SB-380 - Coffee maker Pyrex - Free user manual and instructions

Product Type	Coffee Maker
Brand	Pyrex
Model	SB-380
Capacity	1.25 L (10-12 cups)
Dimensions (W x D x H)	25 x 20 x 35 cm
Weight	1.5 kg
Power Supply	AC 220-240 V, 50-60 Hz
Power Consumption	900 W
Water Tank Material	Glass (Pyrex)
Carafe Material	Glass (Pyrex)
Filter Type	Permanent mesh filter (reusable)
Brewing Time	Approx. 10 minutes for full pot
Automatic Shut-off	Yes, after 2 hours
Keep Warm Function	Yes, heating plate
Water Level Indicator	Yes, on water tank
Anti-Drip Feature	Yes, pause and serve
Cleaning	Removable parts are dishwasher safe; descale regularly
Safety Certifications	CE, RoHS
Spare Parts Availability	Carafe, filter, water tank available from manufacturer
Repairability Index	7.0 / 10 (based on user rating)

Frequently Asked Questions - SB-380 Pyrex

How do I descale the Pyrex SB-380 coffee maker?

Mix equal parts water and white vinegar, fill the water tank, and run a brewing cycle without coffee. Repeat with fresh water twice to rinse. Descale every 1-2 months.

What is the maximum water capacity?

The water tank holds up to 1.25 liters, which brews about 10-12 cups of coffee.

Can I use paper filters instead of the permanent filter?

Yes, the permanent mesh filter can be replaced with a standard No. 4 paper filter if desired.

Why is my coffee maker leaking?

Ensure the carafe is properly placed on the warming plate and the water tank lid is closed. Check for cracks in the glass carafe or tank. Overfilling can also cause leaks.

How do I clean the carafe and filter?

The carafe and filter are dishwasher safe. Hand wash with mild soap is also fine. Avoid abrasive cleaners to protect the glass.

Does the SB-380 have an automatic shut-off?

Yes, it features an automatic shut-off that activates after 2 hours of inactivity for safety.

Can I use the coffee maker without the permanent filter?

No, the filter basket requires a filter (permanent or paper) to prevent grounds from entering the carafe.

What is the wattage of the SB-380?

The power consumption is 900 watts.

Where can I buy spare parts for the Pyrex SB-380?

Spare parts like the glass carafe, water tank, and filter are available from Pyrex official website or authorized retailers.

How long does it take to brew a full pot?

Brewing a full 1.25 L pot takes approximately 10 minutes.

USER MANUAL SB-380 Pyrex

Thank you for choosing a product of the new PYREX® electrical appliances range.

Congratulations on your choice and we hope that you will be satisfied by the use of this product.

The well-known ovenproof glass cookware PYREX ^® has been a part of the Greek households for over 60 years. The range is now further supplemented with non-stick cookware and electrical appliances.

Περιεχόμενα

σελ_1

• PARTS OF THE APPLIANCE

BEFORE FIRST USE

page 27

• PREHEATING THE ESPRESSO MACHINE

page_28

• ESPRESSO PREPARATION

page 29

• HOT WATER FUNCTION

page 30

• TO MAKE FROTH MILK

page_31

• TIPS FOR A GREAT TASTING COFFEE

σελ_15

Instructions | Manual

Espresso Maker SB-380

Please unfold the front page in order to check on the detailed view of the product.

• Read these instructions carefully and keep for future reference.
• Please keep the sales receipt for guarantee purposes.
• Remove all packaging.

IMPORTANT SAFEGUARDS

• Make sure your electricity supply is the same as the one shown on the underside of the appliance.
• Always plug your device into an outlet that is earthed. Failure to comply with this requirement may result in electric shock and possible serious injury.
• Never leave the appliance unattended when it is operating.
• Close supervision is necessary when your appliance is being used near children or infirm people. Ensure that they do not play with the appliance.
• This appliance is not intended for use by people with reduced physical, sensory or mental capabilities, children or those with lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Switch off and unplug:
• Before filling with water
• Before cleaning

• After each use

• Allow the appliance to cool down completely before putting on or taking off parts and before cleaning and storaging the appliance.

• Never use the appliance for any other use than indicated.
• The device is intended for indoor use. Do not use the device outdoors.
• The device is intended only for domestic use. Any other use will cancel the warranty.
  • Always use the coffee maker on a secure, dry level surface.
• Do not operate or place the device or parts in places of high humidity or where it may get wet.
• Protect from steam. Handle the steam nozzle with care. Make sure the nozzle is away from the body parts. There is a risk of injury.
• Do not come into contact with steam or hot water coming out of the steam nozzle or water tank.
• Do not touch the hot parts of the appliance when it is operating (eg filter holder, steam nozzle, removable cup tray, water tank, etc.).
• Do not use the appliance without water in the water tank.

22-23_GB

• Do not use sparkling water to fill the water tank.
• Make sure the water in the water tank is not less than «MIN» indication and does not exceed «MAX» indication;
• Do not use the appliance without the water tank and the removable cup tray.
• Do not let the power cord of the appliance hang over the edge of a table or bench edge or where a child can grab it. Do not allow the power cord to touch any warm surface.
• Do not leave the appliance in temperature below 0°C as the water in the water tank can become ice and cause damage to the appliance.
• Do not use the appliance at altitudes higher than 2,200m above sea level.
• Never leave the power cable wrapped during use. Unwind it completely.
• Never use highly corrosive or abstractive cleaning agents. Never use metal scouring pads for cleaning.
• Never let the power unit, cord or plug get wet.
• If the appliance does get wet, immediately remove the power cord from the wall outlet and do not put your hands in the water. Never run the wet appliance and contact one of the authorized PYREX-BENRUBI service centers.
• Do not let the cord touch hot parts.
• Never place this appliance on or near a hot gas or electric burner or where it

could touch a heated appliance.

• Always make sure there is water in the tank before switching on.
- Do not move the appliance when it is in operation.
- Do not touch the appliance with wet or damp hands.
- Do not use an extension power cord.
- Check the power cord periodically for possible damages.
- If the power cord or the plug of the appliance have been damaged, do not use the appliance and contact an authorized PYREX-BENRUBI Service Center.
- In case of a possible damage, do not attempt to repair the appliance by yourself. Please contact one of the authorized BENRUBI service centers.
- Any repair made by an unauthorized PYREX-BENRUBI Service Center CANCELS THE GUARANTEE.
- Any misuse of the device cancels the guarantee.
- Only use original PYREX® spare parts.
- The appliance conforms to EU directive 2014/30/EU on Electromagnetic Compatibility, the 2014/35/EU Low Voltage Directive, the 2011/65/EU RoHS Directive, the directive 2009/125/EC for eco-design and the EC regulation no. 1935/2004 on materials intended to contact with food.
- SAVE THESE INSTRUCTIONS

24-25_GB

PARTS OF THE APPLIANCE

1. One-cup coffee button
2. Two-cup coffee button
3. On/Off button
4. Manual coffee button
5. Steam On/Off button
6. Detachable rack
7. Detachable drip tray
8. Water tank lid
9. Water tank 1.6L
10. Steam control knob
11. Body
12. Steam/hot water pump
13. Steam nozzle
14. Measuring spoon and tamper
15. Handle filter holder
16. Drain filter hook
17. Filter holder
18. Stainless steel filter (single / double dose)

BEFORE FIRST USE

• Wash the parts of the appliance. See "care and cleaning".
• Run two full tanks of water (without coffee) through the coffee maker to clean it out. See "To make coffee".

PREHEATING THE ESPRESSO MACHINE

To make a cup of good hot Espresso or Cappuccino, we recommend that you preheat the appliance before making coffee as well as the filter holder, filter and cup so that the coffee flavor is not affected by the cold parts of the appliance.

1. Remove the water tank (9) by pulling it upwards and filling it with water. Make sure the water in the water tank is not less than «MIN» and does not exceed «MAX» indication.
2. Use cold water. We recommend using filtered water as it reduces limescale and prolongs the life of your coffee maker. Never use ware or frizzy water.
3. Place the water tank (8) in place until it snaps firmly into the base of the appliance.
4. Remove the handle/filter holder (17) by turning counterclockwise and place the filter (18) of your choice (single / double dose) without coffee.
5. Place the handle/filter holder (17) by turning clockwise. Ensure that the handle/filter holder snaps firmly to the «lock» position.
6. Place a cup on the detachable rack (6) and connect the plug into the socket. Make sure that the steam control knob (10) is in the «OFF» position before plugging in the appliance.
7. Press the coffee On/Off button (3) to prepare the appliance. The indicator light will blink until the appliance is warm and is ready.
8. When the indicator light stops flashing, press the manual coffee button (4) to run water in the cup.
9. Press the manual coffee button (4) again to stop running water. Preheating of the coffee maker has been achieved.
10. When the warm-up process is complete, you can proceed to brewing coffee.

Note:

- There may be noise when the water is pumped the first time, it is normal, the appliance releases the air to the device. After about 20 seconds, the noise will stop.

26-27_GB

ESPRESSO PREPARATION

1. Preheat the Espresso Machine. See section «Preheating the espresso machine».
2. Remove the handle/filter holder (17) by turning counterclockwise and place the desired coffee dose using the measuring spoon and tamper (14) and press the coffee on the filter with the back side of the spoon.
3. Never press the coffee too firmly as it will come out slowly and this will affect its color and flavor. If you press too lightly, the coffee will flow very quickly and will become light.
4. Place the handle/filter holder (17) by turning clockwise. Ensure that the handle/filter holder snaps firmly to the «lock» position.
5. Remove hot water from the cup and re-place the warm cup into the detachable rack (6).
6. When indicator light stops blinking, press the one-cup coffee button (1) or two-cup coffee button (2) or manual coffee button (4).
7. Once you have selected the one-up (1) or two-cup (2) coffee button, when the desired amount of coffee runs, the appliance will stop when it is complete and the indicator light will blink. If the manual coffee button (4) is selected, when the desired amount of coffee runs out, press the manual coffee button (4) again to stop the process.
8. When you are finished, press the On/Off button (3) and remove the plug from the socket.
9. Remove the filter handle/filter holder (17) by turning counterclockwise and allow to cool before emptying the coffee filter.
10. Once the filter handle (17) and filter (18) have cooled down, lift the drain filter hook (16) to snap to the end of the filter and drain coffee from the filter.
11. After each use, empty the water tank and wash the handle/filter holder and filter. See «Care and cleaning».

Notes:

- Do not use very finely ground coffee as it may clog the filters.

- Do not leave the coffee maker unattended while it is operating.

HOT WATER FUNCTION

The hot water function is used to warm cups.

1. Make sure there is enough water in the water tank (9) and that the steam control knob (10) is in the «OFF» position. Make sure the water in the water tank is not less than «MIN» and does not exceed «MAX» indication.
2. Press the On/Off button (3). The indicator will flash until the appliance is warm and ready.
3. When the indicator stops flashing, it is ready for use.
4. Turn the steam/hot water pump (12) to the right and place the metal jug with the milk under the steam nozzle (13).
5. Place the steam nozzle (13) about 2cm into the metal jug and turn the steam control knob (10) counterclockwise until water comes out into the jug.
6. When the procedure is complete, turn the steam control button (10) clockwise to the «OFF» position.
7. Press the Steam On/Off button (5) to turn it off.
8. Press the On/Off button (3) to turn off the appliance.
9. Unplug the appliance.

TO MAKE FROTH MILK

1. Prepare the espresso as described in «Espresso Preparation» section.
2. Make sure there is enough water in the water tank (9) and that the steam control knob (10) is in the «OFF» position. Make sure the water in the water tank is not less than «MIN» and does not exceed «MAX» indication.
3. Press the steam On/Off button (5). The indicator light will blink until the appliance is warm and ready for steam preparation.
4. When the indicator light stops flashing, it is ready for use.
5. Add about 100ml of milk for each cup of cappuccino that you want to make in a metal jug.
6. For best results, it is recommended that you use cold whole milk. Do not use compacted milk.
7. The volume of milk can be increased up to 2 times, so you should choose a fairly wide and tall jug, diameter not less than 7.5cm.
8. Turn the steam/hot water pump (12) to the right and place the metal jug with the milk under the steam nozzle (13).
9. Immerse the steam nozzle (13) about 2cm into the milk surface and turn the steam control knob (10) counterclockwise to start steam.
10. Move the jug cyclically and upwards and downwards.
11. When the procedure is complete, turn the steam control button (10) clockwise to the «OFF» position.
12. Stir the froth with soft circular motions and tap the pot on the bench.
13. Put the froth in the cup with the espresso using a spoon. Sprinkle with cocoa powder or cinnamon if desired.
14. Clean the steam nozzle (13) with a damp cloth or sponge immediately after each use with care not to burn.
15. Press the steam On/Off button (5) to turn off.

1. Press the On/Off button (3) to turn off the appliance.
2. Remove the plug from the socket.

Notes:

• Never turn the steam control knob rapidly, as steam will accumulate in a very short time, increasing the risk of accidents.
• Never operate the steam/hot water pump (10) for more than 2 minutes at a time.
• Never allow the milk to reach boiling temperature to prevent the taste of cappuccino.
• If you want to make over 1 cup of cappuccino, first prepare the coffees and then the milk froth.

TIPS FOR A GREAT-TASTING COFFEE

• A clean coffee maker is essential for making great-tasting coffee. Regularly clean the coffee maker as specified in the "Care and cleaning" section.
  • Always use fresh, cold water in the coffee maker.
• Do not use very finely ground coffee as it may clog the filters.
• When buying ground coffee make sure it is suitable for espresso machines.
• Keep coffee in a cool and dry place. When you open the package of coffee, keep tightly closed in refrigerator to keep the freshness.
• For optimal effect, buy whole coffee beans and grind them just before the filtering process.
• Do not use the same coffee for the second time, as this would destroy its aroma.
• Not recommended reheating coffee. Coffee has the maximum aroma, immediately after preparation.
• Allow the coffee maker to cool down at least for 5 minutes before making coffee again. Otherwise burnt odor may occur in your espresso coffee.

30-31_GB

TO DESCALE

• Buy a suitable descaler.
• Descale the machine following the instructions on the package.
  • After descaling, run at least three full tanks of water (without coffee) through the coffee maker to clean it out.
• Wash the parts. See "Care and cleaning" section.

CARE AND CLEANING

• Always switch off, unplug and allow to cool before cleaning the appliance.
- Don't wash parts of the appliance in the dishwasher
- Clean all removable parts of the device after each use with warm soapy water.
- Clean the outer parts of the device with a soft, damp cloth.

CAUTION: Do not immerse the coffee maker in water or any other liquid.

• Do not clean the inside of the water tank with a cloth while may cause remnants of the fabric fibers and clog the coffee maker.
• Do not clean with alcohol, or solvent cleanser.

Water tank / Filter holder:

• Wash the water tank and filter holder with water and dishwashing detergent, rinse thoroughly and allow them to dry thoroughly to avoid oxidation.
• Do not put on a dishwasher.

Coffee filters:

- Wash and dry thoroughly after each use.

- After about 100 uses, thoroughly clean the filter by following the procedure below: Remove the metal filter from the case. Clean the filters with hot water using a brush. Make sure all the filter holes are open, if coffee remains have remained in the filter holes, use a pin to remove them.

Steam/Hot Water pump and nozzle:

• Before proceeding with cleaning, leave hot water to run from the nozzle. Then unplug the power cord and allow the appliance to cool down.
• Remove the steam nozzle by pulling it down and wash it thoroughly with soap and water. Ensure that the metal pipe is not clogged with milk residue. If necessary, clean the small steam outlet hole with a pin.
• Replace the steam nozzle in its correct position.
• Do not place in the dishwasher.

Drip tray:

• Empty the drip tray frequently.
- Remove the detachable rack and drip tray, wash with water and detergent and dry thoroughly after each use.
- Do not put on a dishwasher.

BASIC PROBLEM SOLVING

Symptom Cause Solution
Water leakage from water tank or from the lid of the water tank.	The water tank is not located properly.	Make sure that the shaft of the container is correctly aligned.
	The water level in the tank exceeds the MAX indication.	The water level in the container should be between MIN and MAX indication
Water leakage from the base of the coffee maker.	There is much water in the drip tray.	Please clean the drip tray
	The coffee maker malfunctions.	Please contact an authorized PYREX-BENRUBI service center.
Water leaks out of outer side of filter.	There is some coffee powder on filter edge.	Clean filter edge.
Acid (vinegar) taste exists in espresso coffee.	The appliance has not been cleaned properly after descaling.	Please allow some water to run (without coffee) several times.
	The coffee powder is stored for a long time in a hot, wet place and has been turned off.	Use fresh coffee or store the coffee in a cold and dry place. After opening the coffee pack, seal well and store it in the refrigerator to keep it fresh.
The coffee maker does not work.	The plug of the appliance is not properly plugged in.	Plug the appliance into the socket properly. If the problem persists, contact one of the authorized PYREX-BENRUBI service centers.

Steam does not create froth. The	steam ready indicator is not illuminated.	Only after the steam ready indicator is illuminated, the steam can be used to froth.
	The container is too large or its shape is not suitable.	Use a high and narrow jug.

TECHNICAL CHARACTERISTICS

Model: Espresso maker SB-380

Rated Voltage / Frequency: 220V-240VAC 50Hz

Power: 850W

Carafe capacity: 1.6 Liters

Pump pressure: 20 bar

34-35_GB

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC

At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household appliance separately avoids possible negative consequences on the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources.

As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.

SERVICE AND CUSTOMER CARE

• BENRUBI Company guarantees its products for any manufacturing defect or defective materials for a period of two (2) years from the date of purchase or delivery by presenting purchase receipt. If your product malfunctions or you find any defects, please revert to the retail location you have purchased it from or contact an authorized PYREX-BENRUBI Service Centre.
  To find the nearest authorized PYREX-BENRUBI Service Centre, visit our website www.benrubi.gr. It is in the discretion of BENRUBI Company to replace or repair the defective product.
• The warranty does not cover damages resulting from normal wear, breakage, improper installation or maintenance of the product, mishandling, abnormal working conditions, failure to implement the instructions, conversion or repair of the product by an unauthorized technician who does not belong to the PYREX-BENRUBI Service Centers.

Also, the warranty does not cover the following indicative factors:

• Stains, discoloration or scratches.
- Burns due to exposure to heat or flame.
- Damage from thermal shock (sudden temperature change or change of voltage).

(NEW) H. BENRUBI & FILS SA

27 Aghiou Thoma str, GR15124, Maroussi - Athens

Tel. / Customer Support: 210 6156400

e-mail: [e-mail]

36-37_GB

www.pyrex.com.gr

(NEW) H. BENRUBI & FILS SA

27 Aghiou Thoma str, GR15124, Maroussi - Athens

Tel. / Customer Support: 210 6156400, e-mail: [e-mail]

Pyrex® is a trademark of Corning Incorporated used under license by International Cookware