RB38C7B5C22 - Refrigerator SAMSUNG - Free user manual and instructions

Product type	Combined refrigerator with freezer
Brand	Samsung
Model	RB38C7B5C22
Dimensions (H x W x D)	185 cm x 60 cm x 66 cm
Net weight	70 kg
Total net capacity	380 L
Energy class	A++
Annual energy consumption	250 kWh/year
Supply voltage	220-240 V ~ 50 Hz
Rated current	1,2 A
Refrigerant	R600a
Cooling technology	No Frost (frost-free)
Freezer type	Bottom freezer compartment
Freezer capacity	100 L
Power failure autonomy	12 h
Freezing capacity	10 kg/24h
Interior lighting	LED
Vacation function	Yes
Open door alarm	Yes
Automatic defrost	Yes (No Frost)
Noise level	39 dB(A)
Climate class	SN-ST (temperate to subtropical)
Shelf material	Tempered glass
Number of doors	2
Spare parts available	Filters, shelves, door bins, door gaskets
Repairability (score)	8/10 (according to manufacturer data)
Care and cleaning	Clean with a soft cloth and soapy water. Avoid abrasive products.

Frequently Asked Questions - RB38C7B5C22 SAMSUNG

How to set the temperature of the Samsung RB38C7B5C22 refrigerator?

Use the control buttons on the front panel. Press Fridge to adjust the refrigerator temperature between 1°C and 7°C. The recommended temperature is 3°C.

Why is my refrigerator making noise?

Normal noises include the compressor, fan, and refrigerant circulation. If the noise is abnormal, check that the appliance is level and not touching furniture.

How to defrost the freezer?

The RB38C7B5C22 model is equipped with No Frost technology, manual defrosting is not necessary. Defrosting is done automatically.

What to do if the open door alarm sounds?

The alarm sounds if the door remains open for more than 2 minutes. Close it properly. If the problem persists, check the door gasket seal.

How to clean the inside of the appliance?

Unplug the appliance, remove food and shelves. Clean with a soft cloth dampened with warm water and white vinegar. Wipe with a dry cloth.

What is the estimated annual electricity consumption?

The annual consumption is approximately 250 kWh, according to EN 62552. This is equivalent to about 60 euros per year (average rate).

How to activate vacation mode?

Press the Vacation button (or hold the Fridge button for 3 seconds) to activate vacation mode. The refrigerator runs in energy-saving mode while maintaining a safe temperature.

Can I install non-genuine spare parts?

It is recommended to use genuine Samsung spare parts to ensure safety and performance. Contact an authorized service center.

What is the warranty for this appliance?

Samsung offers a manufacturer's warranty of 2 years (parts and labor). For compressors, the warranty may be extended to 10 years depending on the region.

How to reverse the door opening direction?

The door opening direction is reversible. Refer to the manual for detailed instructions. You will need tools such as a screwdriver and a Torx key. If you are not comfortable, call a professional.

USER MANUAL RB38C7B5C22 SAMSUNG

User servicing manual

1. You can check where to buy replacement parts at http://samsung.com
2. Visit the part purchase site and enter the model code of your product to check the parts available for purchase. The model code is labelled on the outer side of your product.
3. You can check the model code and version on the barcode label at the bottom left of the product.
4. For replacement parts, make sure the part name matches that of the illustration in this manual.
5. User-serviceable parts are limited to handles (some models only), gaskets, drawers, and hinges.

NOTE

Following the repair by a non-authorised service provider, self-repair or non-professional repair of the product, Samsung is not liable for any damage to the product, any injury or any other product safety issue caused by any attempt to repair the product which does not carefully follow these repair and maintenance instructions. Any damage to the product caused by an attempt to repair the product by any person other than a Samsung certified service provider will not be covered by the warranty.

CAUTION

• The part name listed on the site may differ from that in this manual. Please make sure you choose the right part name.
• Replacing hinges requires extreme caution because it involves detaching the door.
• Be sure to wear safety gloves while making repairs.

English

The actual image and provided parts of the refrigerator may differ, depending on the model and the country.

01 Top hinge 02 Gasket 03 Drawer 04 Handles (Applicable models only) 05 Middle hinge 06 Barcode label 07 Bottom hinge

English

Handle replacement

Model name looks like this: RB38**6****, RB38**2****, RL38**6****, RB3L**2****, RB36**6****, RB36**2****, RL36**6****, RL36**2****, RB34**6****, RB34**2****, RL34**6****, RL34**2****

What replaces the asterisks may differ depending on the model.

Asterisk(s) in the model code indicate a variant model and may replace (0-9) or (A-Z) in the model code.

CAUTION

• When replacing the door handle, take care not to scratch the front of the door.
• Firmly press the handles at the supports. Make sure there is no gap between the supports and the door.
• Tightly fasten the screws when attaching the handle.
• Check that the handle is firmly attached before using the product.

Tools required (not provided)

Phillips screwdriver Flat-head screwdriver

To detach the handles

NOTE

This procedure applies to both the fridge and freezer compartment.

1. Use a flat-head screwdriver to remove the screw covers.
2. After detaching the handle, attach the screw covers back on the screw holes.
3. Use a Phillips screwdriver to remove the screws and detach the handle.

NOTE

Use these screws to fasten the handle on the opposite side.

1. Assemble the new handle in the reverse order of disassembly.

English

Gasket replacement

CAUTION

Make sure you firmly attach the gasket. Otherwise, cold air from the refrigerator may leak.

To remove the gasket

Open the door and remove the gasket from the door.

To replace the gasket

Attach a new gasket to the refrigerator door. Make sure there is no gap between the new gasket and the door.

Drawer replacement

CAUTION

Check that the drawer is inserted properly into the rail during assembly.

To remove the drawer

Gently lift up the front of the drawer and slide it out.

To reattach the drawers

Reattaching the drawers follows the reverse order of their respective removal steps.

English

Hinge replacement

To replace the hinges, you must remove the doors first.

CAUTION

- When removing the doors, take extreme caution because the doors are heavy. - Before replacing the hinges, put a soft pad such as cardboard on the floor to prevent scratches on the door when you place the doors down. - As the hinges must be handled carefully and replaced by two or more persons, we recommend you to call for professional technical service.

- If you remove the hinge without holding the door, the door may fall and cause injury. - Ensure that the shaft is firmly tightened on the hinge. - Check that the hinge is firmly attached to the cabinet. - Make sure the wire connectors are connected properly. - Be careful not to damage the wires when fastening the top cover.

WARNING

- Tilting/laying the refrigerator requires a minimum of 2 people. - Disconnect the power cord before reversing the doors.

Tools required (not provided)

Phillips screwdriver, flat-head screwdriver, 11 mm spanner

10 mm socket wrench, 8 mm socket wrench, 10 mm spanner

English

Reversing the door

NOTE

For models with handles, reverse the handles first. (For detailed information, see the "Handle replacement (For models with bar handles)" section.)

1. With the fridge door closed, use a Phillips screwdriver to remove the screws fastening the top cover (A).
2. Gently lift the top cover (A) and place it on top of the refrigerator.

- Be careful when lifting the top cover (A). There is a wire connected underneath it.

1. Remove the wire and the wire connector placed on the holder underneath the top cover.

- This step may not apply to some models.

CAUTION

Do not pull the connectors too hard.

1. Disconnect the wire connector (A).
2. This step may not apply to some models.

1. Use a socket wrench (8 mm) to remove the screws fastening the top hinge (A).

CAUTION

To prevent the fridge door from falling, make sure to hold it tight while removing the screws.

1. Open the fridge door, and then lift the door to remove it from the middle hinge. Keep the door in a safe place.

CAUTION

The door is heavy. To prevent damage or injury, use caution while removing the door.

1. Open the freezer door, and then use a socket wrench (8 mm) to remove the screws fastening the bottom hinge (A).

1. With the freezer door sitting on the bottom hinge (A), slowly pull the bottom hinge (A) to remove it from the holder on the bottom of the refrigerator. Once the bottom hinge (A) is removed from the holder, remove it from the freezer door, and then pull the freezer door down to remove it from the middle hinge (B).

CAUTION

To prevent the freezer door from falling, make sure to hold the freezer door tight until it is safely removed from the middle hinge (B).

1. Use a Phillips screwdriver and socket wrench (10 mm) to remove the screws fastening the middle hinge (A).
2. Reassemble in the opposite order of disassembly after replacing the top, middle, and/or bottom hinge.

CAUTION

• Make sure the wire connectors are connected properly.

- Be careful not to damage the wires when fastening the top cover.

English

Repair Guide

Phillips screwdriver Flathead screwdriver

Phillips screwdriver Flathead screwdriver

Removing the handles

NOTE

Phillips screwdriver Flathead screwdriver

Open the door and remove the gasket from it.

Installing the gasket

01 Upper hinge 02 Door gasket 03 Door bin 04 Handles (only certain models) 05 Middle hinge 06 Barcode label 07 Lower hinge

Serbian

Replacing the handle

The model name looks like this: RB38**6****, RB38**2****, RL38**6****, RB3L**2****, RB36**6****, RB36**2****, RL36**6****, RL36**2****, RB34**6****, RB34**2****, RL34**6****, RL34**2****

The content that replaces the asterisks may vary depending on the model.

The asterisks in the model code indicate the model variant and may be replaced by digits (0–9) or letters (A–Z).

CAUTION

• When replacing the handle on the door, be careful not to scratch the front of the door.
• Press the handles firmly onto the supports. Make sure there is no gap between the supports and the door.
• Tighten the screws firmly when installing the handle.
• Before using the product, check that the handle is properly attached.

Required tools (not provided)

Open the door and remove the door gasket from it.

To replace the door gasket

Install the new door gasket on the refrigerator door. Make sure there is no gap between the new gasket and the door.

Replacing the drawer

CAUTION

During installation, check that the drawer is properly inserted into the guides.

To remove the drawer

Gently lift the front of the drawer upward and pull it out.

To replace the drawer

1. With the refrigerator doors closed, use a Phillips screwdriver to remove the screws securing the top cover (A).
2. Carefully lift the top cover (A) and place it on top of the refrigerator.

- Be careful when lifting the top cover (A). There are connected wires underneath it.

1. Remove the cable and cable connector from the holder located under the top cover.

- This step does not apply to all models.

CAUTION

1. While the freezer door rests on the lower hinge (A), slowly pull the lower hinge (A) to remove it from the holder on the bottom side of the refrigerator. Once the lower hinge (A) is removed from the holder, remove it from the freezer door, then pull the freezer door downward to detach it from the middle hinge (B).

! CAUTION

01 Top hinge 02 Gasket 03 Drawer 04 Handles (only on certain models) 05 Middle hinge 06 Barcode label 07 Bottom hinge

Croatian

Replacing the handles

The model name looks like this: RB38**6****, RB38**2****, RL38**6****, RB3L**2****, RB36**6****, RB36**2****, RL36**6****, RL36**2****, RB34**6****, RB34**2****, RL34**6****, RL34**2****

1. Use a flat-head screwdriver to remove the screw covers.
2. After detaching the handle, attach the screw covers back onto the screw holes.
3. Use a Phillips screwdriver to remove the screws and detach the handle.

NOTE

Use the specified screws to attach the handle to the opposite side.

1. Assemble the new handle in the reverse order of detachment.

Croatian

Replacing the gasket

CAUTION

Make sure to firmly attach the gasket. Otherwise, cold air from the refrigerator could escape.

To remove the gasket

Open the door and remove the gasket from the door.

To replace the gasket

Carefully lift the front part of the drawer and pull it out.

Reinstalling the drawers

1. Using a ratchet wrench (8 mm), remove the screws that secure the upper hinge (A).

CAUTION

To prevent the door from falling, hold it firmly while removing the screws.

01 Upper hinge 02 Gasket 03 Drawer 04 Handles (only on models that have them) 05 Middle hinge 06 Barcode label 07 Lower hinge

Albanian

Phillips screwdriver Flathead screwdriver

Cross-head screwdriver Flat-head screwdriver

Open the door and remove the gasket from the door.

To replace the gasket

Open the door and remove the gasket from the door.

Replacing the gasket

Attach the new gasket to the refrigerator door. Make sure there is no gap between the new gasket and the door.

Replacing the drawer

CAUTION

Carefully lift the front part of the drawer and pull it out.

Reinstalling the drawer

1. Keep the refrigerator door closed, then use a Phillips screwdriver to remove the screws securing the top cover (A).
2. Carefully lift the top cover (A) and place it on the top of the refrigerator.