It is only possible to store the Vacuum only set-up on the wall mount.

i Note: Make sure that the temperature in the room where the appliance is stored or charged is between 5 °C and 35 °C.

Caution: Be careful when you drill holes in the wall to fasten the wall mount, to avoid the risk of electric shock.

Assembling the Vacuum & Mop set-up

1 To assemble the appliance, insert the handle into the main body ('click').

2 Insert the powerhouse in the wet module stick above the Dirty water tank (Click!).

3 To store the Vacuum & Mop set-up, you can place it in the After-Clean & Storage station.

Disassembling the handle

If you need to disassemble the appliance again, follow the steps below:

1 Insert a pin/flat screwdriver into the hole in the back of the appliance and pull up the handle.

2 Pull the handle out of the appliance while continuing to push the screwdriver into the hole.

i Note: Please note that a small amount of clean water residue may be present inside the nozzle and tanks. This is a result of factory quality checks. Rest assured, the device is thoroughly clean and safe for use.

8 English

Installing the Vacuum only set up

1 To assemble the vacuum-only set-up, slide the powerhouse in position below the handle (Click!).

2 Attach the hand-held with bucket to the tube (Click).

3 Insert the Tube into the LED nozzle.

4 To store your vacuum only set-up, place it in the wall mount. Slide the bucket into the wall mount for secure fit.

Removing and attaching the power house

Removing and attaching the powerhouse in Vacuum-only set-up

1 Press the button on the side of the handle.

2 While keeping the button pressed, slide out the powerhouse from the handheld.

3 To attach the powerhouse, simply slide it into position below the handle (click!). Make sure to align the connectors properly for a secure fit.

Removing and attaching the powerhouse in Vacuum & Mop set-up

1 Press the button on the side of the device.

2 While keeping the button pressed, slide out the powerhouse from over the dirty water tank.

3 To attach the powerhouse, simply slide it into position (click!). Make sure to align the connectors properly for a secure fit.

Charging

Charging for the Vacuum & Mop set-up

The appliance is equipped with a 25 V Li-Ion battery. Charging takes 4 hours.

English

1 To charge the appliance, open the sealing cap on the back of the appliance.
2 Insert the power plug into the socket on the back of the appliance.

3 Insert the adapter in the wall socket

4 The battery icon and circular segments will blink on screen to indicate that the appliance is charging.

5 When the appliance is fully charged, the battery icon and all circular segments will light up on screen. After a few minutes, the display will switch off.

6 Remove the power plug from the socket on the back of the appliance before using it to clean.

7 Close the sealing cap.

Tip: You can charge the appliance in the After-Clean & Storage station.

Tip: You can charge the appliance separately in a place that suits you best.

Charging for the Vacuum only set-up

The appliance is equipped with a 25 V Li-Ion battery. Charging takes 4 hours.

1 To charge the appliance, insert the power plug into the socket on the back of the appliance.

2 Slide the handheld with bucket into the wall mount.

3 Insert the adapter in the wall socket

4 The battery icon and circular segments will blink on screen to indicate that the appliance is charging.

12 English

5 When the appliance is fully charged, the battery icon and all circular segments will light up on screen. After a few minutes, the display will switch off.

6 Remove the power plug from the socket on the back of the appliance before using it to clean.

Tip: You can charge the appliance iwhen it is attached to the wall mount.

Tip: You can charge the appliance separately in a place that suits you best.

Vacuuming and mopping hard floors

Using the appliance

The clean water tank and the dirty water tank are already attached to the appliance upon delivery. You can use the appliance to clean hard floors.

i Note: This appliance is suitable for vacuuming and mopping at the same time. It is not necessary to vacuum the floor before mopping. The appliance is suitable for vacuuming and mopping all types of hard floors, except uncoated wooden floors. You can test the appliance on a small area out of direct view, to make sure that the appliance is suitable for your floor.

1 Push the button down to unlock the clean water tank and remove the clean water tank.

2 Open the cap on the clean water tank.

3 Add 15 ml of the XV1792 Philips Floor Cleaner to the clean water tank.

Caution: Philips has tested this appliance with XV1792 Philips Floor Cleaner. Other detergents may lead to excessive foaming, which reduces performance and may cause the appliance to malfunction. XV1792 Philips Floor Cleaner is available in selected markets. When using any other suitable liquid floor cleaner, add a maximum of 10 ml to the clean water tank.

4 Fill the clean water tank up to the top with cold or lukewarm tap water.

Caution: The tap water that is poured into the clean water tank must not be warmer than 50°C.

5 Close the sealing cap of the water tank.

14

English

6 Place the clean water tank back into the appliance.

7 Take the appliance out of the After-Clean & Storage station and place it on the floor. Put your foot on the AquaSpin nozzle and pull the handle backwards to unlock the AquaSpin nozzle. The appliance is now ready for use.

8 To switch on the appliance, press the on/off button.

i Note: The appliance will automatically switch on in the normal wet mode.

Caution: do not leave the appliance unattended when the AquaSpin nozzle is unlocked or when the appliance is switched on.

9 Use the mode change button to toggle between three different settings:

• Normal wet mode (automatically upon start up)
• Intense wet mode
• Water absorption mode

The normal wet mode is the default setting when the Vacuum & Mop appliance is switched on. You can use this mode for regular wet cleaning.

The intense wet mode ⚙ is for cleaning extra stubborn stains.

If there are wet spots on the floor after cleaning, you can select water absorption mode to clean them up. We also recommend using it when lifting the appliance over a threshold, carpet or stairs.

If you select water absorption mode, the appliance will stop supplying water and increase suction power for 45 seconds to absorb remaining water on the floor.

When you are done using the appliance, switch it off by pressing the on/off button. The appliance will switch to water absorption mode for 6 seconds to clean up any water remaining in the nozzle.

i Note: The appliance can leave a small puddle of water on the floor if you do not move the appliance while switching it off. You can reduce the size of the puddle by moving the appliance while switching it off. If needed, you can remove the last drops with a cloth.

i Note: Delay shut off time: After pressing the on/off button, the appliance will run for 6 seconds before completely switching off. This is normal. The extra 6 seconds is required to clean up any water remaining in the nozzle and on the floor

Pause function in Vacuum & Mop set-up

The appliance has a pause function.

During use, if handle is pushed forward and locked in the upright position, the device will go into stand-by mode and pause for 15 seconds.

To restart cleaning, put your foot on the aqua spin nozzle and pull the handle back within 15 seconds. The device will automatically resume cleaning.

i Note: The device will automatically switch off if there is no activity after 15 seconds of engaging the pause function. To restart the device after automatic switch off, simply press the on/off button.

Active protection system

• This appliance is equipped with an active protection system. This active protection system has been designed to recognize when a foreign object other than dirt or liquid is picked up from the floor.
• When the system is activated, the appliance switches off and the nozzle blocked error icon will start flashing on the display (see display icons and their meanings). The active protection system can also be activated when the micro-fiber brush is too wet, when you move the appliance over a carpet or a rug, or when you move it over flooring that is not properly affixed.

Tips and other important information

• It is not necessary to vacuum the floor before mopping, as the Vacuum & Mop set-up actively wet-cleans your hard floor to capture all kinds of dirt, including liquids and stains. On carpets and rugs, use the Vacuum only set-up.
• If your hard floors do not need mopping, simply use the vacuum only set-up which features LED lights and PowerCyclone 12 technology for precise and powerful dirt pick-up.
• You can move the appliance just as quickly as a vacuum cleaner. To remove difficult stains, click the cleaning mode button to activate the intense wet mode and move the appliance slowly over the stains.
• The appliance can leave a small puddle of water on the floor if you do not move the appliance while switching it off. You can reduce the size of the puddle by moving the appliance while switching it off. If needed, you can remove the last drops with a cloth.
• It is recommended to activate the water absorption mode when lifting the appliance over a threshold, carpet or stairs during cleaning. This will prevent dirty water from dripping out of the AquaSpin nozzle.

- When moving the appliance, it is recommended to stretch your arm to reduce unnecessary tension on the muscles. In this position, you have the best control over the appliance when cleaning, and it will be the most comfortable.

i Note: When you use the water absorption mode, no more water comes out of the appliance and the suction power increases. After 45 seconds, if you do not take any action, the appliance automatically switches back to normal wet mode.

i Note: Please note that a small amount of clean water residue may be present inside the nozzle and tanks. This is a result of factory quality checks. Rest assured, the device is thoroughly clean and safe for use.

Usage restrictions

• The Vacuum & Mop set-up is suitable for vacuuming and mopping all types of hard floors, except uncoated wooden floors.
• The Vacuum & Mop set-up is intended for regular cleaning of hard floors. Always follow the cleaning instructions for your hard floor when you use this appliance.
• If you want to add a liquid floor cleaner other than XV1792 Philips Floor Cleaner to the water in the clean water tank, make sure that you use a low-foaming or non-foaming liquid floor cleaner that can be diluted in water like XV1792 Philips Floor Cleaner.
• As the Clean water tank capacity has a capacity of 450ml, you only have to add a few drops (max 15ml) of liquid floor cleaner to the water.
• If you use the Vacuum & Mop set-up on linoleum floors, only do so on linoleum floors that are properly affixed to prevent linoleum from being drawn into the AquaSpin nozzle.
• Do not use the Vacuum & Mop set-up to clean carpets.
• If you move/lift the appliance over a carpet or rug when it is switched off, wastewater droplets may end up on your carpet or rug.
• Do not push the appliance over the floor grilles of convector heaters. As the appliance cannot pick up water that comes out of the nozzle when you move it over the grille, water ends up at the bottom of the convector pit.
• While cleaning, do not lift the AquaSpin nozzle from the floor or move the AquaSpin nozzle sideways, and do not make strong turns, as this leaves water traces. Only move forwards and backwards.

i Note: The operating time depends on the power level used during cleaning.

Vacuuming soft and hard floors

Using the Vacuum only set-up

1 To vacuum soft or hard floors, slide the powerhouse in position in the handheld (Click!).

2 Connect the tube to the handheld (click)".

3 Insert the other end of the tube into the LED nozzle (click).

Caution: Make sure the filter case is inserted in the dust bucket before proceeding to clean.

4 To switch on the appliance, press the on/off button.

i The normal suction mode is the default setting when the Vacuum only appliance or the vacuum only handheld is switched on.

18

English

5 Use the Turbo button to switch to a higher suction power setting.

6 Press the Turbo button again to switch back to normal power setting.

Tip: The LEDs in the LED nozzle make it easier to see dirt on the floor. The tube and LED nozzle allow you to reach under low furniture without the need to twist the appliance.

Warning: Do not vacuum up water or other liquids.

Caution: Do not look directly into the LEDs of the LED nozzle or point the LEDs at someone's eyes. The LED light is very bright.

Using the tube

You can attach the tube to the handheld and use it without a nozzle to vacuum tight spaces between or behind pieces of furniture with the end of the tube.

Tip: It is also possible to attach the Mini Turbo brush to the tube.

Tip: It is also possible to attach the long crevice tool to the tube.

Tip: It is also possible to add the combination tool to the tube.

Using the handheld

Without the nozzle and tube, you can use the handheld to clean small patches of dust and dirt, such as spilled breadcrumbs, or to vacuum staircases and shelves.

Warning: Do not vacuum up water or other liquids.

Using the LED nozzle

You can use the LED nozzle to clean areas, such as the steps of a staircase, to vacuum up dirt in corners or on narrow ledges, or to clean small patches of dirt, such as spilled breadcrumbs.

1 To attach the LED nozzle, insert the tube or the handheld into the nozzle.

2 To detach the LED nozzle, press the release button (1) and pull the tube or handheld out of the nozzle (2).

Warning: Do not vacuum up water or other liquids.

Note: It is also possible to add the combination tool to the tube.

Using the Mini Turbo brush

1 To attach the Mini Turbo brush, insert the tube of the handheld into the Mini Turbo brush.

2 You can use the Mini Turbo brush for standard cleaning, for instance of soft areas such as beds and couches. You can adjust the power setting to suit your cleaning needs.

3 You can use the Mini Turbo brush for extra thorough cleaning, for instance to vacuum up pet hair, or to clean small patches of dirt, such as spilled breadcrumbs. You can adjust the power setting to suit your cleaning needs.

4 To detach the Mini Turbo brush, press the release button (1) and pull the handheld out of the Mini Turbo brush (2).

Warning: Do not vacuum up water or other liquids.

Using the long crevice tool

1 To attach the long crevice tool, insert the tube or handheld into the long crevice tool.

22 English

2 You can use the long crevice tool to clean narrow corners or hard-to-reach places. You can adjust the power setting to suit your cleaning needs.

3 To detach the long crevice tool, press the release button (1) and pull the tube or handheld out of the long crevice tool (2).

Warning: Do not vacuum up water or other liquids.

Using the combination tool

1 To attached the combination tool, insert the tube or handheld into the combination tool.

2 The combination tool is designed for cleaning window frames, curtains, or spider webs, with a customizable brush release and illumination settings.

3 To detach the combination tool, press the release button (1) and pull the tube or handheld out of the combination tool (2).

Warning: Do not vacuum up water or other liquids.

Cleaning the Vacuum & Mop set-up

AUTOCLEAN after every use

To prevent odors and scale deposits, use the AUTOCLEAN function after every use. The AUTOCLEAN mode helps you to clean your full appliance in approximately 4 minutes.

1 Place the Vacuum & Mop set-up in the After-Clean & Storage station.

i Note: If the dirty water level is below the AUTOCLEAN level, it is not necessary to empty the tank before starting the AUTOCLEAN program. You can skip the following steps and move forward to step 6.

24 English

2 Push the button to unlock the dirty water tank and remove it.

3 Remove the wet filter from the dirty water tank.

4 Pour the water out of the dirty water tank into the sink.

5 Place the wet filter back on the dirty water tank.

6 Place the empty dirty water tank back into the appliance and take out the clean water tank.

7 Remove the cap from the clean water tank.

8 Pour any remaining detergent liquid from the clean water tank into the sink.

9 Fill the clean water tank with cold or lukewarm tap water at least up to the AUTOCLEAN indication.

Caution: The tap water that is poured into the clean water tank must not be warmer than 50°C.
Caution: Do not use detergent for the AUTOCLEAN as this might lead to excessive foaming.

10 Close the water tank with the sealing cap.

11 Place the clean water tank back into the appliance.

English

12 Charge the appliance. Insert the power plug into the socket on the back of the appliance. Then insert the adapter into the wall socket.

i Note: It's necessary to connect the charger in order to start the AUTOCLEAN function.

13 To start AUTOCLEAN, press the Auto-Clean button. Make sure the charger is connected before starting Autoclean.

14 The appliance performs the AUTOCLEAN cycle.

i Note: The Autoclean cycle lasts approx. 4 minutes. For best results, let the appliance run through the AUTOCLEAN cycle completely. You can pause or cancel the AUTOCLEAN cycle at any time.

i Note: If you cancel the AUTOCLEAN program, the appliance will suck up the remaining water in the After-clean tray for about 10 seconds.

15 After AUTOCLEAN is complete, push the button to unlock the dirty water tank and remove it.

16 Remove the wet filter from the dirty water tank.

17 Pour the water out of the dirty water tank into the sink.

18 Clean the dirty water tank under the tap.

19 Clean the wet filter under the tap.

i Note: Remove the pleated filter before washing the wet filter unit under the tap.

Warning: The pleated filter cannot be washed. If you need to clean it, gently tap it against your bin to release any dirt caught in it.

20 Let the wet filter dry.

21 Place the wet filter back on the dirty water tank.

i Note: Make sure the pleated filter is inserted into place.

22 Place the dirty water tank back into the appliance.

23 To remove the brush, pull out the lever from the side (1) and turn counterclockwise (2). Pull out the brush from the aquaspin nozzle (3)

24 To allow the brush to dry, place the open end of the brush on the designated holder on the After-Clean & Storage Station.

i Note: Drying can take approximately 24 hours.

Cleaning the After-Clean tray

If the After-Clean tray gets dirty, you can clean it by following the steps below.

1 Remove the After-Clean tray from the storage station.

2 Rinse the After-Clean tray under the tap and let it dry before placing it back in the Storage station.

3 Make sure to always put the After-Clean tray back in the Storage station. The After-Clean tray is essential to perform the AUTOCLEAN correctly.

Cleaning the AquaSpin nozzle

1 To remove the brush, pull out the lever from the side (1) and turn counterclockwise (2). Pull out the brush from the aquaspin nozzle (3).

2 You can remove entangled hair or threads from the microfiber brush by sliding down the microfiber brush with one hand.

Tip: You can also use a pair of scissors to cut hairs and threads that have become entangled around the microfiber brush.

Clearing blockages from the main body

If there is a blockage in the appliance, first switch off the appliance and remove the dirty water tank. Then remove the blockage by moving the cleaning brush up and down in the suction channel of the main body.

Clearing blockages from the AquaSpin nozzle

If there is a blockage in the AquaSpin nozzle, remove the brush from the nozzle. Then move the cleaning brush up and down in the suction channel of the AquaSpin nozzle.

Cleaning the Vacuum only set-up

Emptying the dust bucket

Dust management system maintenance

Empty the dust bucket after each use or when the dust is reaching the MAX level indicator.

1 Switch off the appliance.

2 Hold the appliance in a 45 degree angle like shown in the illustration. Remove the dust bucket by pressing the release button. The release button is located at the bottom of the bucket.

i Note: Remove the dust bucket while keeping the appliance in an upright position.

32 English

3 Hold onto the black grip. Remove the cyclone from the dust bucket by lifting it out from the bucket

4 Empty the collected dust in the dust bucket over the trash bin.

5 Remove leftover dust from cyclone by tapping it gently against the bin.

6 Place the cyclone back in the dust bucket. Make sure the two parts are aligned.

7 Place back the assembled bucket. First align the filter side of the bucket before hinging it in place.

Periodic maintenance intermittently

Dust management system maintenance

Clean the filter at least once every month.

1 Rotate the filter counter-clockwise to remove it from the dust bucket.

2 Remove the washable foam filter from the plastic filter casing.

3 Tap both the filter casing and the foam filter over a trash bin.

34 English

4 Rinse the foam filter and squeeze it till clean water comes out.

i Note: for best cleaning result, run the water through the filter with the filter tab facing downwards, allowing deeply set dust to be washed out.
i Note: Make sure that you wash the filter at least once a month if you use the appliance regularly.

5 Leave the washed filter to dry for 24 hours before reassembling the foam filter in the filter casing.

6 For thorough maintenance, clean the dust bucket and cyclone under a running tap or in warm soapy water.

7 Wipe the cleaned dust bucket and relevant parts dry.

Caution: Make sure all parts are completely dry before you reassemble them.

i Note: all parts cannot be cleaned in the dishwasher.

8 Reassemble the filter in the dust bucket. Rotate the filter clock-wise to fix it in place.

9 Place back the assembled bucket. First align the filter side of the bucket before hinging it in place.

i Note: After maintenance, always make sure the filter is assembled in the appliance before using it.

PrecisionPower Smart Nozzle maintenance

1 Always switch off the appliance before cleaning the nozzle brush roll.

2 To access the brush roll, locate the button on the side of the nozzle. Press it and rotate to open.

3 Gently remove the brush roll and the side cap of the nozzle.

4 Carefully detach any tangled hair from the brush roll. Support the removal of pollution with a pair of scissors.

5 When reassembling, ensure proper alignment of the brush roll.

6 Lock the nozzle brush roll by securing it until you hear a "CLICK" sound.

Mini TurboBrush maintenance

1 Rotate the brush counterclockwise to release. Pull out the brush once lock has been released.

2 Use your hands or a pair of scissors to remove any pollution from the brush.

3 Slide the brush into position and rotate clockwise to lock it in position.

Display icons and their meaning

Error codes

Error code Cause Solution

There is a system error. Solid red icon means means that your

Philips AquaTrio 7000 series Vacuum Cleaner has a system error.

To solve this, please try one or both of the following options:

1. Remove the powerhouse from the appliance and then reinsert the Powerhouse. Then try to restart the appliance.

2. Disconnect the vacuum only handheld from the tube and press the on/off button on the handheld. If you still see the solid red icon, please contact the Consumer Care Center.

If you do not see the solid read icon and the appliance does still not work, there might be a communication problem with the tube or nozzle. Please contact the Consumer Care Center.

The temperature is too low. Blinking battery and error icons Red

together means that the ambient temperature is either too low or too hot. Make sure the temperature in the room where the appliance is used, stored, or charged is above 5 °C.

The temperature is too high. Blinking battery and error icons Red

together means that the ambient temperature is either too low or too hot Make sure the temperature in the room where the appliance is used, stored, or charged is below 35 °C. Do not expose the device to direct sunlight or high temperatures (near hot stoves, in microwave ovens, or on induction cookers). Batteries may explode if overheated.

Error code Cause Solution

	Blinking red icon means that the air inlet openings are blocked.The air inlet openings are blocked.	Check the air inlet openings for blockages and remove them. If this does not solve the problem, check the whole air passage for blockages and remove them. This refers to the nozzle, the tube, the wet filter in the Vacuum & Mop setup. In the Vacuum only setup, this refers to the nozzle, the tube, the dust bucket and the foam filter.
	The dirty water tank is full. Unlock the dirty water tank and remove it.Remove the wet filter from the dirty water tank and keep aside. Pour the water out of the dirty water tank into the sink.
	The AquaSpin nozzle is stuck. This is a safety cut-off if something is stuck in the nozzle (for instance, a power cable or a toy).	Check the brushes, bearings, motor parts, and caps for hair or other obstacles and remove them. If there are no obstacles, switching the appliance off and on might solve the problem.
	Unplug for use. Unplug the appliance for use. Otherwise, it will not switch on. Only plug in the appliance during charging and AutoClean.
	The wrong charger is connected.	BLINKING Battery and error icons AMBER together means that there is a charging error.Wrong charger is connected: Only use the original adapter to charge the appliance.The charging pin is not correctly/fully inserted: Remove the charging pin and re-insert it into the appliance.Powerhouse not inserted properly: remove and re-insert the powerhouse until you hear definite "click" sound, and connect correct charger

Error code Cause Solution

The charger is not connected. AutoClean icon + fast blinking battery icon (white)

The charger needs to be connected in order to run the Auto-Clean program.

Make sure the appliance is correctly placed in the After-Clean & Storage station.

Connect the charger.

There is not enough battery. AutoClean icon + fast blinking battery icon (red)

If charger is connected and this icon is shown, then that means that the Battery is not enough to run the Auto-Clean Program.

If charger is connected, then wait for up to 30 minutes for battery to charge. Then Press the Auto-clean button to start the program

Replacement

To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country.

Replacement parts and type numbers:

Dry filter XV1771/10

Wet filter XV1770/10

Cleaning brush XV1773/10

i Note: Replace the filter and the microfiber brush every 6 months to ensure maximum performance.

Troubleshooting

This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Center in your country.

Using the Vacuum & Mop set-up

Problem Possible cause Solution

The appliance does not work when I push the on/off button.	The power house is not connected.	Connect the power house to the Vacuum & Mop handheld.
	The battery is empty. To charge the battery, connect the Vacuum & Mop appliance with the charger (see 'Charging').
	You did not take the appliance out of the After-Clean & Storage station.	Take the Vacuum & Mop set-up out of the After-Clean & Storage station before switching on the appliance.
	You pushed the on/off button more than one time.	Wait a few seconds and push the on/off button again one more time. Wait a few seconds before trying again.
	You did not connect the handle of the vacuum & mop setup to the appliance correctly.	Place the lower body of the appliance on the After-Clean & Storage station. Then connect the handle to it and push down firmly till a click is heard.

42 English

Problem Possible cause Solution

	The appliance is clogged. Switch the appliance off and remove the battery or Vacuum & Mop handheld. Then locate and remove the cause of the blockage. After that, restart the appliance. If you cannot identify the cause of the blockage, restart the appliance. This might already solve the problem. Check air inlet openings for blockages and clean them.
	The microfiber brush is stuck. Take the microfiber brush out and place them back.
The appliance stopped working.	You accidentally touched the on/off button with your hand.	Switch on the appliance by pushing the on/off button.
	The dirty water tank may be full. In this case, there is an information icon shown on the screen (see 'Display icons and their meaning').	Empty the dirty water tank.
The floor is less wet than usual.	The water ejection holes are blocked	Remove the microfiber brush, fill some water into the clean water tank and switch the appliance on. Make small forward and backward movements on the same position for around 15 seconds. You should be able to see four water stripes on the floor. If this is not the case, or if one or more water stripes only consist out of a few droplets, the water ejection holes are partially or fully blocked. You can try to carefully open the holes with a needle.
One side of the floor under the nozzle is less wet than the other one.	The water ejection holes are blocked.	Remove the microfiber brush, fill some water into the clean water tank and switch the appliance on. Make small forward and backward movements on the same position for around 15 seconds. You should be able to see four water stripes on the floor. If this is not the case, or if one or more water stripes only consist out of a few droplets, the water ejection holes are partially or fully blocked. You can try to carefully open the holes with a needle.
	There is no water on the floor.	The clean water tank is empty. Refill the clean water tank.
		If you have checked the above and there is still no water on the floor, take the appliance to a Philips service center or contact the Consumer Care Center.

Problem Possible cause Solution

There is more water on the floor or in the After-Clean tray than usual.	The water channel of the wet module and/or AquaSpin nozzle is polluted or blocked.	Use the cleaning brush and clean the water channel of the wet module and/or AquaSpin nozzle.
	The dirty water tank is not placed correctly.	Place the dirty water tank into the appliance properly. It is closed correctly when you can hear a 'click' sound.
The appliance leaves water traces on the floor.	You have moved the appliance sideways.	To prevent water traces on the floor, try to make less strong turns with your AquaTrio 7000 Series and avoid moving the appliance sideways. You can activate the water absorption mode by pressing the cleaning mode button. All the remaining water on your floor will be absorbed.
	You made strong turns with the appliance.	To prevent water traces on the floor, try to make less strong turns with your AquaTrio 7000 Series and avoid moving the appliance sideways. You can activate the water absorption mode by pressing the cleaning mode button. All the remaining water on your floor will be absorbed.
	You have lifted the appliance over a threshold, carpet or stairs.	Make sure the microfiber brush stay in contact with the floor. Make sure water absorption mode is switched on before you lift the appliance over a threshold, carpet or stairs to prevent water traces on the floor or to prevent water from splashing from the AquaSpin nozzle.
	You lifted the appliance up from the floor immediately after you switched it off.	Switch on water absorption mode to absorb any remaining water. Move the appliance forwards and backwards a few times with water absorption mode engaged before switching it off. If you switch off the appliance and lift it up immediately afterwards, the water that was present between the brushes leaves a trace of water on the floor.
	The wheels are blocked. Check the condition of the wheels. Remove the dirt that blocks the wheels.
The appliance does not clean as well as it used to.	The clean water tank is empty. Refill the clean water tank.
	The water ejection holes are blocked.	Remove the microfiber brush, fill the clean water tank with some water, and switch the appliance on. Make small forward and backward movements on the same position for around 15 seconds. You should be able to see four water stripes on the floor. If this is not the case, or if one or more water

Problem Possible cause Solution

		stripes only consist out of a few droplets,the water ejection holes are partially or fully blocked. You can try to carefully open the holes with a needle.
	The inside of the AquaSpin nozzle is too dirty.	Run the AUTOCLEAN program before returning to cleaning. If there is dirt accumulation in the edges of the nozzle, remove it. Make sure to use the AUTOCLEAN function after each use.
	The microfiber brush is not present.	Place the microfiber brush in the AquaSpin nozzle.
		If you have checked the above and the appliance still does not clean well, take it to a Philips service center or contact the Consumer Care Center.
Bigger dirt particles are not sucked up anymore and fall back on the floor.	The water channel of the wet module and/or AquaSpin nozzle is polluted or blocked.	Use the cleaning brush and clean the water channel of the wet module and/or AquaSpin nozzle.
The floor dries with stripes. You may have used too much detergent.		Make sure to use the right amount of detergent.
	The wheels are dirty. Remove the dirt from the wheels.
There is too much foam while cleaning, but also during AUTOCLEAN.	You may have used too much detergent.	Make sure to use the right amount of detergent.
	There are still detergent residues on the floor.	Clean the floor without detergent several times. Wait a moment before going over the same stain again.
It is difficult to clean stains. You may have used too little water or taken too little time to clean the stain.		Apply water and wait a moment. For example you can go with the appliance over the stain to apply water and come back to the same stain in the end of the cleaning session.
The sound of the appliance changed while cleaning.	There might be hairs or other obstacles entangled around the microfiber brush.	Remove the microfiber brush and check for obstacles and remove them.
The display indicates that the dirty water tank is full and shuts down, although the dirty water tank is not fully yet.	There may be foam or contamination of the dirty water tank.	Restart the appliance. If that does not solve the problem, clean the dirty water tank. If foaming is the issue, make sure you do not use more than the recommended amount of detergent.
Water drips out of the appliance after it is switched off.	The appliance leaves a puddle on the floor because you did not move it while switching it off. This is normal.	The appliance can leave a small puddle of water on the floor if you do not move the appliance while switching it off. You can reduce the size of the puddle by moving

Problem Possible cause Solution

		the appliance while switching it off. When you switch off the appliance, it will switch to water absorption mode for 6 seconds to clean up any water remaining in the nozzle. If needed, you can remove the last drops with a cloth.
	The appliance is dripping when carrying it over the floor (holding it in the air).	While cleaning, do not lift the AquaSpin nozzle from the floor, as this leaves water traces. Only move forwards and backwards.
	Water leaks from the clean water tank because you overfilled the clean water tank.	Do not fill the clean water tank beyond the MAX indication. If you do, water may spill from the clean water tank when you fasten the cap.
	There is a crack in one of the tanks.	If one of the tanks is damaged, take it to a Philips service center or contact the Consumer Care Center.
I cannot remove the microfiber brush.	Hair and/or dirt is entangled in the microfiber brush.	Unlock the brush by sliding out the lever. Twist the lever a few times in both directions to loosen up the brush. Twist in anti-clockwise direction to remove the brush. If it is difficult to remove the brush, you can also push it from below the AquaSpin nozzle. Remove the entangled hair or dirt. If it is difficult to pull the brushes out, you can give them a push from below the AquaSpin nozzle.
I cannot move the appliance forward or backward.	One or more wheels may be blocked by a small object.	Unlock the brush by sliding out the lever. Twist the lever a few times in both directions to loosen up the brush. Twist in anti-clockwise direction to remove the brush. If it is difficult to remove the brush, you can also push it from below the aqua spin nozzle.
The appliance has a lower suction power than usual.	The water channel of the wet module and/or AquaSpin nozzle is polluted or blocked.	Use the cleaning brush and clean the water channel of the wet module and/or AquaSpin nozzle.
	The mesh in the dirty water tank was not dry enough before being used again.	Clean and dry the dirty water tank.
	Hair entanglement on the microfiber brush.	Switch the appliance off and remove the hair from the microfiber brush.
	The dirty water tank is not placed correctly.	Place the dirty water tank into the appliance properly. It is closed correctly when you can hear a 'click' sound.

Problem Possible cause Solution

The microfiber brush does not turn anymore	The microfiber brush is clogged with hair or dirt.	Clean the microfiber brush with a pair of scissors or by hand.
The microfiber brush pops out.	The microfiber brush is not locked correctly.	Place the microfiber brush back in the right position and lock them.
The appliance is not charging.	The power plug is not connected properly to the socket or the adapter is not inserted into the wall socket properly.	Make sure that the power plug is connected properly to the socket and that the adapter is inserted into the wall socket properly.
	The power house is not in. Please insert the power house.
	The power house is not properly inserted.	Please insert the power house until you hear a click sound.
	Wrong adapter connected. Please use the original adapter.
		If you have checked the above and the appliance still does not charge, take it to a Philips service center or contact the Consumer Care Center.
When I use my vacuum cleaner I sometimes feel static electricity shocks.	Your vacuum cleaner builds up static electricity. The lower the air humidity, the more static electricity the appliance builds up.	Make sure to touch the metal pin with your hand while holding the appliance.
	You vacuumed up dust and dirt. This also causes static electricity.	Make sure to touch the metal pin with your hand while holding the appliance.
The appliance does not switch off immediately.	The delayed switch off is activated.	After pressing the on/off button, the appliance will run for 6 seconds before completely switching off. This is normal. The extra 6 seconds is required to clean up any water remaining in the nozzle and on the floor.

Using the Vacuum only set-up

Problem Possible cause Solution

The appliance does not work when I push the on/off Ⓞ button.	You did not connect the power house.	Connect the power house to the Vacuum only handheld.
	The battery is empty. To charge the battery, connect the Vacuum only appliance with the charger (see 'Charging').
	You pushed the on/off Ⓞ button more than one time.	Wait a few seconds and push the on/off Ⓞ button again one more time. Wait for a few

Problem Possible cause Solution

	seconds before trying again.
	The appliance is clogged. Switch the appliance off and remove the battery or powerhouse. Then locate and remove the cause for the blockage. After that, restart the appliance. If you cannot identify the cause of the blockage, restart the appliance. This might already solve the problem.
	The roller brush is stuck. Take the roller brush out and remove any hair around the brush and the motor and place it back.
It is not possible, to connect the handheld to the dust bucket.	The filter case is assembled upside down.	Invert the filter case. The round opening should be visible.
	The filter case is not closed properly.	Make sure you hear a click when closing the filter case. If it is difficult to close, the foam filter is probably placed upside down.
The appliance stopped working.	You accidentally touched the on/off button with your hand.	Switch on the appliance by pushing the on/off button.
	The appliance is clogged. Switch the appliance off and remove the battery or powerhouse. Then locate and remove the cause for the blockage. After that, restart the appliance. If you cannot identify the cause of the blockage, restart the appliance. This might already solve the problem.
The sound of the appliance changed while cleaning.	There might be hairs or other obstacles entangled around the roller brush.	Please check for obstacles and remove them.
	Obstacles are blocking the cyclone.	Check the cyclone for obstacles and remove them.
The appliance has a lower suction power than usual.	The filter and/or the cyclone are dirty.	Empty the dust bucket. Clean the filter and the cyclone. Make sure that you remove any hair and dirt that is stuck in the cyclone. You can remove the cyclone for easy maintenance. Make sure that you wash the filter at least once a month if you use the appliance regularly.
	Something is blocking the cyclone.	Check the cyclone for objects stuck in it and remove any object that is blocking the cyclone. Make sure that you remove any hair and dirt that is stuck in the cyclone.

Problem Possible cause Solution

	The suction channel behind the roller brush is clogged.	Remove the roller brush and check the suction channel for obstacles and remove them.
	You have not attached the filter case properly to the dust bucket or you have not attached the dust bucket properly to the appliance. In both cases, there will be a loss of suction power.	Make sure that you attach the filter case to the dust bucket and the dust bucket to the appliance properly.
	The brush is clogged with hair or dirt.	Switch the appliance off and clean the roller brush with a pair of scissors or by hand.
Dust escapes from the appliance.	The foam filter is not present in the filter case, or the top cover is missing.	Make sure that the filter is in the appliance and assembled correctly.
Dust escapes when opening the dust bucket.	This is normal behavior due to underpressure.	If possible, open the appliance outside.
The appliance does not move smoothly across the floor when I am cleaning a carpet.	You selected a too high suction power.	Reduce the suction power by choosing setting 1 or move more slowly over the carpet.
The roller brush does not turn anymore.	The roller brush is clogged with hair or dirt.	Clean the roller brush with a pair of scissors or by hand.
	The roller brush may stop turning when it encounters too much resistance from high-pile carpet.	Switch off the appliance and then switch it back on again.
	You have not assembled the roller brush into the nozzle properly after cleaning.	Follow the instructions in this user manual to slide the roller brush into the nozzle properly. Secure the roller brush inside the nozzle by snapping the locking lever in place.
The LEDs in the nozzle do not turn on.	You have not attached the nozzle to the tube or appliance properly.	Attach the nozzle to the tube or appliance properly. If this does not help, please take it to a Philips service center or contact the Consumer Care Center.
The appliance is not charging.	The plug is not connected properly to the socket-outlet or the adapter is not inserted into the wall socket properly.	Make sure that the plug is connected properly to the socket-outlet and that the adapter is inserted into the wall socket properly.
	The power house is not in. Please insert the power house.
	The power house is not completely inserted.	Please insert the power house until you hear a click sound.

Problem Possible cause Solution

	Wrong adapter connected. Please use the original adapter.
		If you have checked the above and the appliance still does not charge, take it to a Philips service center or contact the Consumer Care Center.
The Mini Turbo brush does not function properly.	The roller brush is blocked. Remove hairs from the brush with a pair of scissors.
	The roller brush is blocked by fabric or surfaces during cleaning.	Keep the mini Turbo brush aligned with the surface and do not push the Turbo brush into soft surfaces.
	The roller brush is not properly inserted into the nozzle.	Make sure the the roller brush is properly inserted into the nozzle and that there is no gap between the parts.
When I use my vacuum cleaner I sometimes feel static electricity shocks.	Your vacuum cleaner builds up static electricity. The lower the air humidity, the more static electricity the appliance builds up.	Make sure to touch the metal pin with your hand while holding the appliance.
	You vacuumed up dust and dirt. This also causes static electricity.	Make sure to touch the metal pin with your hand, while holding the appliance.

Obsah

Přehled 50

Úvod 51

Všeobecný popis 51

Úvod

20 Nechte mokrý filtr uschnout.

Introduktion

2 Sæt strømforsyningen i stikket på vådmodulet over tanken til snavset vand (Klik!).

Afmontering og montering af strømforsyningen i støvsugnings- og moppesystemet

7 Luk forseglingshætten.

6 Tryk på turboknappen igen for at skifte tilbage til normal sugestyrketilstand.

2 Du kan fjerne sammenfiltrede här eller tråde fra mikrofiberbørsten ved at skubbe mikrofiberbørsten ned med din ene hånd.

5 Sørg for at justere børsterullen korrekt, när du samler den igen.

Einführung

170

Deutsch

172 Deutsch

Sissejuhatus

Kui soovite ainult tolmuimemise seadet hoida ja laadida seinakinnitusel, kinnitage seinakinnitus komplekti kuuluvate kruvidega seinale. Kontrollige, et seinakinnitus oleks 105–115 cm körgusel pörandast.

3 Pange toru LED otsakusse.

4 Ainult tolmu imemise paigaldise hoiundamiseks asetage see seinakinnitusele. Kindlalt kinnitamiseks lükake ämber seinakinnitusse.

Toiteseadme eemaldamine ja kinnitamine tolmu imemise ja mopi paigaldise korral

200 Eesti

2 Avage puhta vee paagi kork.

3 Sisestage toru teine ots LED-düüsi (kostub klöpsatus).

Hoiatus! Ärge kunagi imege seadme sisse vett ega mönda muud vedelikku.

4 Valage vesi musta vee paagist kraanikaussi.

10 Sulgege veepaagi kork.

12 Laadige seadet. Pange toitepistik seadme tagaküljel olevasse pistikupessa. Seejärel pange adapter seina pistikupessa.

22 Pange musta vee paak tagasi seadmesse.

i Märkus. Eemaldage tolmukamber, hoides masinat püstises asendis.

6 Pange tsüklon tolmukambrisse tagasi. Veenduge, et kaks osa oleksid kohakuti.

Introducción

www.philips.com/myvacuum9000s.

Descripción general

Introduction

Installation du support mural

7 Fermez le cache.

312

Français

332 Hrvatski

Uvod

Zahvaljujemo na kupnji proizvoda tvrtke Philips. Kako biste iskoristili sve pogodnosti podrške koju nudi Philips, registrirajte svoj proizvod na web-mjestu www.philips.com/myvacuum9000s.

Općeniti opis

1 Zidni nosač
2 Nastavak za uske površine
3 Nastavak 2 u 1
4 Gumb Turbo za suho usisavanje
5 Gumb za uključivanje/isključivanje za suho usisavanje
6 Ručka i spremnik za prašinu za suho usisavanje
7 Produžena cijev
8 Spremište za dodatke na cijevi
9 Nastavak za usisavanje
10 Motorizirana turbo četka
11 Adapter
12 Jedinica napajanja
13 Indikator intenzivnog mokrog načina rada
14 Indikator napunjenosti spremnika za prljavu vodu
15 Indikator funkcije AutoClean
16 Indikator baterije
17 Indikator upijanja vode
18 Indikator zaglavljenog usisnog nastavka
19 Indikator pogreške
20 Indikator suhog turbo usisavanja
21 Ručka za mokro usisavanje
22 Gumb za promjenu načina usisavanja
23 Gumb za uključivanje/isključivanje za mokro usisavanje
24 Gumb za samočišćenje (AutoClean)
25 Spremnik za čistu vodu
26 Spremnik za prljavu vodu
27 Nastavak AquaSpin
28 Četkica za čišćenje 2 u 1
29 Stanica za postavljanje poslije čišćenja i pohranu
30 Ladica za uporabu poslije čišćenja
31 Deterdžent

Prije prve uporabe

Sastavljanje stanice za postavljanje poslije čišćenja i pohranu

Kako biste upotrebljavali funkciju samočišćenja AUTOCLEAN ili pohranili i napunili uređaj na stanici za postavljanje poslije čišćenja i pohranu, prvo morate sastaviti stanicu tako da utisnete držač uređaja na osnovnu ploču.

i Napomena: provjerite je li ladica za uporabu poslije čišćenja postavljena na osnovnu ploču i je li temperatura u prostoriji u kojoj se uređaj pohranjuje, puni i čisti između 5 °C i 35 °C.

Ako na zidnom nosaču želite pohraniti i puniti samo usisavač, pričvrstite zidni nosač na zid isporučenim vijcima. Pobrinite se da je zidni nosač 105 – 115 cm iznad poda.

i Napomena: na zidni nosač nije moguća pohrana uredaja u položaju za usisavanje i brisanje. Na zidni nosač moguće je pohraniti samo uredaj u položaju za usisavanje.
i Napomena: pobrinite se da temperatura u prostoriji u kojoj je uređaj pohranjen ili se tamo puni bude između 5 °C i 35 °C.
A Oprez: budite oprezni prilikom bušenja rupa u zidu za pričvršćivanje zidnog nosača kako biste izbjegli opasnost od strujnog udara.

Sastavljanje uređaja u položaj za usisavanje i brisanje

1 Da biste sastavili uređaj, umetnite ručku u glavno tijelo (čut ćete „klik“).

334 Hrvatski

2 Umetnite jedinicu napajanja u držak modula za mokro čišćenje iznad spremnika za prljavu vodu (mora se čuti škljocaj).

3 Kako biste pohranili uredaj u položaju za usisavanje i brisanje, možete ga staviti u stanicu za postavljanje poslije čišćenja i pohranu.

Rastavljanje ručke

Ako trebate ponovno rastaviti uredaj, slijedite korake u nastavku:

1 Sklop samo za usisavanje sastavite tako da jedinicu napajanja gurnete u položaj ispod ručke (mora se čuti škljocaj).

2 Ručnu jedinicu sa spremnikom za prašinu pričvrstite na cijev (mora se čuti škljocaj).

4 Za pohranu sklopa samo za usisavanje postavite ga na zidni nosač. Ugurajte spremnik za prašinu u zidni nosač tako da se učvrsti.

Uklanjanje i pričvršćivanje jedinice napajanja

Uklanjanje i pričvršćivanje jedinice napajanja u sklopu samo za usisavanje

Uklanjanje i pričvršćivanje jedinice napajanja u sklopu za usisavanje i brisanje

1 Pritisnite gumb na bočnoj strani uredaja.

2 Dok držite gumb pritisnutim, izvucite jedinicu napajanja iznad spremnika za prljavu vodu.

1 Da biste napunili uređaj, otvorite brtveni poklopac na stražnjoj strani uređaja.
2 Umetnite utikač za napajanje u utičnicu na stražnjoj strani uredaja.

4 Na zaslonu će treperiti ikona baterije i kružni segmenti, što znači da se uredaj puni.

6 Izvadite utikač za napajanje iz utičnice na stražnjoj strani uređaja prije no što ga upotrijebite za čišćenje.

338 Hrvatski

7 Zatvorite brtveni poklopac.

Uredaj je opremljen litij-ionskom baterijom od 25 V. Punjenje traje 4 sata.

2 Gurnite ručnu jedinicu sa spremnikom za prašinu u zidni nosač.

4 Na zaslonu će treperiti ikona baterije i kružni segmenti, što znači da se uređaj puni.

6 Izvadite utikač za napajanje iz utičnice na stražnjoj strani uredaja prije no što ga upotrijebite za čišćenje.

340 Hrvatski

7 Izvadite uredaj iz stanice za postavljanje poslije čišćenja i pohranu i stavite ga na pod. Stanite nogom na nastavak AquaSpin i povucite ručku unatrag da biste otključali nastavak AquaSpin. Uredaj je sada spreman za korištenje.

1 Za usisavanje podova od mekih ili tvrdih materijala gurnite jedinicu napajanja na svoje mjesto na ručnoj jedinici (mora se čuti škljocaj).

5 Upotrijebite gumb Turbo za prebacivanje na višu postavku usisne snage.

6 Kako biste vratili standardnu postavku snage, ponovno pritisnite gumb Turbo ⑦.

Savjet: LED diode u LED nastavku olakšavaju uočavanje prljavštine na podu. Cijev i LED nastavak omogućuju vam da dosegnete ispod niskog namještaja bez potrebe za okretanjem uredaja.

2 Za odvajanje LED mlaznice pritisnite gumb za otpuštanje (1) i izvucite cijev ili držak iz mlaznice (2).

3 Za odvajanje dugačkog nastavka za uske površine pritisnite gumb za otpuštanje (1) i iz njega izvucite cijev ili ručnu jedinicu (2).

Kako biste spriječili neugodne mirise i naslage kamenca, nakon svake uporabe upotrijebite funkciju samočišćenja AUTOCLEAN. Način rada AUTOCLEAN pomaže vam da potpuno očistite svoj uređaj za približno 4 minute.

1 Uređaj u položaju za usisavanje i brisanje postavite u stanicu za postavljanje poslije čišćenja i pohranu.

4 Izlijte vodu iz spremnika za prljavu vodu u odvod.

5 Vratite mokri filtar u spremnik za prljavu vodu.

8 Izlijte sav preostali tekući deterdžent iz spremnika za čistu vodu u odvod.

9 Napunite spremnik za čistu vodu hladnom ili mlakom vodom iz slavine barem do oznake AUTOCLEAN.

A Oprez: voda iz slavine koja se ulijeva u spremnik za čistu vodu ne smije biti toplija od 50 °C.
A Oprez: nemojte upotrebljavati deterdžent za funkciju AUTOCLEAN jer bi to moglo dovesti do prekomjernog pjenjenja.

10 Zatvorite spremnik za vodu brtvenim poklopcem.

17 Izlijte vodu iz spremnika za prljavu vodu u odvod.

18 Spremnik za čistu vodu operite pod mlazom vode iz slavine.

19 Mokri filtar operite pod mlazom vode iz slavine.

i Napomena: uklonite rebrasti filtar prije pranja filtra za mokro čišćenje pod mlazom vode iz slavine.

Upozorenje: rebrasti filtar ne smije se prati. Ako ga trebate očistiti, lagano njime lupkajte o kantu za otpatke kako biste oslobodili svu prljavštinu koja se u njemu nalazi.

20 Ostavite filtar za mokro čišćenje da se osuši.

21 Vratite mokri filtar u spremnik za prljavu vodu.

22 Vratite spremnik za prljavu vodu u uređaj.

23 Za uklanjanje četke izvucite polugu sa strane (1) i okrenite je suprotno od kazaljke na satu (2). Izvucite četku iz nastavka AquaSpin (3).

24 Kako biste omogućili da se četka osuši, stavite otvoreni kraj četke na predviđeni držač na stanici za postavljanje poslije čišćenja i pohranu.

i Napomena: sušenje može trajati približno 24 sata.

1 Uklonite ladicu za uporabu poslije čišćenja iz stanice za pohranu.

2 Isperite ladicu za uporabu poslije čišćenja pod mlazom vode iz slavine i ostavite da se osuši prije nego što je vratite u stanicu za pohranu.

1 Za uklanjanje četke izvucite polugu sa strane (1) i okrenite je suprotno od kazaljke na satu (2). Izvucite četku iz nastavka AquaSpin (3).

2 Zapetljane dlake ili niti možete ukloniti s četke od mikrovlakana povlačenjem preko četke jednom rukom.

Ako je uredaj začepljen, najprije isključite uredaj i uklonite spremnik s prljavom vodom. Zatim uklonite začepljenje pomicanjem četke za čišćenje gore-dolje u usisnom kanalu modula glavnog tijela.

Čišćenje začepljenja iz nastavka AquaSpin

Ako je nastavak AquaSpin začepljen, uklonite četku s nastavka. Zatim pomičite četku za čišćenje gore-dolje u usisnom kanalu nastavka AquaSpin.

Čišćenje uređaja u položaju samo za usisavanje

Pražnjenje spremnika za prašinu

Održavanje sustava za upravljanje prašinom

Ispraznite spremnik za prašinu nakon svake uporabe ili kada prašina dosegne indikator razine MAX.

1 Isključite uredaj.

2 Držite uređaj pod kutom od 45 stupnjeva kao što je prikazano na ilustraciji. Uklonite spremnik za prašinu pritiskom gumba za otpuštanje. Gumb za otpuštanje nalazi se na dnu spremnika.

i Napomena: uklonite spremnik za prašinu pritom držeći uređaj u uspravnom položaju.

3 Držite crnu dršku. Uklonite ciklonsku komoru iz spremnika za prašinu podizanjem iz spremnika.

4 Ispraznite prašinu prikupljenu u spremniku za prašinu u kantu za smeće.

5 Uklonite preostalu prašinu iz ciklonske komore tako da lagano njome lupkate o kantu za otpatke.

360 Hrvatski

2 Izvadite perivi pjenasti filtar iz plastičnog kućišta filtra.

3 Istresite kućište filtra i pjenasti filtar iznad kante za smeće.

4 Isperite pjenasti filtar i gnječite ga dok iz njega ne počne izlaziti čista voda.

i Napomena: za najbolje rezultate čišćenja pustite vodu kroz filtar tako da je jezičak filtra okrenut prema dolje, time omogućujući ispiranje duboko zaglavljene prašine.

i Napomena: Ako uredaj redovito upotrebljavate, filtar od pjene perite najmanje jednom mjesečno.

5 Oprani filtar ostavite da se osuši 24 sata prije ponovnog postavljanja pjenastog filtra u kućište filtra.

362 Hrvatski

7 Brisanjem osušite očišćeni spremnik za prašinu i relevantne dijelove.

2 Za pristup valjkastoj četki pronadite gumb na bočnoj strani nastavka. Pritisnite ga i zakrenite da biste ga otvorili.

4 Pažljivo uklonite zapetljanu kosu s valjkaste četke. Olakšajte si uklanjanje prljavštine škarama.

2 Rukom ili pomoću škara uklonite prljavštinu s četke.

Temperatura je preniska. Ako ikona baterije i ikona pogreške

istovremeno trepere u crvenoj boji, to znači da je temperatura okoline preniska ili previsoka.

Pobrinite se da temperatura u prostoriji u kojoj se uredaj upotrebljava, pohranjuje ili puni bude iznad 5 °C.

Introduzione

408 Italiano

levads

1 Nospiediet pogu roktura sānos.
2 Turot pogu nospiestu, izbīdiet barošanas bloku no rokas ierīces.

3 levietojiet caurules otru galu LED sprauslā (atskan klikškis).

4 Izlejiet üdeni no netirā üdens tvertnes izlietnē.

5 Uzlieciet mitro filtru atpakal netirā ūdens tvertnei.

11 levietojiet ierice tirā udens tvertni.

446 Latviešu

20 Laujiet mitrajam filtram nožut.

21 Uzlieciet mitro filtru atpakal netirā ūdens tvertnei.

2 Iznemiet mazgājamo putu filtru no plastmasas filtra korpusa.

454 Latviešu

3 Pasitiet pa atkritumu tvertni gan ar filtra korpusu, gan ar putu filtru.

2 Lai piekjutu rullisu sukai, atrodiet pogu uzgaja sānos. Nospiediet to un pagrieziet, lai atbrivotu suku.

Ivadas

3 Istatykite vamzdji antgalj su šviesos diodais.

2 Atidarykite dangtelj ant švaraus vandens bakelio.

5 Uždarykite vandens bakelio sandarinimo dangtelj.

480 Lietuviškai

10 Uždarykite vandens bakelj sandarinimo dangteliu.

Tik siurblio sąrankos valymas

Bevezetés

546 Magyar

Inleiding

1 Draai de borstel linksom om hem los te maken. Trek de borstel eruit zodra de vergrendeling los is.

610 Norsk

Innledning

3 Legg til 15 ml XV1792 Philips gulvrens til rentvannsbeholderen.

6 Sett rentvannsbeholderen tilbake i apparatet.

3 Sett den andre enden av røret inn i LED-munnstykket (klikk).

5 Bruk turboknappen för å bytte til en høyere oppsugingseffekt.

Tips: Det er også mulig å feste mini turbobørsten til slangen.

Advarsel: Ikke sug opp vann eller andre væsker.

Advarsel: Ikke sug opp vann eller andre væsker.

Advarsel: Ikke sug opp vann eller andre væsker.

4 Hell vannet ut av spillvannsbeholderen i vasken.

6 Sett den tomme spillvannsbeholderen tilbake i apparatet og ta ut rentvannsbeholderen.

630 Norsk

7 Fjern hetten fra rentvannsbeholderen.

8 Hell ut resterende flytende vaskemiddel fra rentvannsbeholderen i vasken.

11 Sett rentvannsbeholderen tilbake i apparatet.

17 Hell vannet ut av spillvannsbeholderen i vasken.

22 Sett spillvannsbeholderen tilbake i apparatet.

1 Slå av apparatet.

2 Ta det vaskbare skumfilteret ut av filterhuset i plast.

3 Bank ut filterhuset og skumfilteret over en søppelbøtte.

5 La det vaskede skumfilteret få tørke i 24 timer før du setter det tilbake på plass i filterhuset.

640 Norsk

6 Fest børsterullen på munnstykket – det høres en "KLIKK"-lyd när den går i inngrep.

656 Polski

Wprowadzenie