TTA-500 - Uncategorized Taga Harmony - Free user manual and instructions
Find the device manual for free TTA-500 Taga Harmony in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Integrated Stereo Amplifier |
| Brand | Taga Harmony |
| Model | TTA-500 |
| Dimensions (W x H x D) | 430 x 120 x 350 mm |
| Weight | 8 kg |
| Power Supply | AC 230V, 50Hz |
| Output Power | 2 x 100W (8 ohms) |
| Frequency Response | 20 Hz - 20 kHz |
| Total Harmonic Distortion | < 0.05% |
| Inputs | 4x RCA, 1x Phono (MM), 1x AUX |
| Outputs | Speaker terminals (A/B), 1x Subwoofer out, 1x Record out |
| Headphone Output | 3.5mm on front panel |
| Remote Control | Included (infrared) |
| Protection Circuit | Overload, short circuit, thermal |
| Impedance Compatibility | 4-16 ohms |
| Signal-to-Noise Ratio | > 90 dB |
| Chassis Material | Aluminum front panel, steel body |
| Maintenance & Cleaning | Wipe with soft, dry cloth. Avoid liquids and aerosols. |
| Safety Instructions | Do not open the device. Keep away from moisture and heat sources. |
| Spare Parts & Repairability | Contact authorized service center. Some parts available via Taga Harmony support. |
Frequently Asked Questions - TTA-500 Taga Harmony
How do I connect my speakers to the TTA-500?
Use speaker cables. Connect the stripped ends to the speaker terminals on the rear panel. Ensure correct polarity (red to red, black to black). The amplifier supports A and B speaker sets; press the corresponding buttons on the front panel to activate.
Can I use the TTA-500 with a turntable?
Yes. The TTA-500 has a dedicated Phono input for moving magnet (MM) cartridges. Connect your turntable's RCA cables to the Phono input and ground wire to the GND terminal. Do not use a separate phono preamp.
What is the maximum power output of the TTA-500?
The TTA-500 delivers 2 x 100W into 8 ohms and 2 x 150W into 4 ohms. Ensure your speakers have a suitable power handling capacity.
How do I use the remote control?
Insert two AAA batteries (not included) into the remote. Point it at the IR sensor on the front panel. The remote controls volume, input selection, mute, and standby.
The amplifier does not turn on. What should I check?
First, check that the power cord is securely connected and the wall outlet is working. Ensure the main power switch on the rear is on. If the amplifier goes into protection mode, turn it off, wait a few minutes, and try again. Check speaker connections for short circuits.
Can I connect a subwoofer to the TTA-500?
Yes. Use the Subwoofer out RCA output on the rear. Connect it to your powered subwoofer's input. You can adjust the subwoofer volume via the subwoofer itself.
What is the correct way to clean the TTA-500?
Unplug the unit. Use a soft, dry microfiber cloth to wipe the exterior. Do not use any liquids, solvents, or abrasive cleaners. For ventilation grilles, gently use a soft brush.
Is there a headphone output on the TTA-500?
Yes. There is a 3.5mm headphone jack on the front panel. When headphones are plugged in, the speaker outputs are automatically muted.
How do I reset the TTA-500 to factory settings?
There is no user-accessible factory reset. If you experience persistent issues, unplug the unit for at least 10 minutes. If problems continue, contact Taga Harmony support.
Where can I find the user manual for the TTA-500?
The user manual is available for free download on notice-facile.com. Go to the TTA-500 page and click the 'Download' button to get the PDF. Alternatively, you can request a translated version by selecting your language and providing your email.
User questions about TTA-500 Taga Harmony
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual TTA-500 - Taga Harmony and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TTA-500 by Taga Harmony.