EL-35 - Water pump ZODIAC - Free user manual and instructions
Find the device manual for free EL-35 ZODIAC in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Water pump |
| Brand | Zodiac |
| Model | EL-35 |
| Application | Pool filtration and water circulation |
| Dimensions (L x W x H) | Approx. 30 x 20 x 25 cm |
| Weight | Approx. 10 kg |
| Power Supply | 230 V, 50 Hz |
| Power Consumption | 750 W |
| Flow Rate | Up to 120 L/min |
| Max Head | 8 m |
| Motor Type | Single-phase induction motor |
| Protection | Thermal overload protection |
| Self-Priming | Yes |
| Materials | Thermoplastic body, stainless steel shaft |
| Seal Type | Mechanical seal |
| Inlet/Outlet Diameter | 1.5 inch (38 mm) |
| Noise Level | < 70 dB(A) |
| Maintenance | Clean strainer basket regularly, check seals annually |
| Safety Features | IPX5 water resistance, ground fault protection |
| Spare Parts Available | Yes, impeller, seal kit, capacitor |
| Warranty | 2 years |
Frequently Asked Questions - EL-35 ZODIAC
How do I install the Zodiac EL-35 water pump?
Ensure the pump is placed on a stable, level surface. Connect inlet and outlet pipes with proper sealing. Wire the pump to a 230V supply with a residual current device (RCD). Prime the pump by filling the strainer basket with water before starting.
How do I prime the pump?
Open the strainer lid, fill the basket completely with water, then close the lid securely. Start the pump; it should self-prime within a few minutes. If not, check for air leaks.
Why is my pump noisy?
Noise can be due to cavitation (low water level), debris in the impeller, or worn bearings. Check water level, clean the strainer basket, and listen for unusual sounds indicating mechanical wear.
How do I clean the strainer basket?
Turn off the pump and disconnect power. Unscrew the strainer lid, remove the basket, and rinse it with water. Remove any debris. Replace basket and tighten lid. Restart pump.
What should I do if the pump leaks water?
Check that all connections are tight. Inspect the mechanical seal for wear. A leaking seal must be replaced using the Zodiac seal kit. Also ensure the strainer lid O-ring is clean and lubricated.
Can the pump run dry?
No, running dry will damage the mechanical seal and motor. Always ensure the pump is primed with water before operation. Use a flow switch or dry-run protection if needed.
What is the maximum operating temperature?
The pump is designed for water temperatures up to 40°C (104°F). Do not use for hot water or chemicals.
How do I winterize the pump?
Drain all water from the pump and pipes. Remove strainer basket and store indoors. Disconnect and store the pump in a frost-free location. Ensure no water remains that could freeze and crack the housing.
Where can I find spare parts like impeller or seal?
Spare parts are available from authorized Zodiac dealers or online. Use part numbers: Impeller #EL35-IMP, Seal Kit #EL35-SEAL, Capacitor #EL35-CAP. Always use genuine parts.
Why does the pump trip my circuit breaker?
This may indicate a short circuit or motor overload. Check for damaged wiring or a seized impeller. If the pump continues to trip, consult a qualified electrician. Ensure the breaker is rated for the pump's amperage.
User questions about EL-35 ZODIAC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water pump in PDF format for free! Find your manual EL-35 - ZODIAC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. EL-35 by ZODIAC.
USER MANUAL EL-35 ZODIAC
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ZODIAC
Model : EL-35
Category : Water pump