MPG EZ120 ARGB - CPU Cooler MSI - Free user manual and instructions

Product Type	CPU Air Cooler with ARGB Lighting
Compatibility	Intel LGA 1700/1200/115X, AMD AM5/AM4
Fan Dimensions	120 x 120 x 25 mm
Heatsink Dimensions	120 x 80 x 155 mm (approximate)
Total Weight	~750 g (including fan)
Fan Speed	500 – 1800 RPM ± 10%
Airflow	Up to 60 CFM
Noise Level	18 – 30 dBA
Bearing Type	Hydraulic Bearing
Lighting	Addressable RGB (ARGB) – 3-pin 5V header compatible
Fan Connector	4-pin PWM
Power Consumption	2.4 W (fan) + 3.5 W (LEDs, max)
Electrical Rating	12 V DC, 0.2 A (fan), 0.7 A (LEDs)
Main Features	Dual-tower heatsink, direct contact heatpipes, pre-applied thermal paste, ARGB synchronization with MSI Mystic Light
Maintenance	Clean dust with compressed air or soft brush; avoid liquids
Safety	Do not operate with damaged cable; ensure proper mounting to prevent short circuit
Spare Parts	Replacement fan (12V ARGB), mounting kits for Intel/AMD, thermal paste
Repairability	Fan and heatsink are separable; fan can be replaced by standard 120 mm fan
Warranty	Typically 3 years (check local terms)

Frequently Asked Questions - MPG EZ120 ARGB MSI

What CPU sockets is the MPG EZ120 ARGB compatible with?

The cooler supports Intel LGA 1700/1200/115X and AMD AM5/AM4 sockets. Always check the included mounting kit for your specific socket.

Does the ARGB lighting require a separate controller?

The fan uses a standard 3-pin 5V ARGB header. You can connect it directly to your motherboard's ARGB header or to a compatible ARGB controller for synchronization.

How do I control the fan speed?

The fan is PWM-controlled via a 4-pin header. You can adjust speed in the motherboard BIOS or using software like MSI Center.

Can I use the cooler with a taller RAM kit?

The heatsink overhangs the RAM slots slightly. For most standard-height RAM, clearance is fine. However, very tall RAM with large heatspreaders may interfere; check the clearance of 45 mm from the motherboard.

Is thermal paste pre-applied?

Yes, the cooler comes with pre-applied thermal paste on the base. If you remove or reposition the cooler, you must clean and reapply new thermal paste.

How to clean the cooler?

Unplug the fan and use compressed air to blow away dust from the fins and fan blades. Use a soft brush for stubborn dirt. Avoid using water or cleaning solvents.

Can I replace the fan with a different one?

Yes, the fan is standard 120x25 mm and can be replaced. Ensure the replacement fan is PWM and matches the 4-pin header. The ARGB cable must be 3-pin 5V for lighting.

What software can I use to control RGB lighting?

You can use MSI Mystic Light (via MSI Center) or other motherboard RGB software that supports standard 5V ARGB. The lighting is addressable and can be customized.

What is the maximum TDP the cooler can handle?

The MPG EZ120 ARGB is designed for CPUs up to approximately 180W TDP, suitable for mid-range to high-end processors under typical loads.

Does the cooler include a mounting backplate?

Yes, the package includes a universal backplate for both Intel and AMD sockets. Installation steps are detailed in the manual.

USER MANUAL MPG EZ120 ARGB MSI

MPG Series

Fan

MPG EZ120 ARGB

MPG EZ120 ARGB WHITE

User Guide

Contents

Specifications....3

Package Contents - Three Fans ....4

Package Contents - Single Fan ....5

Safety Information....6

Installation - Three Fans....7

Daisy Chaining Fans....10

Hub Connection....11

Attaching the Hub with Magnet Plate ....12

Installation - Single Fan 13

JAF_2 Compatibility Information ....15

Mystic Light Usage Instructions ....16

Cooling Wizard Usage Instructions ....18

General Information ....19

Specifications

Dimensions (L x W x H) 120 x 120 x 28 mm / 4.7 x 4.7 x 1.1 inches
Exterior Color Black / White
Rated Voltage 12 V
Fan Speed 0 ~ 1900 ±10% RPM
Airflow 73.82 CFM
Air Pressure 2.56 mmH2O
Max. Noise Level 28.82 dBA
Bearing Type Fluid Dynamic Bearing
Connector Type 4 pin PWM + 3 pin ARGB / 7 pin JAF
Rating Voltage DC 12 V (fan) / 5 V (LED)
Rated Current 0.25 A Max.
Input Power 3 W Max.
Fan Weight 201g / pcs

Package Contents - Three Fans

Decorative Block No.2 x1

Decorative Block No.3 x1

Decorative Block No.4 x1

Magnetic Block No.5 x2

Magnetic Block No.6 x2

ARGB Fan Control Hub x1

Magnetic Plate x1

Screw #6-32 33mm x12 Screw M5 10mm x12

MicroUSB-JUSB Cable x1 Hub-Fan-ARGB Y Cable x1 Hub-JAF1 Cable x1 Fan-Hub Cable x4 Daisy Chain Cable x1

Package Contents - Single Fan

Decorative Block No.2 x1

Decorative Block No.3 x1

Decorative Block No.4 x1

Screw #6-32 33mm x4

Screw M5 10mm x4

Fan-JAF1 Cable x1, Fan-ARGB Cable x1

If any of the above items are damaged or missing, please contact your retailer.

Safety Information

• Always disconnect the fan from the power source before performing any maintenance or installation.
• Be cautious when handling the fan blades. They may have sharp edges that could cause injury. Handle with care, and avoid touching the blades when the fan is running.
• Always turn off the power supply and unplug the power cord from the power outlet before installing or removing.
• Do not boot the computer before installation is completed. This could cause permanent damage to the components as well as injury to the user.
• Before turning on the computer, ensure that there are no loose screws or metal components on the motherboard or anywhere within the computer case.
• Use the provided screws for installation. Do not use screws that are too long, as they could damage the fan or other components.
• Ensure that the fan is not obstructed by any objects that could impede airflow. Proper ventilation is essential for optimal cooling.
• Monitor your system’s temperatures to prevent overheating. If the fan fails or becomes noisy, replace it promptly to avoid damage to your components.

Installation - Three Fans

The steps to install three fans are as follows:

Please note that the illustrations below are for reference only. The placement may vary, depending on the case and actual parts you have.

1. Align the two protrusions on the side of one fan with the two recesses on the side of another fan, and connect the three fans together. The fans have magnets on the sides, and when the magnets are aligned correctly, the fans will snap together.

1. Connect three fans together using the Magnetic Block No.5 and Magnetic Block No.6. The blocks have shaped magnets, and if the magnets and shapes are aligned correctly, the blocks will snap into place with a click. If the magnets are misaligned, the blocks will pop off.

1. Install the Fan-Hub Cable. This cable also has magnets, and if the magnets are misaligned, the cable will pop off. If this happens, please try installing the cable on the other end of the fan.

1. Install the decorative blocks.

1. Screw the fans to the radiator or PC case, as shown in the figure below.

1. Refer to the Hub Connection section for guidance on connecting the Hub.

Daisy Chaining Fans

When you need to link separate fans, use the Daisy Chain Cable for daisy chaining. This approach enables you to link two sets of fans, as shown in the accompanying diagram. Daisy chaining simplifies wiring, enhances organization, and maintains both optimal performance and visual consistency in your system’s configuration.

Hub Connection

1. Attach the Hub's 4-Wire SATA Power Connector to the PSU's SATA port for power.
2. Connect the MicroUSB-JUSB Cable from the Hub to your motherboard's JUSB port.
3. For Motherboards with JAF_1: If you have a MEG Z790 GODLIKE MAX, MEG Z790 ACE MAX, MPG Z790 CARBON MAX WIFI, MPG Z790 EDGE TI MAX WIFI, or a newer MSI motherboard with a JAF_1 connector, use the Hub-JAF1 Cable to connect the Hub to the JAF_1 port on the motherboard. Please check the product page for more compatible motherboards.
4. For Motherboards without JAF_1: If there's no JAF_1 connector, use the Hub-Fan-ARGB Cable to connect the Hub to the JARGB and SYS_FAN connectors on the motherboard.
5. Connect the EZ120 fans to the hub using the Fan-Hub Cable.

• Fans connected to the hub must first be connected to port 1. - If you are connecting more than 12 fans, it is necessary to connect both the 4-Wire SATA Power Connector and the 2-Wire SATA Power Connector to ensure adequate power supply.

Attaching the Hub with Magnet Plate

To secure the Hub inside your PC case, first peel off the protective layer from one side of the Magnetic Plate. Then, firmly attach this adhesive side to the back of the Hub. This enables the Hub to magnetically adhere to the metal frame of the computer case, ensuring a stable and convenient placement.

Installation - Single Fan

The steps to install single fan are as follows:

1. For Motherboards with JAF_1: If you have a MEG Z790 GODLIKE MAX, MEG Z790 ACE MAX, MPG Z790 CARBON MAX WIFI, MPG Z790 EDGE TI MAX WIFI, or a newer MSI motherboard with a JAF_1 port, use the JAF_1 Cable to connect the EZ120 fan to the JAF_1 connector on the motherboard. Please check the product page for more compatible motherboards.
2. For Motherboards without JAF_1: If there's no JAF_1 connector, use the Fan-ARGB Cable to connect the EZ120 fan to the JARGB and SYS_FAN connectors on the motherboard.
3. Install the decorative blocks.

1. Connect the EZ120 fan to the motherboard.

JAF_2 Compatibility Information

MSI's latest motherboards have upgraded to the JAF_2 connector, which includes additional pins designed to maintain backward compatibility with the JAF_1 configuration. When using the JAF_2 connector, pins 1 to 7 carry the same signals as JAF_1, ensuring full compatibility with components designed for JAF_1. This means the MPG EZ120 ARGB fan can be directly connected to the JAF_2 connector without any issues.

Pins 1 to 7 of JAF_2 are compatible with JAF_1.

For detailed guidance on using MSI's exclusive EZ Conn connector and cable, please click the following link or scan the QR code:

How to use MSI exclusive EZ Conn-connector and cable

Mystic Light Usage Instructions

Mystic Light is a feature within the MSI Center designed to enhance your system's aesthetics through customizable lighting. For detailed instructions on installation and usage, please refer to http://download.msi.com/manual/mb/MSICENTER.pdf or scan the QR code to access.

1. After installing the MSI Center, launch the application, navigate to the Features section, and select the Mystic Light to begin customizing your system's lighting.
2. In the Mystic Light interface, you will see a list of connected devices. Click on the HUB icon to access your device settings.

1. For first-time setup, follow the prompts to configure the ARGB control and fan quantity.

Note: Initially, 4 ports are activated by default, with each port accommodating up to 3 fans. The software supports controlling a maximum of 18 fans across these ports.

Turn each port on or off

1. Select the Port to which your fans are connected to configure their lighting settings.

Choose lighting effects for your device

Important

- MPG EZ120 ARGB custom setting requires its fan hub of 3-fan pack.

- MPG EZ120 ARGB fans are synchronized with motherboard setting without the fan hub.

LED Mode: Each fan can be controlled individually within 3 distinct zones.

Color Setting: Choose your preferred color for the lighting effect.

Brightness: Adjust the light intensity of the fans to your liking.

Light Speed: Select the speed at which the lighting effect operates.

A. You have several lighting effects to choose from for your device. To individually adjust the fan lighting within each port, please select the Customize. B. Use the Select Tool to select individual LED areas on each fan. You can group multiple LED areas by holding the Ctrl key and clicking to select. The Magic Select Tool allows you to select a single area and automatically includes other areas that are part of the group.

Select Tool: select areas. Hold Ctrl and click to group areas.

Magic Select Tool: select one to include grouped areas.

The black rectangle indicates the selected areas.

1. Once you have chosen your settings, click Apply to update the lighting effects on your device.

Cooling Wizard Usage Instructions

Please refer to the Cooling Wizard section in the MSI Center manual for installation and setup instructions.

http://download.msi.com/manual/mb/MSICENTER.pdf

or scan the QR code to access.

Here are the steps to access the Cooling Wizard:

1. After installing MSI Center and Cooling Wizard, go to Features > Cooling Wizard.
2. Locate the configuration area for MPG EZ120 ARGB.

MPG EZ120 ARGB fan speed settings

1. Follow the instructions in the MSI Center manual for more settings.

General Information

KC Certification

R-R-MSI-MS-7G24

Company: MSI Korea Co., Ltd.

Product name: Fan Hub

Model name: MS-7G24

Manufacturing date: 2024

Manufacturer and country of manufacture: MSI/China

Copyright and Trademarks Notice

Copyright © Micro-Star Int’l Co., Ltd. All rights reserved.

The MSI logo used is a registered trademark of Micro-Star Int'l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.

All text, images, illustrations, and other content in this manual are the property of MSI. No part of this manual may be reproduced, distributed, or used in any form without the written permission of MSI.

Revision History

• Version 1.0, 2024/03, First release. • Version 1.1, 2024/05, Add KCC. • Version 1.4, 2024/11, Add JAF_2.