StarFlash III - Light projector MARTIN - Free user manual and instructions

Product Type	Strobe Light
Brand	Martin
Model	StarFlash III
Category	Effect Light
Dimensions (L x W x H)	330 x 203 x 152 mm
Weight	3.6 kg
Power Supply	AC 100-240V, 50/60Hz
Power Consumption	250 W
Light Source	Xenon flash tube
Flash Rate	1 - 14 flashes per second
Beam Angle	Approximately 120°
DMX Channels	1 or 2
Control Modes	DMX512, Master/Slave, Sound-activated, Standalone
Housing Material	Aluminum and steel
Cooling	Passive convection
Safety Certifications	CE, ETL
Operating Environment	Indoor use only (IP20)
Included Accessories	Mounting bracket, power cord
Maintenance	Clean lens with dry cloth
Reparability	Flash tube replaceable by qualified technician

Frequently Asked Questions - StarFlash III MARTIN

How do I connect the StarFlash III to a DMX controller?

Use a standard DMX512 cable with 5-pin XLR connectors. Connect the male end to the controller's output and the female end to the fixture's input. Set the DMX address via the DIP switches on the rear panel. Refer to the DMX chart in the manual for channel assignments.

Can I use the StarFlash III in sound-activated mode?

Yes, set the control mode selector to 'Sound' or 'Audio'. The fixture will respond to ambient sound levels via its built-in microphone. Adjust sensitivity with the rear knob if available.

What is the maximum flash rate of the StarFlash III?

The maximum flash rate is 14 flashes per second (14 Hz). This can be set via DMX or rear panel controls.

How do I clean the StarFlash III?

Disconnect power and allow to cool. Use a soft, dry cloth to wipe the housing and lens. Do not use solvents or abrasive cleaners. Clean the lens gently to avoid scratches.

What is the power consumption of the StarFlash III?

The power consumption is 250 watts at full output. Ensure the power supply circuit can handle this load. Use a dedicated circuit if multiple units are connected.

Is the StarFlash III suitable for outdoor use?

No, it is designed for indoor use only. It has an IP20 rating, meaning it is not protected against water or dust ingress. Protect from moisture and extreme temperatures.

Can I replace the flash tube myself?

The flash tube is replaceable but only by a qualified technician. Opening the unit without proper training can expose you to high voltage. Contact Martin service or an authorized dealer for replacement.

What is the beam angle of the StarFlash III?

The beam angle is approximately 120 degrees, providing wide coverage for strobe effects. The fresnel lens design spreads light evenly.

How do I set up Master/Slave mode?

Connect multiple units via DMX cables in a daisy chain. Set one unit as Master (mode switch to 'Master' or specific DMX address), and others as Slave (mode switch to 'Slave'). The Master controls all Slaves.

What safety precautions should I take when using the StarFlash III?

Always mount securely using the provided bracket. Do not block ventilation. Avoid staring directly into the flash at close range. Use a ground fault circuit interrupter (GFCI) if available. Disconnect power before servicing.

USER MANUAL StarFlash III MARTIN

Black Martin Starflash projector with labeled ports (no additional text or symbols visible)

© 1997-2001 Martin Professional A/S, Denmark.

All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark.

Printed in Denmark.

P/N 35000031, Rev. C

section 1 INTRODUCTION

Thank you for selecting the Martin Starflash III. The Starflash III is a powerful but compact effect which produces a variety of exciting effects depending on model. New for this version of the Starflash is improved music response circuitry.

Features

• 300 W halogen lamp
- Sharp, rotating, white or colored light beams
- Microprocessor control with accurate music response
• Thermo-switch for overheating protection
- Adjustable mounting bracket

Safety precautions

The Starflash III is NOT for domestic use. If you have any doubts about how to operate the fixture safely, please contact your Martin dealer for assistance.

• Read user manual before connecting or operating the fixture.
  • Install the fixture out of reach of accidental contact, at least 0.3 meters (12 inches) away from illuminated objects, and at least 0.1 meters (4 inches) from flammable materials. Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.
• Completely disconnect the fixture from electricity and allow to cool for 5 minutes before replacing the lamp or fuse.
• Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault protection. Ensure that the fixture is properly grounded (earthed).
• To reduce risk of fire and electrical shock, do NOT expose to rain or moisture.
• Replace the lamp when it becomes defective or worn out.
• Do not operate the fixture if the ambient temperature exceeds 40^ (104°F).
  • Refer all service to a Martin service technician.
• When suspending the fixture above ground level, verify that the structure can hold at least 10 times the weight of all installed devices.
• Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable.

section 2 SETUP AND OPERATION

The Starflash III includes a power cable, this user manual, and a mounting bracket. Before operating the fixture, you must insert a lamp (not included), install a plug on the power cord, and attach the mounting bracket.

Installing or replacing the lamp

Install only the lamp listed below for your model.

ModelLampVolts / WattsOutputAvg. LifeBase
EU Osram 64516 230 V / 300 W 7300 lm 50 h GX 6.35
US Philips 6874P (DRA) 120 V / 300 W 7700 lm 75 h GX 6.35
UK	Osram 64514 (M38)	240 V / 300 W	5200 lm	2000 h	GY 9.5

1. Unplug the fixture and allow it to cool for 5 minutes.
2. Remove the lamp-access thumbscrew on the top of the fixture.
3. If removing a bulb, gently pull it out of the socket.
4. Hold the new bulb in a clean cloth and insert the pins into the socket. Oils from your fingers shorten lamp life; if you do touch the bulb, clean it with a cloth wetted with denatured alcohol.
5. Replace the lamp-socket assembly and tighten the thumbscrew.
6. Sliding the lamp-socket forwards or backwards may improve performance. Unplug the fixture before making adjustments.

Installing a plug on the power cord

WARNING!

The fixture must be grounded (earthed).

The Starflash III may be delivered without a plug on the power cord. A 3-prong grounding-type plug must be installed. Following the manufacturer's instructions, connect the wires as follows.

1. Connect the BROWN wire to the LIVE pin.
2. Connect the BLUE wire to the NEUTRAL pin.
3. Connect the YELLOW/GREEN wire to the GROUND (EARTH) pin.

Connecting to AC power

IMPORTANT!

Do not attempt to dim the Starflash III: damage may occur to the electronic components.

1. Check to make sure the fixture's operating voltage and frequency, listed on the serial number label on the rear panel, match the AC voltage and frequency.
2. Plug the power cable into the socket on the back of the fixture and an AC outlet.

Note: Although the Starflash III cannot be dimmed, it may be switched on and off remotely using switch packs or the full on and full off levels on dimmer packs.

Installing the mounting bracket

1. Align the holes in the mounting bracket with the holes in the sides of the Starflash III.
2. Place the spacers between the case and the bracket and insert a knob in each side.
3. Tilt the Starflash III in the desired direction.
4. Tighten the thumbscrews.

Operating modes

To operate the Starflash III, apply power and set the mode switch on the rear panel to the “lamp on” or “flash” position.

Lamp On

In “lamp on” mode, the lamp stays on; rotation is sound activated and changes occasionally. If there is no sound, reflector rotation stops after 5 seconds.

Flash

In “flash” mode, both the lamp and rotation are sound activated. If there is no sound, the lamp turns off after 5 seconds. There is no difference between the 2 “flash” positions.

WARNING!

Unplug the fixture and allow to cool before proceeding.

Replacing the fuse

1. Unplug the power cord from the fixture.
2. Place the tip of a screwdriver in the slot on top of the fuse holder, located in the power cord socket, and pry open the holder.
3. Replace the fuse with one of the same rating. The rating is shown on the serial number label.
4. Replace the fuse holder and reconnect the power cord.

Troubleshooting

problem probable cause(s)suggested remedy

No light and the fan does not run.	No power to the fixture. •	Check connections.
	Blown fuse. • Replace fuse.
Fan runs but there is no light.	Sound too low to activate control circuit.	• Increase volume.
	Burned out lamp. • Install	new lamp.
	Fixture overheating.	• Allow to cool.• Improve air flow around the fixture.
Fuse blows repeatedly. E	Electrical malfunction. • Refer to service technician.

If the suggested remedies do not solve the problem, contact your Martin dealer for service.

appendix SPECIFICATIONS

Dimensions (with mounting bracket)

Length 277 mm (10.9 in)
Width....235 mm (9.25 in)
Height.....218 mm (8.6 in)
Weight 3.5 kg (7.7 lb)

Electrical

Power consumption ....325 W
Fuse, EU and UK models (220 - 240 V AC supply) ......F2 A / 250 V
Fuse, US model (100 - 130 V AC supply) ......F4 A / 250 V

Construction

Housing ....steel, aluminum
Finish ....electrostatic powder coating

Thermal

Surface temperature under normal conditions ....75° C (167° F)
Maximum operating environment temperature ....40°C (104°F)
Protection ...... thermo-switch

Accessories

Philips 6874P M38 halogen lamp (for UK model)....P/N 97000200
Osram 64514 DRA halogen lamp (for US model)....P/N 97000201
Osram 64516 halogen lamp (for EU model)....P/N 97000202
Martin DMX Switch Pack, 210-245 V P/N 90758200
Martin DMX Switch Pack, 100-130 V P/N 90758300