SoundLink MW-1608 - Mixer KORG - Free user manual and instructions
Find the device manual for free SoundLink MW-1608 KORG in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of Product | Analog Mixing Console |
| Brand | Korg |
| Model | SoundLink MW-1608 |
| Number of Channels | 16 mono input channels |
| Frequency Response | 20 Hz - 20 kHz (+0.5/-1 dB) |
| Total Harmonic Distortion | < 0.05% (20 Hz - 20 kHz) |
| Signal-to-Noise Ratio | > 95 dB (A-weighted) |
| Built-in Effects | 16 digital effect presets (reverb, delay, chorus, etc.) |
| Equalization per Channel | 3-band EQ (High, Mid, Low) |
| Aux Sends | 4 aux sends (pre/post fader selectable) |
| Stereo Aux Returns | 2 stereo returns |
| Main Outputs | XLR balanced main outputs |
| Phantom Power | +48V phantom power per channel group |
| Headphone Output | 1/4" TRS stereo headphone jack |
| USB Connectivity | USB 2.0 for recording/playback (2-in/2-out) |
| Power Supply | AC 100-240V, 50/60 Hz (external adapter) |
| Power Consumption | 40 W |
| Dimensions (W x D x H) | 500 mm x 400 mm x 150 mm |
| Weight | 8.5 kg |
| Housing Material | Steel chassis with aluminium front panel |
| Cleaning Instructions | Wipe with a dry, soft cloth. Do not use solvents or liquids. |
| Safety Certifications | CE, RoHS, FCC |
| Spare Parts and Service | Contact Korg authorized service centers for replacements and repairs. |
| Reparability | Service by qualified technician only. No user-serviceable parts inside. |
Frequently Asked Questions - SoundLink MW-1608 KORG
How do I connect a microphone to the SoundLink MW-1608?
Connect an XLR cable from your microphone to any mono input channel (channels 1-16). Press the +48V button if you use a condenser mic. Adjust the GAIN knob for proper level.
How do I apply built-in effects to a channel?
Press the EFFECTS button to access digital effects. Use the AUX 3/AUX 4 knobs to send signal from a channel to the effect processor. Then adjust the RETURN level to mix the effect.
Can I record audio via USB?
Yes, connect the mixer to your computer via USB (B-type). The mixer appears as a 2-in/2-out audio interface. Use your DAW software to record the main mix or a selected bus.
How do I reset the mixer to factory settings?
Turn off the mixer. Hold the EFFECTS and MAIN buttons while powering on. Continue holding until the LEDs flash. This resets all settings to default.
What is the correct way to power off the mixer?
Always turn down all volume faders to -∞ before powering off. Then switch off the POWER button to avoid loud pops.
Why is there no sound from the main output?
Check that the MAIN MIX fader is up, the STEREO output cables are connected, and the mixer is not muted. Ensure SOLO lights are off (press any lit solo button to clear).
How do I connect external effects (e.g., compressor)?
Use an AUX SEND (e.g., AUX 1) to feed the effect input. Return the effect signal to a STEREO RETURN channel. Use the RETURN level knob to blend the wet signal.
What headphones impedance is recommended?
The headphone output is designed for 32-300 ohm headphones. For best volume, use low-impedance headphones (32 ohms).
Can I use the mixer for live streaming?
Yes, connect the REC OUT (RCA) to your streaming device, or use USB for direct computer connection. Set USB ROUTING to MAIN MIX for streaming the full mix.
How do I clean the mixer safely?
Use a dry, lint-free cloth to wipe the surfaces. For stubborn dirt, slightly dampen the cloth with water (do not use alcohol or cleaners). Avoid moisture entering the controls.
User questions about SoundLink MW-1608 KORG
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Mixer in PDF format for free! Find your manual SoundLink MW-1608 - KORG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SoundLink MW-1608 by KORG.