ACL LED Par 64 - Projector Ignition - Free user manual and instructions
Find the device manual for free ACL LED Par 64 Ignition in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Par Can |
| Model | ACL LED Par 64 |
| Brand | Ignition |
| Light Source | 64 x 5mm LEDs |
| Color Mixing | RGB (Red, Green, Blue) |
| Control Protocol | DMX512 |
| DMX Channels | 3, 4, or 7 selectable |
| Operating Modes | DMX, Standalone, Master/Slave, Sound Active |
| Beam Angle | 25 degrees |
| Power Consumption | 30W |
| Input Voltage | AC 100-240V, 50/60Hz |
| Dimensions (L x W x H) | 10.2 x 8.5 x 8.5 inches |
| Weight | 3.5 lbs |
| Cooling | Convection cooled |
| Housing Material | Aluminum die-cast |
| Mounting | Mounting bracket with safety cable loop |
| Cleaning | Wipe with a dry cloth; do not use solvents |
| Safety | Use safety cable; disconnect power before cleaning |
| Spare Parts | LED board, power supply, DMX input/output modules |
| Repairability | Modular design; replaceable LED boards |
| General Information | Compact LED par for stage and architectural lighting |
Frequently Asked Questions - ACL LED Par 64 Ignition
How do I connect the ACL LED Par 64 to a DMX controller?
Use a standard 3-pin XLR cable to connect the DMX input of the fixture to the DMX output of your controller. Set the DMX address using the DIP switches or menu on the rear panel. Ensure the controller is set to the same address range.
What is the maximum number of units I can daisy-chain?
You can daisy-chain up to 32 units on a single DMX line using the DMX in/out connectors. Use a DMX terminator (120 ohm resistor) on the last fixture to avoid signal reflections.
How to set the fixture to sound-active mode?
Press the menu button until you see Sound mode on the display. Use the up/down buttons to enable it. The light will react to ambient sound via the built-in microphone. You can adjust sensitivity from the menu.
Can I use this fixture without a DMX controller?
Yes, you can use it in standalone mode. Select a built-in program (auto or sound-active) from the menu. You can also synchronize multiple units in master/slave mode by connecting them with XLR cables and setting one as master.
What is the recommended cleaning procedure?
Disconnect the power and let the fixture cool. Use a soft, dry cloth to gently wipe the housing and lens. Do not use alcohol, solvents, or abrasive cleaners. Clean the ventilation grills regularly to prevent overheating.
How many DMX channels does the ACL LED Par 64 use?
It supports 3, 4, or 7 channels depending on the selected mode. 3-channel mode controls RGB; 4-channel adds a master dimmer; 7-channel adds strobe and macro effects. Set via the menu or DIP switches.
Can I replace the LEDs?
Yes, the LED board is replaceable. Contact the manufacturer or an authorized service center for spare parts. Disconnect power before opening the unit. Soldering may be required if replacing individual LEDs.
What is the beam angle and how does it affect the light spread?
The beam angle is 25 degrees, providing a narrow, intense beam suitable for highlighting objects or creating tight color washes. For wider coverage, you may need to place the fixture further away or use diffusion filters.
Why is the light not turning on?
Check the power connection and ensure the fixture is set to the correct input voltage (100-240V AC). Verify the power switch is on and the fuse (if any) is intact. If using DMX, ensure the controller is powered and the address is correct. Try resetting to factory defaults.
How to perform a factory reset?
Press and hold the menu button for about 5 seconds until the display shows Reset. Confirm by pressing enter. This restores all settings to factory defaults. After reset, you need to reconfigure DMX address and mode.
User questions about ACL LED Par 64 Ignition
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Projector in PDF format for free! Find your manual ACL LED Par 64 - Ignition and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ACL LED Par 64 by Ignition.
USER MANUAL ACL LED Par 64 Ignition
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Ignition
Model : ACL LED Par 64
Category : Projector