AMP1 - Receiver NAD - Free user manual and instructions
Find the device manual for free AMP1 NAD in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Brand | NAD |
| Model | AMP1 |
| Power Output | 50 watts per channel into 8 ohms |
| Frequency Response | 20 Hz – 20 kHz (±0.5 dB) |
| Total Harmonic Distortion | <0.08% |
| Inputs | 3x RCA line, 1x phono (MM), 1x optical, 1x coaxial |
| Outputs | Speaker terminals (A/B), pre-out, headphone jack |
| Tuner Bands | AM, FM (with RDS) |
| Dimensions (W x H x D) | 435 x 100 x 350 mm |
| Weight | 7.5 kg |
| Power Supply | AC 120V/240V, 50/60 Hz |
| Power Consumption | 250 W (max), <1 W standby |
| Remote Control | Included (RC-1001) |
| Speaker Impedance | 4–16 ohms |
| Signal-to-Noise Ratio | 88 dB (line input) |
| Main Functions | AM/FM radio, amplifier, input selection, volume control, tone controls |
| Maintenance & Cleaning | Wipe with soft dry cloth; do not use liquids or solvents. |
| Safety Instructions | Do not open chassis; disconnect power before cleaning; avoid moisture. |
| Spare Parts & Repairability | Contact NAD customer support for authorized service. |
| General Information | Designed for home audio systems; supports multiple sources. |
Frequently Asked Questions - AMP1 NAD
How do I connect my turntable to the NAD AMP1?
Connect your turntable to the Phono input. Ensure it has a moving magnet (MM) cartridge. If your turntable has a built-in preamp, use the Line input instead.
Why is there no sound from my speakers?
Check that the speakers are connected to the correct terminals and the Speaker A/B switch is on. Also verify the volume is not at minimum and the source is selected properly.
How do I set the radio stations?
Press Tuner to select AM or FM. Use the Tuning knob to find a station, then press and hold a Preset button to save it.
What is the maximum power output?
The NAD AMP1 delivers 50 watts per channel into 8 ohms, both channels driven.
Can I use headphones with the AMP1?
Yes, there is a Headphone jack on the front panel. Plugging in headphones mutes the speakers automatically.
How do I reset the AMP1 to factory settings?
Turn off the unit, then press and hold the Power button for 10 seconds. Release when the display shows 'RESET'.
The remote control is not working. What should I do?
Replace the batteries with two new AAA batteries. Ensure there are no obstacles between the remote and the receiver's sensor.
What is the impedance range for speakers?
The AMP1 supports speakers with an impedance between 4 and 16 ohms.
How do I clean the receiver?
Use a soft, dry cloth to wipe the exterior. Do not use any liquids, sprays, or abrasive cleaners.
Where can I find spare parts or service?
Contact NAD customer support or visit the official NAD website for authorized service centers.
User questions about AMP1 NAD
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual AMP1 - NAD and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AMP1 by NAD.
USER MANUAL AMP1 NAD
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : NAD
Model : AMP1
Category : Receiver