iConnect Audio 2+ - DJ Equipment iConnectivity - Free user manual and instructions
Find the device manual for free iConnect Audio 2+ iConnectivity in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type de produit | USB Audio Interface / DJ Equipment |
| Marque | iConnectivity |
| Modèle | iConnect Audio 2+ |
| Entrées audio | 2 x Combo XLR/TRS (mic/line), 2 x RCA (line) |
| Sorties audio | 2 x TRS (line), 1 x Headphone (1/4" stereo) |
| MIDI | 1 x MIDI In, 1 x MIDI Out (DIN) |
| Connectivité USB | USB-B (USB 2.0) |
| Échantillonnage | Up to 24-bit/96kHz |
| Alimentation | USB bus-powered (or optional DC adapter) |
| Dimensions (approx.) | 14.5 x 10.5 x 4.5 cm |
| Poids (approx.) | 0.5 kg |
| Fonctions principales | Direct monitoring, low-latency operation, class-compliant (macOS/iOS), drivers for Windows |
| Entretien et nettoyage | Clean with dry soft cloth; avoid liquids and abrasive materials |
| Sécurité | Do not expose to extreme temperatures or moisture; use only provided USB cable |
| Pièces détachées | Not user serviceable; contact iConnectivity support for warranty service |
| Réparabilité | No repair parts available; device must be replaced or serviced by authorized center |
| Garantie | Refer to iConnectivity warranty policy (typically 1-2 years) |
Frequently Asked Questions - iConnect Audio 2+ iConnectivity
How do I set up the iConnect Audio 2+ with my DJ software?
Connect the device via USB to your computer, install the appropriate driver for Windows (macOS/iOS are class-compliant). In your DJ software, select iConnect Audio 2+ as the audio device. Ensure inputs and outputs are configured correctly.
Does the iConnect Audio 2+ work with iPad or iPhone?
Yes, it is class-compliant and works with iOS devices via a Lightning to USB camera adapter. No additional drivers are needed.
Can I use the MIDI ports to control DJ software?
Yes, the MIDI In/Out allow connection with controllers and keyboards. The device acts as a MIDI interface, sending MIDI data to your computer.
What is the maximum sample rate and bit depth?
The iConnect Audio 2+ supports up to 24-bit resolution and sample rates up to 96 kHz.
How do I enable direct monitoring?
Direct monitoring is available by adjusting the monitor mix knob on the front panel. This allows you to hear your input signal without latency.
Why is there no sound from my headphones?
Check that the headphone volume knob is turned up and that the headphone output is selected in your audio settings. Also ensure the headphone impedance is compatible (typically 32-600 ohms).
Where can I download the latest drivers?
Drivers for Windows are available on the iConnectivity official website. For macOS and iOS, no drivers are required.
What power supply does the device use?
It is primarily USB bus-powered. However, if you need extra power (e.g., for high-impedance microphones), you can use an optional 5V DC power supply (center positive, 2.1mm barrel).
Can I connect a microphone directly to the XLR input?
Yes, the combo jacks accept both XLR (mic) and TRS (line) inputs. For microphones, ensure phantom power is enabled if required (via a switch on the front panel).
How do I reset the device to factory defaults?
There is no user-accessible factory reset. If you experience issues, disconnect USB, power off, and reconnect. For persistent problems, contact iConnectivity support.
User questions about iConnect Audio 2+ iConnectivity
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your DJ Equipment in PDF format for free! Find your manual iConnect Audio 2+ - iConnectivity and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. iConnect Audio 2+ by iConnectivity.