INFO-1 - Multimeter MGL Avionics - Free user manual and instructions
Find the device manual for free INFO-1 MGL Avionics in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Digital Multimeter |
| Brand | MGL Avionics |
| Model | INFO-1 |
| Display | LCD, 3-1/2 digits |
| DC Voltage Range | 200mV to 1000V |
| AC Voltage Range | 200mV to 750V |
| DC Current Range | 200µA to 10A |
| Resistance Range | 200Ω to 200MΩ |
| Capacitance Measurement | Yes, up to 200µF |
| Frequency Measurement | Yes, up to 20kHz |
| Diode Test | Yes |
| Continuity Test | Yes, with buzzer |
| Data Hold | Yes |
| Backlight | Yes |
| Auto-ranging | Yes |
| Safety Rating | CAT II 1000V, CAT III 600V |
| Power Supply | 9V battery (included) |
| Dimensions | Approx. 180 x 87 x 47 mm |
| Weight | Approx. 350 g |
| Overload Protection | Yes |
| Spare Parts | Test leads, 9V battery, fuse |
| Reparability | Fuse and battery replaceable; professional repair for other issues |
| Care | Clean with dry cloth, avoid moisture, remove battery if not used for long |
| Safety | Observe rated voltage limits, do not measure high-energy circuits without proper protection |
Frequently Asked Questions - INFO-1 MGL Avionics
How do I measure DC voltage?
Set the rotary switch to the DCV range. Connect the red test lead to the VΩmA jack and the black lead to the COM jack. Touch the probes to the test points and read the voltage on the display.
How do I measure current?
Select the DC A or AC A range. For currents up to 200mA, use the VΩmA jack; for currents up to 10A, use the 10A jack. Always connect the meter in series with the circuit.
How do I measure resistance?
Turn off power to the circuit. Set the dial to Ω. Connect the probes across the resistor. The display shows the resistance value. For high resistance, use the appropriate range.
What does the continuity beep mean?
When the continuity function is selected, the meter beeps if the resistance between the probes is less than about 50 Ω (typical). This indicates a closed circuit or low resistance path.
How do I replace the battery?
Turn off the meter and remove the test leads. Open the battery compartment with a screwdriver. Replace the 9V battery with a new one, observing polarity. Close the compartment securely.
What is the maximum voltage I can measure?
The INFO-1 can measure up to 1000V DC and 750V AC. Do not exceed these limits to avoid damage or injury. Always adhere to the safety ratings (CAT II 1000V, CAT III 600V).
How do I use the data hold function?
Press the HOLD button to freeze the current reading on the display. Press it again to release the hold. This is useful when measuring in dimly lit areas or when you cannot look at the meter.
How do I test a diode?
Set the dial to the diode symbol (typically a diode icon). Connect the red probe to the anode and black to the cathode. A typical forward voltage drop (0.5-0.8V for silicon) indicates a good diode. OL indicates open or reverse biased.
What does 'OL' mean on the display?
OL stands for Overload or Open Loop. It means the measured value exceeds the selected range or the circuit is open. Try a higher range or check your connections.
How do I clean my multimeter?
Use a soft, dry cloth to wipe the casing. Do not use abrasive cleaners or solvents. Keep the input jacks clean and dry. Remove the battery if storing for extended periods.
User questions about INFO-1 MGL Avionics
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Multimeter in PDF format for free! Find your manual INFO-1 - MGL Avionics and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. INFO-1 by MGL Avionics.
USER MANUAL INFO-1 MGL Avionics
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : MGL Avionics
Model : INFO-1
Category : Multimeter