324 Plus True RMS - Measuring equipment FLUKE - Free user manual and instructions
Find the device manual for free 324 Plus True RMS FLUKE in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | True RMS Clamp Meter |
| Display | 6000 counts, backlit LCD |
| AC Current Range | 0 to 400 A |
| DC Current Range | 0 to 400 A |
| AC Voltage Range | 0 to 600 V |
| DC Voltage Range | 0 to 600 V |
| Resistance Range | 0 to 40 kΩ |
| Capacitance Range | Up to 1000 μF |
| Frequency Range | Up to 100 kHz |
| Temperature Measurement | -40 to 400 °C (with included thermocouple) |
| True RMS | Yes, AC coupled |
| Continuity Beeper | Yes |
| Data Hold | Yes |
| Min/Max/Average | Yes |
| Auto Range | Yes |
| Input Impedance | 10 MΩ (voltage) |
| Safety Rating | CAT III 600 V, CAT IV 300 V |
| Power Supply | 2 AA batteries (1.5 V) |
| Battery Life | Approximately 400 hours typical |
| Dimensions | 207 x 75 x 41 mm |
| Weight | 260 g (including batteries) |
| Jaw Opening | 30 mm |
| Operating Temperature | 0 °C to 50 °C |
| Storage Temperature | -20 °C to 60 °C |
| Warranty | 3 years |
Frequently Asked Questions - 324 Plus True RMS FLUKE
How do I measure AC current with the Fluke 324 Plus?
Set the rotary switch to the A~ position. Clamp the jaw around a single conductor. The reading appears on the display.
How do I measure DC current?
Set the rotary switch to the A position with DC selected. Clamp around the conductor. For best accuracy, zero the meter before clamping.
How do I measure voltage?
Insert the test leads into the V/Ω and COM jacks. Set the rotary switch to V~ for AC or V for DC. Touch the probes to the test points.
How to change the batteries?
Turn the meter off. Remove the battery door screw and lift the door. Replace two AA batteries. Reattach the door and tighten the screw.
What is the accuracy of the meter?
Basic DC voltage accuracy is ±1% + 5 digits. See the manual for detailed specifications.
Can I measure temperature with this meter?
Yes. Insert a K-type thermocouple into the COM and V/Ω jacks. Set the rotary switch to °C or °F.
How do I use the data hold feature?
Press the HOLD button to freeze the current reading. Press again to release.
What does the Min/Max/Average mode do?
Press MIN/MAX to enter recording mode. The meter captures the minimum, maximum, and average readings.
How do I test continuity?
Set the rotary switch to the Ω position. Press the CONT button to activate continuity beeper. Touch probes to the circuit; a beep sounds if resistance is below ~50 Ω.
Is the meter autoranging?
Yes, the Fluke 324 Plus automatically selects the appropriate range for voltage, resistance, and capacitance measurements.
User questions about 324 Plus True RMS FLUKE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Measuring equipment in PDF format for free! Find your manual 324 Plus True RMS - FLUKE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 324 Plus True RMS by FLUKE.
USER MANUAL 324 Plus True RMS FLUKE
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : FLUKE
Model : 324 Plus True RMS
Category : Measuring equipment