KR614-OSDP - Security System ZKTeco - Free user manual and instructions
Find the device manual for free KR614-OSDP ZKTeco in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | OSDP Access Control Reader |
| Brand | ZKTeco |
| Model | KR614-OSDP |
| Communication Protocol | OSDP (RS-485) |
| Card Technology | 125kHz EM, 13.56MHz MIFARE, DESFire, etc. |
| Read Range | Up to 10 cm (depending on card type) |
| Dimensions (W x H x D) | 120 x 75 x 20 mm |
| Weight | 150 g |
| Power Supply | 12V DC, 100 mA max |
| IP Rating | IP65 (weatherproof) |
| Operating Temperature | -20°C to 60°C |
| Material | ABS plastic with UV protection |
| LED Indicators | 3-color (Red, Green, Blue) |
| Buzzer | Yes (programmable tones) |
| Connection | 4-wire: V+, GND, D+, D- (RS-485) |
| Compatibility | ZKTeco controllers supporting OSDP |
| Mounting | Wall mount with included screws and template |
| Certifications | CE, FCC, RoHS |
| Tamper Protection | Built-in tamper switch |
| Firmware Upgrade | Via OSDP commands |
| Memory (Card Capacity) | Depends on controller |
| Wiegand Support | No (OSDP only) |
Frequently Asked Questions - KR614-OSDP ZKTeco
How do I wire the KR614-OSDP reader?
Connect the 4 wires: V+ to 12V DC, GND to ground, D+ to RS-485+, and D- to RS-485-. Ensure the controller's OSDP address matches.
What is the default OSDP address of the KR614-OSDP?
The default OSDP address is usually 127 or 0x7F. You can change it via controller or configuration card.
Can the KR614-OSDP be used outdoors?
Yes, the reader has an IP65 rating, making it suitable for outdoor use. Avoid direct exposure to heavy rain or sun for prolonged periods.
How to reset the KR614-OSDP to factory defaults?
To reset, power off the reader, short the factory reset pins (if available) or use a configuration card provided by ZKTeco. Typical process: power on while holding the reset button for 5 seconds.
Which card types are supported?
The reader supports 125kHz EM and 13.56MHz MIFARE (Classic, Plus, DESFire) cards. Some versions also support NFC mobile credentials.
What is the maximum read range?
Read range depends on card type and environment. Typically up to 10 cm for MIFARE and up to 5 cm for EM cards.
Is the KR614-OSDP compatible with third-party controllers?
The reader uses OSDP protocol, which is an open standard. It should work with any OSDP-compliant controller. However, full feature support may vary. Check your controller's documentation.
How do I clean the reader?
Use a soft, damp cloth with mild soap. Avoid abrasive cleaners or solvents. Do not spray liquids directly; apply to cloth first.
What does the LED colors indicate?
Typical indications: Red = idle/standby, Green = access granted, Blue = card read or communication active. Blinking patterns may indicate errors (e.g., tamper). Consult manual for exact meanings.
Can I use the KR614-OSDP with a Wiegand controller?
No, this model is OSDP-only. If you need Wiegand, consider the KR614-W or other Wiegand variants from ZKTeco.
User questions about KR614-OSDP ZKTeco
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Security System in PDF format for free! Find your manual KR614-OSDP - ZKTeco and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. KR614-OSDP by ZKTeco.
USER MANUAL KR614-OSDP ZKTeco
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ZKTeco
Model : KR614-OSDP
Category : Security System