Sprint Evo TSBE1401 019 - Vacuum Cleaner HOOVER - Free user manual and instructions

Product Type	Upright Vacuum Cleaner
Brand	Hoover
Model	Sprint Evo TSBE1401 019
Dimensions (L x W x H)	30 x 25 x 110 cm
Weight	5.5 kg
Power Supply	220-240 V ~ 50/60 Hz
Power Consumption	750 W
Cord Length	8 m
Dust Capacity	1.5 L
Filter Type	HEPA washable filter
Filtration System	Cyclonic multi-stage
Bagless	Yes
Noise Level	78 dB
Accessories Included	Crevice tool, dusting brush, upholstery tool
Handle Type	Ergonomic with trigger release
Wheels	2 large rear wheels, 1 front swivel wheel
Maintenance	Empty dust bin, clean filter regularly
Filter Washable	Yes, every 3 months
Dust Bin Release	One-button release
Safety Features	Thermal cut-off, overload protection
Spare Parts Available	Filters, belts, brush rolls
Repairability	User-serviceable parts
Warranty	2 years

Frequently Asked Questions - Sprint Evo TSBE1401 019 HOOVER

How do I empty the dust bin?

Press the release button on the dust bin to remove it from the vacuum. Hold over a trash can and press the bottom release to empty. Reattach by sliding back into place until it clicks.

How often should I clean the filter?

Clean the HEPA filter every 3 months or when the suction seems reduced. Wash with cold water and let it dry completely for 24 hours before reinserting.

My vacuum is losing suction. What could be the cause?

Check for blockages in the hose, brush roll, or dust bin. Also ensure the filter is clean. If the dust bin is full, empty it.

How do I replace the brush roll?

Disconnect the vacuum from power. Use a screwdriver to remove the brush roll cover, lift out the old roll, and replace with a new one. Ensure the belt is properly aligned.

Is the vacuum bagless?

Yes, the Hoover Sprint Evo is bagless. It uses a transparent dust bin that you empty directly.

What accessories come with the vacuum?

The vacuum includes a crevice tool, dusting brush, and upholstery tool. These can be stored on-board.

How long is the power cord?

The power cord is 8 meters long, allowing you to clean large areas without switching outlets.

Can I use this vacuum on hardwood floors?

Yes, the brush roll can be turned off for bare floors, or you can use the included hard floor setting if available. For delicate surfaces, use the appropriate attachment.

What should I do if the vacuum overheats?

If the vacuum shuts off due to overheating, turn it off and unplug it. Check for blockages and clean the filter. Let it cool for at least 30 minutes before restarting.

Where can I purchase replacement parts?

Replacement parts such as filters, brush rolls, and belts are available on the Hoover website or from authorized retailers.

USER MANUAL Sprint Evo TSBE1401 019 HOOVER

*Grain and Mio.

INSTRUCTIONS FOR SAFE USE

This appliance should only be used for domestic cleaning, as described in this user guide. Please ensure that this guide is fully understood before operating the appliance.

Do not leave the appliance plugged in. Always switch off and remove the plug from the socket after use, or before cleaning the appliance or any maintenance task.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

If the power cord is damaged stop using the appliance immediately. To avoid a safety hazard, an authorised HOOVER service engineer must replace the power cord.

Keep hands, feet, loose clothing and hair away from rotating brushes.

Use only attachments, consumables or spares recommended or supplied by HOOVER.

Static electricity: Some carpets can cause a small build up of static electricity. Any static discharge is not hazardous to health.

Do not use your appliance out of doors or on any wet surface or for wet pick up.

Do not pick up hard or sharp objects, matches, hot ashes, cigarette ends or other similar items.

Do not spray with or pick up flammable liquids, cleaning fluids, aerosols or their vapours.

Do not run over the power cord when using your appliance or remove the plug by pulling on the power cord.

Do not continue to use your appliance if it appears faulty.

HOOVER service: To ensure the continued safe and efficient operation of this appliance we recommend that any servicing or repairs are only carried out by an authorised HOOVER service engineer.

Do not stand on or wrap the cord around arms or legs when using your appliance.

Do not use the appliance to clean animals or people.

Do not position the appliance above you when cleaning the stairs.

GETTING TO KNOW YOUR CLEANER

A. Cleaner main body

B. Dust Container

C. Dust Container Handle

D. Dust Container Release Button

E. Cleaner Handle

F. On/Off Button

G. Cord Rewind Button

H. Nozzle Parking Slot

I. Exhaust Filter Cover

J. Hose

K. Hose Release Button

L. Hose Handle

M. Suction Regulator*

N. Standard Tube*

O. Telescopic Tube⁴

P. Telescopic Tube Adjuster*

Q. Carpet & Floor Nozzle**

R. Floor Type Selector Pedal

S. Pre-motor Filter and Protective Mesh

T. Exhaust Filter

U. 2 in 1 Tool (Crevice Tool/Dusting Brush)*

V. Pet Hair Remover Mini Turbo Nozzle^®

W. Allergen Remover Mini Turbo Nozzle*

X. Hard Floor Nozzle*

ASSEMBLING YOUR CLEANER

Remove all components from the packaging.

1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. To release the hose: simply press the two hose release buttons on the hose end and pull it out. [2]
2. Connect the hose handle to the telescopic tube* upper end. [3]
3. Connect the telescopic tube* lower end to the carpet and floor nozzle**.[4]

1

* Certain models only

** May vary depending on model

USING YOUR CLEANER

1. Extract power cord and plug it into the power supply. [5] Do not pull the cord beyond the red marker.
2. Adjust the telescopic tube* to the desired height by moving the telescopic tube adjuster up and raise or lower the handle to the most comfortable cleaning position. [10]
3. Carpet & Floor Nozzle**. Press the floor type selector pedal on the nozzle [6] to select the ideal cleaning mode for the floor type. Hard Floor - Brushes are lowered to protect the floor. Carpet - Brushes are raised for the deepest clean.
4. Switch the cleaner on by pressing the On/Off button on the cleaner main body. [7]
5. Vary the suction as desired by closing or opening the suction regulator* on the hose handle, [11]
6. Switch off at the end of use by pressing the On/Off button. [7] Unplug and press the cord rewind button to wind the power cord back into the cleaner. [8]
7. To store your cleaner, park the nozzle in the parking slot at the rear of the cleaner main body. [9]

ACCESSORIES

All accessories can be fitted to the hose handle or the end of the tubes.

2 In 1 Tool combines several functions into one tool:

Crevice Tool – For corners and hard to reach areas.

Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. [20]

Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs removal.

Allergen Remover Mini Turbo Nozzle® – Use the mini turbo nozzle on stairs or for deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen removal.

Hard Floor Nozzle* – For parquet floors and other delicate floors.

IMPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.

CLEANER MAINTENANCE

Emptying the Dust Container

When the dust reaches the max level indicator on the container, empty the dust container.

IMPORTANT: To maintain optimum performance, do not allow the dust to sit higher than the max level.

1. Release the dust container by sliding the dust container release button towards the front of the cleaner. Lift the dust container from the cleaner main body. [12]

1. Before emptying the Dust Container, gently tap it against the side of a bin to release any excess dust from the filter.
2. To empty the Dust Container, hold the Dust Container over a bin with one hand and use the other hand to press the Dust Container Flap Opening Button to release the dust into the bin. [13]
3. Close the Dust Container Flap and refit the Dust Container to the cleaner main body.

Cleaning the Washable Filters

The cleaner is fitted with a pre-motor and exhaust filter. To maintain optimum cleaning performance, regularly clean the filters. Remove excess dust from the filters by gently tapping them against the side of a bin. The filters should be washed after every 5 container empties.

IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean your filters may result in air blockage, overheating and product failure. This may invalidate your guarantee.

IMPORTANT: Regularly check and maintain the filters by following the filter maintenance instructions, it is also recommended that you purchase new filters after every 3rd filter wash. This will maintain your cleaners performance.

To access the pre-motor filter:

1. Empty the Dust Container as described in 'Emptying the Dust Container'. Then, keeping the Dust Container Flap open:
2. Remove the pre-motor filter by rotating it clockwise at the bottom of the Dust Container. [14]
3. Separate the protective mesh from the filter. [15] Gently tap both the protective mesh and the filter against the side of a bin to remove excess dust and wash both of them under warm water. [16] Do not use hot water or detergents.
4. Remove excess water from the filter and leave it to dry fully before reusing. [19]
5. Once the filter is fully dry, reassemble the filter pack (protective mesh and filter) and refit to cleaner.

IMPORTANT: Do not use the product without the pre-motor filter pack fitted.

IMPORTANT: Always ensure the filter packs are fully dry before use.

To access the exhaust filter:

1. Unclip the exhaust grid from the rear of the cleaner. [17]
2. Separate the filter from the grid and wash the filter under warm water. [18] Do not use hot water or detergents.
3. Remove excess water from the filter and leave to dry fully before reusing. [19]
4. Remount the filter into the grid and refit it to the cleaner.

Remember: Do not use hot water or detergents. In the unlikely event of the filters becoming damaged, fit a Genuine Hoover consumable. Do not try and use the product without a filter fitted.

Removing a Blockage

1. Check if the Dust Container is full. If so refer to 'Emptying The Dust Container'.
2. If the Dust Container is empty, but suction is still low; A. Do the filters need cleaning? If so refer to 'Cleaning the Washable Filters'. B. Check if there is any other blockage in the system - Use a rod or a pole to remove any blockage from the tubes or hose. C. Check for and clear any blockage in the Nozzle

Warning - If the cleaner is used for a significant period of time with a blockage, a thermal cut out will switch the cleaner off to prevent overheating. The bag check indicator turn green once the cleaner has switched off to signal that the thermal cut out has been activated. If this should happen, switch the cleaner off, unplug and correct the fault. It will take about 45 minutes for the cut out to automatically reset.

USER CHECKLIST

Should you have a problem with the product, complete this simple user checklist before calling your local Hoover service.

• Is there a working electricity supply to the cleaner? Please check with another electrical appliance. • Is the Bag over-filled? Please refer to 'Cleaner Maintenance'. • Is the filter blocked? Please refer to 'Cleaner Maintenance' • Is the hose or nozzle blocked? Please refer to 'Removing a Blockage'.
• Has the cleaner overheated? If so, it will take approximately 45 minutes to automatically reset.

IMPORTANT INFORMATION

Hoover Spares and Consumables

Always replace parts with genuine Hoover spares. These are available from your local Hoover dealer or direct from Hoover. When ordering parts always quote your model number.

CONSUMABLES

• Filter kit: U66, 35601328 (EPA pre-motor filter+ protective mesh and exhaust filter)

SPARES:

• Complete Flexible hose: D137 35601329 • Carpet & Floor nozzle: G82,35600417 • Mini Turbo nozzle: J20.09200356 • Hard Floor nozzle: G87PC, 35600655

Quality

Hoover's factories have been independently assessed for quality. Our products are made using a quality system which meets the requirements of ISO 9001.

The Environment

The symbol on this appliance indicates that this appliance may not be treated as household waste. Instead it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this appliance, please contact your local city office, your household and waste disposal service or the shop where you purchased the appliance.

CE This appliance complies with the European Directives 2006/95/EC, 2004/108/EC and 2011/65/EU.

HOOVER Limited, Pentrebach, Merthyr Tydfil, Mid Glamorgan, CF48 4TU, UK

Your Guarantee

The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee. Subject to change without notice.