ProLiant DL120 G7 - Server HP - Free user manual and instructions
Find the device manual for free ProLiant DL120 G7 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rack-mounted Server |
| Form Factor | 1U |
| Processor | Intel Xeon E3-1200 v2 Series |
| Memory | Up to 32 GB DDR3 ECC Unbuffered (UDIMM) |
| Storage Bays | 4 x 3.5-inch SATA/SAS hot-plug |
| RAID Support | HP Smart Array B110i SATA RAID (0/1/10) |
| Network | 2 x Gigabit Ethernet (embedded) |
| Power Supply | 1 x 460W (non-hot-plug) or optional redundant |
| Dimensions (W x D x H) | 42.9 x 69.5 x 4.3 cm (16.9 x 27.4 x 1.7 in) |
| Weight | Approximately 12.5 kg (27.6 lbs) |
| Remote Management | HP iLO 3 (Integrated Lights-Out) |
| Operating Temperature | 10°C to 35°C (50°F to 95°F) |
| Storage Temperature | -10°C to 60°C (14°F to 140°F) |
| Power Consumption | Typical: 200W, Maximum: 350W |
| Expansion Slots | 1 x PCIe 3.0 x16 (low-profile) |
| Maintenance | Hot-plug fans, tool-less access, diagnostic LEDs |
| Security | Chassis intrusion switch, TPM support, secure boot |
| Spare Parts | HP ProLiant DL120 G7 spare kit (PSU, fans, trays) |
| Repairability | Customer self-repair (CSR) with HP support |
| General Information | Entry-level rack server for small businesses |
Frequently Asked Questions - ProLiant DL120 G7 HP
How do I access the BIOS or UEFI settings on the ProLiant DL120 G7?
Press F9 during POST to enter System Utilities. For UEFI settings, press F10.
What RAID levels are supported by the built-in controller?
The HP Smart Array B110i supports RAID 0, 1, and 10 with SATA drives.
Can I upgrade the memory to more than 32 GB?
No, the maximum is 32 GB using 8 GB DDR3 UDIMMs. It does not support RDIMMs.
How to configure iLO 3 for remote management?
During BIOS, press F8 to enter iLO configuration. Set an IP address, enable DHCP, and create login credentials.
What type of power supply does the DL120 G7 use?
It uses a non-hot-plug 460W AC power supply, with an optional redundancy kit.
How to replace a failed hard drive?
The drives are hot-plug. Press the release button, remove the failed drive, insert a new one, and rebuild via RAID controller.
What is the supported operating system list?
Supports Windows Server 2008/2012, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, VMware ESXi, and others.
How do I reset the iLO password?
Hold the reset button on the system board for 10 seconds while power is on, or use the iLO reset utility.
What are the audible beep codes indicating?
One beep: memory error. Two beeps: system board error. Three beeps: processor error. Refer to the manual for full codes.
Can I install a PCIe graphics card in this server?
Yes, there is one PCIe 3.0 x16 low-profile slot. Ensure the card does not exceed power limits and fits in a 1U chassis.
User questions about ProLiant DL120 G7 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual ProLiant DL120 G7 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ProLiant DL120 G7 by HP.