Aironet 1602i - Access Point CISCO - Free user manual and instructions
Find the device manual for free Aironet 1602i CISCO in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Wireless Access Point |
| Brand | Cisco |
| Model | Aironet 1602i |
| Wireless Standard | IEEE 802.11a/b/g/n (Dual-Band) |
| Frequency Bands | 2.4 GHz and 5 GHz |
| MIMO Configuration | 3x3:3 |
| Maximum Data Rate | 450 Mbps (2.4 GHz), 450 Mbps (5 GHz) |
| Antenna Type | Integrated omnidirectional dipole (internal) |
| Interfaces | 1 x 10/100/1000 Ethernet (PoE), 1 x Console RJ-45 |
| Power Source | Power over Ethernet (802.3af) or optional AC adapter |
| Power Consumption | 12.95 W (typical) |
| Security | WPA/WPA2, WEP, 802.1X, multiple SSIDs, VLAN support |
| Management | Web-based GUI, CLI, SNMP, Cisco Wireless Control System |
| Mounting | Ceiling or wall mount (bracket included) |
| Operating Temperature | 32 to 104°F (0 to 40°C) |
| Dimensions (W x D x H) | 8.5 x 8.5 x 1.2 in (216 x 216 x 31 mm) |
| Weight | 1.4 lb (0.64 kg) |
| LED Indicators | Power, Ethernet, Radio, Status |
| Compliance | FCC, CE, IC, Wi-Fi Alliance |
| Maintenance | Clean with dry cloth; avoid liquids |
| Repairability | No user-serviceable parts; contact Cisco support |
Frequently Asked Questions - Aironet 1602i CISCO
What is the default IP address of the Cisco Aironet 1602i?
The default IP address is 10.0.0.1 if not configured via DHCP. You can access the web interface by connecting to this IP.
Does the Cisco Aironet 1602i support PoE?
Yes, it supports Power over Ethernet (802.3af). You can power it using a PoE switch or injector.
What is the maximum number of clients supported?
The Aironet 1602i can support up to 200 simultaneous clients, though performance may vary based on environment.
Can I use it as a standalone access point?
Yes, it supports both autonomous and controller-based modes. In autonomous mode, it operates independently.
How do I reset the access point to factory defaults?
Press and hold the MODE button on the back while powering on, until the LED turns amber (about 10 seconds). Release after it flashes red.
What security protocols does it support?
It supports WEP, WPA, WPA2 (TKIP/AES), 802.1X, and multiple SSIDs with VLAN mapping.
Is the Aironet 1602i dual-band?
Yes, it operates on both 2.4 GHz and 5 GHz bands simultaneously, providing up to 450 Mbps on each band.
What type of antennas does it use?
It uses internal omnidirectional antennas, each with a gain of 4 dBi for 2.4 GHz and 5 dBi for 5 GHz. No external antennas are provided.
Can I mount it on a wall?
Yes, it can be mounted on a ceiling or wall using the included mounting bracket. Ensure the bracket is securely attached.
Where can I download the latest firmware?
You can download firmware from the Cisco website under Software Download > Wireless > Access Points > Aironet 1600 Series.
User questions about Aironet 1602i CISCO
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Point in PDF format for free! Find your manual Aironet 1602i - CISCO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Aironet 1602i by CISCO.
USER MANUAL Aironet 1602i CISCO
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : CISCO
Model : Aironet 1602i
Category : Access Point