M4300-8X8F - Computer Accessories NETGEAR - Free user manual and instructions
Find the device manual for free M4300-8X8F NETGEAR in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Managed Switch |
| Number of Ports | 16 (8 x 10G SFP+, 8 x 1G RJ-45) |
| Form Factor | 1U Rackmount |
| Dimensions (W x D x H) | 440 mm x 324 mm x 43 mm |
| Weight | 4.5 kg |
| Power Supply | Internal 100-240VAC, 50-60Hz |
| Power Consumption | Max 60W |
| Operating Temperature | 0°C to 50°C |
| Humidity | 5% to 95% non-condensing |
| Management | Web GUI, CLI, SNMP, RMON |
| Advanced Features | VLAN, QoS, Link Aggregation, ACL, STP/RSTP/MSTP, IGMP Snooping |
| Stacking | Yes (up to 8 units) |
| Warranty | Limited Lifetime |
| Cooling | Fan with variable speed |
| LED Indicators | Power, per-port link/activity, stacking |
Frequently Asked Questions - M4300-8X8F NETGEAR
How do I reset the M4300-8X8F to factory defaults?
Press and hold the Factory Defaults button on the front panel (using a paperclip) for 5 seconds until the LEDs flash. The switch will reboot with factory settings.
What is the default IP address to access the web interface?
The default IP address is 192.168.0.239. Ensure your computer is on the same subnet (e.g., 192.168.0.x) and connect via an Ethernet cable.
Does this switch support PoE?
No, the M4300-8X8F does not provide PoE (Power over Ethernet). It is a pure data switch with copper and fiber ports.
How can I configure VLANs on the M4300-8X8F?
Access the web GUI, go to Switching > VLAN > Basic. You can create 802.1Q VLANs, assign ports, and set port VLAN mode (Access or Trunk).
What is the maximum number of VLANs supported?
This switch supports up to 1024 VLANs (VLAN ID range 1-4094).
How do I update the firmware?
Download the latest firmware from Netgear support. In the web GUI, go to Maintenance > File Management, upload the firmware file, and apply. The switch will reboot.
Can I stack multiple M4300 units?
Yes, up to 8 units can be stacked using dedicated stacking ports (on the rear). Stacking allows management as a single logical switch.
What SFP+ modules are compatible?
Use Netgear AXM761 (10GBASE-SR) or AXM762 (10GBASE-LR) or any MSA-compliant SFP+ module. Third-party modules may work but are not officially supported.
How do I enable Link Aggregation (LAG)?
In the web GUI, go to Switching > LAG. Create a new LAG, assign member ports, and configure LACP (active/passive) as needed.
What should I do if the switch is not booting?
Check the power cord and LED. If no LED, try a different outlet. If the switch powers on but stuck, perform a factory reset or contact Netgear support.
User questions about M4300-8X8F NETGEAR
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Computer Accessories in PDF format for free! Find your manual M4300-8X8F - NETGEAR and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. M4300-8X8F by NETGEAR.
USER MANUAL M4300-8X8F NETGEAR
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : NETGEAR
Model : M4300-8X8F
Category : Computer Accessories