Dynax 404Si - Camera KONICA MINOLTA - Free user manual and instructions
Find the device manual for free Dynax 404Si KONICA MINOLTA in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 35mm Film SLR Camera |
| Dimensions (approx.) | 150 x 100 x 70 mm |
| Weight (body only) | Approx. 500 g |
| Power Source | 2 x CR123A Lithium Batteries |
| Film Format | 35mm (135) |
| Lens Mount | Minolta A-Mount |
| Shutter Speeds | 30 s – 1/2000 s (Bulb) |
| Autofocus System | TTL Phase Detection (Single Area) |
| Metering Mode | Center-Weighted Average |
| Exposure Modes | Program, Aperture Priority, Shutter Priority, Manual |
| ISO Range | 25 – 5000 (DX coded or manual setting) |
| Built-in Flash | Pop-up, GN 12 (ISO 100, meters) |
| Film Advance | Built-in motor, single and continuous |
| Self-Timer | 10 seconds delay |
| Viewfinder | Fixed pentamirror, 0.8x magnification, 90% coverage |
| Focus Modes | Single-shot AF, Continuous AF, Manual |
| Maintenance | Keep camera and lens clean; store in dry place; replace batteries when weak |
| Safety Precautions | Avoid exposing to rain or moisture; do not open battery compartment when wet; keep away from children |
| Spare Parts & Repairability | Batteries, lens caps, and battery covers available online; repair service for internal components |
Frequently Asked Questions - Dynax 404Si KONICA MINOLTA
How do I load film into the Dynax 404Si?
Open the back cover by sliding the release switch. Insert the film cassette into the left chamber, pull the film leader across to the red line, close the back, and the camera will automatically advance to frame 1.
What batteries does the Dynax 404Si require?
It uses two CR123A lithium batteries. Insert them with correct polarity as indicated inside the battery compartment.
How do I set the ISO manually?
If using non-DX coded film, press the ISO button and turn the dial to adjust. The range is 25 to 5000.
Why is my Dynax 404Si not firing?
First, check that batteries are fresh and properly inserted. Ensure the lens is fully attached and the lock switch is in the 'On' position. The shutter may also lock if film is not loaded.
How do I enable the self-timer?
Press the self-timer button (usually marked with a timer icon). The LED will blink, and after 10 seconds the shutter fires.
Can I use manual lenses with the Dynax 404Si?
Yes, but only Minolta A-mount lenses with manual focus capability. Set the lens to M and the camera to Manual focus mode.
How do I rewind the film manually?
At the end of the roll, the camera auto-rewinds. If you need to rewind early, press the rewind button (arrow icon) on the back; the motor will reverse the film into the cassette.
What does the blinking '100' mean in the viewfinder?
It indicates a battery check. If the number blinks when you press the shutter halfway, the batteries are low and should be replaced.
How do I clean the lens?
Use a lens blower to remove dust, then a microfiber cloth with lens cleaning solution. Wipe gently in circular motion from center out.
Where can I find spare parts for the Dynax 404Si?
Batteries, lens caps, and battery covers are widely available online. For internal repairs, contact a camera repair shop familiar with Minolta SLRs.
User questions about Dynax 404Si KONICA MINOLTA
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Camera in PDF format for free! Find your manual Dynax 404Si - KONICA MINOLTA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Dynax 404Si by KONICA MINOLTA.
USER MANUAL Dynax 404Si KONICA MINOLTA
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : KONICA MINOLTA
Model : Dynax 404Si
Category : Camera