MicroTubes 500v2 - Guitar amplifier Darkglass - Free user manual and instructions
Find the device manual for free MicroTubes 500v2 Darkglass in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Bass Amplifier Head |
| Power Output | 500W RMS @ 4 ohms |
| Dimensions (H x W x D) | 169 x 273 x 137 mm |
| Weight | 2.3 kg |
| Input Impedance | 1 MΩ |
| Frequency Response | 10 Hz – 20 kHz |
| Power Supply | AC 100-240V, 50/60Hz |
| EQ Section | 4-band: Low, Low-Mid, Hi-Mid, Treble |
| Distortion Engine | MicroTubes overdrive with active/passive switches |
| Compressor | Built-in compressor with threshold control |
| Speaker Outputs | 1x Speakon (4 ohms minimum) |
| Line Output | XLR balanced with pre/post EQ switch |
| Headphone Output | 3.5mm stereo jack |
| Aux Input | 3.5mm stereo jack for backing tracks |
| Footswitch Control | Compatible with Darkglass FS1 footswitch (distortion bypass) |
| Construction | Aluminum chassis with steel bottom plate |
| Cooling | Fan-cooled for efficient heat dissipation |
| Maintenance | Clean with dry cloth; avoid solvents and liquids |
| Safety | Ensure proper ventilation; do not block vents |
| Spare Parts & Repairability | Contact Darkglass support for authorized service |
| Additional Information | Designed in Finland |
Frequently Asked Questions - MicroTubes 500v2 Darkglass
How do I connect the MicroTubes 500v2 to a speaker cabinet?
Use a Speakon cable to connect the amplifier's Speaker Output to your cabinet. Ensure the cabinet impedance is at least 4 ohms.
Can I use the MicroTubes 500v2 as a preamp for recording?
Yes, use the balanced XLR Line Output. Set the pre/post switch to 'Post' to include EQ and effects in the signal.
What is the power consumption of this amplifier?
The MicroTubes 500v2 consumes up to 600W under full load. It automatically switches between 100-240V AC.
How do I engage the MicroTubes distortion?
Press the footswitch (if connected) or the front panel Distortion switch. Adjust the Drive and Tone controls to shape the overdrive.
Is the headphone output stereo?
Yes, the 3.5mm headphone jack outputs a stereo signal. It mutes the speaker outputs automatically.
Can I use the aux input simultaneously with the instrument input?
Yes, the Aux Input is designed for backing tracks. It mixes with the instrument signal and is affected by volume controls.
What does the Active/Passive switch do?
It adjusts input sensitivity. Switch to Active for high-output basses, Passive for standard passive instruments. Typically set to 0 dB for active and -6 dB for passive.
How do I clean the amplifier?
Disconnect power. Wipe the exterior with a dry, lint-free cloth. Do not use water, solvents, or abrasive cleaners.
What is the minimum impedance for speaker cabinets?
The amplifier requires a minimum impedance of 4 ohms. Using a lower impedance may damage the output stage.
Why does the fan run continuously?
The fan is temperature-controlled. It may run at low speed even when idle. If it runs loud or stops, contact Darkglass support.
User questions about MicroTubes 500v2 Darkglass
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Guitar amplifier in PDF format for free! Find your manual MicroTubes 500v2 - Darkglass and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MicroTubes 500v2 by Darkglass.
USER MANUAL MicroTubes 500v2 Darkglass
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Darkglass
Model : MicroTubes 500v2
Category : Guitar amplifier