MDD94-E - Beer dispenser Micro Matic - Free user manual and instructions
Find the device manual for free MDD94-E Micro Matic in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | Beer dispenser (tireuse à bière) |
| Brand | Micro Matic |
| Model | MDD94-E |
| Dimensions (approx.) | 45 cm (H) x 30 cm (W) x 50 cm (D) |
| Weight (approx.) | 18 kg |
| Power supply | 220-240 V ~ 50/60 Hz, electric cooling |
| CO2 compatibility | Yes, external CO2 cylinder connection |
| Cooling system | Compressor-based, adjustable temperature |
| Number of taps | 1 (single tap, usually for one keg) |
| Keg capacity | Standard 20 L or 30 L keg (depending on model variant) |
| Temperature range | 2°C to 8°C |
| Material | Stainless steel and plastic |
| User interface | Analog temperature dial and tap handle |
| Cleaning | Disassemble and wash tap, lines, and drip tray with warm soapy water |
| Maintenance | Sanitize beer lines regularly, replace CO2 regulator as needed |
| Safety features | Grounded plug, pressure relief valve, over-temperature protection |
| Spare parts availability | Yes, via Micro Matic distributors (taps, lines, cooling unit) |
| Repairability | Moderate – accessible components, professional service recommended |
| Included accessories | Beer tap, drip tray, gas connector, user manual |
| User manual | Available for free download in PDF on notice-facile.com |
Frequently Asked Questions - MDD94-E Micro Matic
How do I connect the CO2 cylinder?
Attach the CO2 regulator to the cylinder, then connect the gas line to the input on the back of the MDD94-E. Set the recommended pressure (usually 10-15 psi) for your beer type.
What size keg fits the MDD94-E?
The MDD94-E is designed for standard 20-liter or 30-liter kegs with a sankey coupling. Always check the specific model compatibility.
How do I clean the beer lines?
Disconnect the keg, run a cleaning solution (e.g., BLC) through the lines using a cleaning pump, then flush with fresh water. Reassemble and sanitize before next use.
Why is the beer too foamy?
Possible causes: incorrect CO2 pressure (too high), warm beer (check cooling), dirty lines, or over-agitation. Adjust pressure, clean lines, and ensure keg is properly chilled.
How do I adjust the temperature?
Turn the thermostat dial inside the cabinet to the desired setting. Allow 2-4 hours for temperature stabilization. Recommended serving temperature is 3-5°C.
The cooler is not working – what should I check?
Check power connection, ensure the thermostat is on, verify the compressor is running (listen for hum). If still not cooling, contact a qualified technician.
Can I use this dispenser without CO2?
No, CO2 is required to push beer from the keg and maintain carbonation. Without it, the beer will not dispense and will go flat.
How often should I clean the drip tray?
Empty and rinse the drip tray daily to prevent bacterial growth. Wash with mild soap weekly.
Where can I find replacement parts?
Authorized Micro Matic dealers or online retailers stock parts like faucets, lines, and regulators. Check the model number MDD94-E for compatibility.
The manual is not in my language – can I get a translation?
Yes, on notice-facile.com you can request a translated version by selecting your language and providing your email.
User questions about MDD94-E Micro Matic
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Beer dispenser in PDF format for free! Find your manual MDD94-E - Micro Matic and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MDD94-E by Micro Matic.
USER MANUAL MDD94-E Micro Matic
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Micro Matic
Model : MDD94-E
Category : Beer dispenser