DSO-1204E - Uncategorized VOLTCRAFT - Free user manual and instructions
Find the device manual for free DSO-1204E VOLTCRAFT in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Digital Storage Oscilloscope |
| Model | DSO-1204E |
| Brand | Voltcraft |
| Bandwidth | 100 MHz |
| Number of Channels | 4 |
| Sample Rate | 1 GS/s (per channel) |
| Vertical Resolution | 8 bits |
| Record Length | 1 Mpts per channel |
| Display Size | 7-inch TFT LCD (800x480 pixels) |
| Dimensions (W x H x D) | 322 x 152 x 118 mm |
| Weight | 2.6 kg |
| Power Supply | 100-240 V AC, 50/60 Hz |
| Power Consumption | 30 W |
| Main Functions | Waveform acquisition, FFT analysis, automatic measurements, triggering |
| Connectivity | USB Host/Device, LAN, VGA output |
| Calibration | Self-calibration via firmware |
| Maintenance | Clean with a soft, dry cloth. Do not use solvents. |
| Safety Category | CAT I (for mains measurements, use included 10x probe rated CAT II 300V) |
| Included Accessories | 4 passive probes (100 MHz, 10x), power cord, USB cable, calibration certificate |
| Repair & Spare Parts | Contact Voltcraft service center for repair; spare probes available online |
Frequently Asked Questions - DSO-1204E VOLTCRAFT
How do I perform a self-calibration on the DSO-1204E?
Go to the Utility menu, select 'Self-Cal', and follow the on-screen instructions. Ensure all probes are disconnected.
This compensates for temperature drift and aging.
This compensates for temperature drift and aging.
What is the maximum input voltage for the probes?
The included 10x probes are rated for CAT II 300 V (DC + AC peak). With 1x mode, limit to 30 V RMS.
Always check the probe derating curve at high frequencies.
Always check the probe derating curve at high frequencies.
Can I measure AC mains voltage directly?
Yes, but use the 10x probe setting and ensure the oscilloscope is set to 10x in the channel menu.
Maximum safe measurement is 300 V CAT II.
Never use 1x mode for mains.
Maximum safe measurement is 300 V CAT II.
Never use 1x mode for mains.
How do I update the firmware?
Download the latest firmware from the Voltcraft website, copy it to a FAT32 USB drive, and insert it into the oscilloscope.
Go to Utility > Update Firmware. Do not power off during the process.
Go to Utility > Update Firmware. Do not power off during the process.
How can I take a screenshot of the waveform?
Press the 'Print' button on the front panel.
The image will be saved to a USB flash drive (inserted in the Host port) as a BMP file.
The image will be saved to a USB flash drive (inserted in the Host port) as a BMP file.
What is the resolution of the FFT function?
The FFT provides up to 1024 points with Hanning, Hamming, Blackman, and Rectangular window options.
It shows frequency components up to half the sample rate.
It shows frequency components up to half the sample rate.
How do I enable pass/fail testing?
Define a mask by capturing a reference waveform and adjusting the tolerance.
Then go to the 'Pass/Fail' menu, enable the test, and choose actions (stop, save, etc.).
The oscilloscope will compare incoming signals to the mask.
Then go to the 'Pass/Fail' menu, enable the test, and choose actions (stop, save, etc.).
The oscilloscope will compare incoming signals to the mask.
Why does my measurement show incorrect voltage?
Check the probe attenuation setting: ensure the channel menu Probe matches the physical probe switch (1x or 10x).
Also verify the vertical scale is appropriate for the signal.
Perform a self-calibration if needed.
Also verify the vertical scale is appropriate for the signal.
Perform a self-calibration if needed.
How do I connect the oscilloscope to a PC?
Use the USB Device port on the rear panel with the provided cable. Install the Voltcraft UltraScope software (available for download).
Then select 'USB' in the software's connection settings.
Then select 'USB' in the software's connection settings.
What should I do if the display is frozen?
First try pressing the 'Default Setup' button to restore factory settings.
If that fails, power cycle the oscilloscope: turn off, wait 10 seconds, and turn on.
If the issue persists, contact support.
If that fails, power cycle the oscilloscope: turn off, wait 10 seconds, and turn on.
If the issue persists, contact support.
User questions about DSO-1204E VOLTCRAFT
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual DSO-1204E - VOLTCRAFT and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DSO-1204E by VOLTCRAFT.
USER MANUAL DSO-1204E VOLTCRAFT
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : VOLTCRAFT
Model : DSO-1204E
Category : Uncategorized