840 PRO - SSD SAMSUNG - Free user manual and instructions

Product Type	Internal Solid State Drive (SSD)
Capacity	128 GB / 256 GB / 512 GB / 1 TB (depending on model)
Form Factor	2.5-inch
Interface	SATA III (6 Gb/s), backward compatible with SATA II (3 Gb/s)
Sequential Read Speed	Up to 540 MB/s
Sequential Write Speed	Up to 520 MB/s
NAND Flash Type	21nm MLC (Multi-Level Cell)
Controller	Samsung MDX (Cortex-R4 based)
Dimensions	100.0 x 69.85 x 7.0 mm
Weight	Approximately 50 g
Power Consumption (Active)	0.1 W (typical) – 0.5 W (max)
Power Consumption (Idle)	0.045 W (typical)
Operating Temperature	0°C to 70°C
Shock Resistance	1500 G / 0.5 ms (max)
MTBF	2,000,000 hours
Warranty	5 years limited
Special Features	Samsung Magician software, RAPID mode, AES 256-bit encryption, TRIM support

Frequently Asked Questions - 840 PRO SAMSUNG

How do I install the Samsung 840 PRO SSD in my desktop?

First, power off your computer and disconnect all cables. Open the case, locate a 2.5-inch drive bay or use a mounting bracket. Connect the SATA data cable from the SSD to your motherboard and attach the power cable from your PSU. Secure the drive, close the case, and boot up. Initialize the SSD via Disk Management (Windows) or Disk Utility (Mac).

Is the Samsung 840 PRO compatible with SATA II (3 Gb/s) ports?

Yes, the 840 PRO is backward compatible with SATA II. However, performance will be limited to SATA II speeds (up to ~280 MB/s sequential). For best performance, use a SATA III (6 Gb/s) port.

Does the 840 PRO support the TRIM command?

Yes, the Samsung 840 PRO fully supports the TRIM command, which helps maintain performance over time by allowing the OS to inform the SSD which data blocks are no longer in use. Ensure TRIM is enabled in your OS (it is by default in Windows 7 and later).

How do I update the firmware on my Samsung 840 PRO?

Download the latest firmware from Samsung's website and use the Samsung Magician software to update. Alternatively, you can create a bootable USB with the firmware update ISO. Always back up your data before updating firmware.

What is the lifespan of the Samsung 840 PRO?

The 840 PRO has a rated endurance of 73 TBW (Total Bytes Written) for the 128GB model, scaling up to 365 TBW for the 1TB model. With typical usage, it should last many years. The SSD also has a 5-year warranty.

Can I use the Samsung 840 PRO to speed up my laptop?

Absolutely. Replacing your laptop's HDD with the 840 PRO will significantly reduce boot times, application load times, and overall system responsiveness. Ensure the laptop has a 2.5-inch SATA bay.

How do I clone my old HDD to the Samsung 840 PRO?

You can use Samsung's Data Migration software (available via Samsung Magician) or third-party tools like Acronis True Image. Connect both drives, run the cloning software, select source and target, and start the process. After cloning, swap the drives and boot.

Can I use the Samsung 840 PRO as a cache drive with Intel Smart Response Technology?

Yes, the 840 PRO can be used as a cache drive for SRT. However, it is more efficient and cost-effective to use a smaller SSD for caching. For optimal performance, consider using the SSD as the primary boot drive instead.

What is the difference between Samsung 840 PRO and 840 EVO?

The 840 PRO uses faster MLC NAND and a more powerful controller (MDX) compared to the 840 EVO's TLC NAND and MEX controller. The PRO offers higher sustained write speeds and better endurance, while the EVO is more affordable for consumer use.

My computer does not detect the Samsung 840 PRO. What should I do?

Check that the SATA data and power cables are securely connected. Try a different SATA port or cable. Enter the BIOS/UEFI and ensure the SATA controller is set to AHCI mode. If still not detected, test the SSD in another computer to rule out drive failure.

USER MANUAL 840 PRO SAMSUNG

Samsung SSD Self-Install Photo Guide for desktop computers

© 2013 Samsung Electronics Co.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

01

Bracket

Package (installation program & manual CD instruction manual, warranty)

SSD

mounting spacer

SATA cable

screws

SATA to USB connector

stickers

SSD Self-Install Photo Guide

for desktop computers

Carefully open the SSD box.

Make sure that there are no missing components!

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Remove the CD from the black document pouch, and insert it into the CD-ROM drive.

You can also download the guide at www.samsung.com/samsungssd.

(See next page)

Checking the Produ

Installing the Progr

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

You can also download the program at the official Samsung SSD homepage.

You can also download the guide at www.samsung.com/samsungssd. (SSD firmware, Magician software, Samsung Data Migration software)

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Install the Magician program.

*Run the CD, then click the setup file in the Magician Software folder to install the program.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Install the Data Migration program.

Using Data Migration migrates all of the user's data including the OS.

This means re-installation of the OS is not necessary.

* Run the CD, then click the setup file in the Magician Software folder to install the program.

SSD Self-Install Photo Guide

for desktop computers

Run the Data Migration program, and then connect the SSD to the computer.

1. On the main screen, click 'Start' to run the Data Migration program.

SSD Self-Install Photo Guide for desktop computers

Connect the SSD to the computer.

1. Connect the SSD to the desktop computer using the SATA to USB connector.

Checking the Product

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

08

SSD Self-Install Photo Guide for desktop computers

Run the Data Migration program, and make sure to the SSD is detected in the program.

1. The Data Migration program will automatically detect the SSD.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Click the 'Start Migration' button to start Data Migration.

* Data Migration migrates the data and the operating system (Windows) installed on the computer you are using to the SSD you have purchased.
* After data migration is complete, turn off the computer and then disconnect the SSD from the USB connector.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Open the cover of your computer.

* The details of how to open the cover differ between computer models. Refer to the service manual for your computer to open the cover safely.
* You need to open the cover on the opposite side to remove the HDD. This is described in the next step.

Checking

the Product

Installing

the Program

Data

Migration

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Disconnect all the cables that are connected to the original HDD (or existing SSD) in your computer.

The cables that have been disconnected from the original HDD need to be reconnected to your new SSD. It is recommended that you mark these cables in some way so that they are not confused with other cables.

SSD Self-Install Photo Guide for desktop computers

Remove the HDD by unfastening the screws holding the HDD in the drive bay.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Attach the bracket to the SSD.

* The bracket is sold separately. (However, a bracket is included in the Desktop Kit and All-in-One Kit.)
* The bracket may not be necessary, depending on the design of your computer.
* Use four screws to fasten it securely in place.

Checking the Product

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Attach the bracket to the SSD.

* The bracket is sold separately. (However, a bracket is included in the Desktop Kit and All-in-One Kit.)
* The bracket may not be necessary, depending on the design of your computer.
* Use four screws to fasten it securely in place.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Insert the SSD, fitted with the bracket, into the location of the original HDD (usually SATA port #0), and secure it in place.

The HDD is usually mounted in SATA port #0, because booting starts at the lowest-numbered SATA port and then proceeds sequentially. (Port #0, port #1, port #2, and so on.)

Therefore, you need to mount your new SSD in SATA port #0 (vacated by the existing HDD), which is the lowest-numbered SATA port.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Insert the SSD, fitted with the bracket, into the location of the original HDD (usually SATA port #0), and secure it in place.

The HDD is usually mounted in SATA port #0, because booting starts at the lowest-numbered SATA port and then proceeds sequentially. (Port #0, port #1, port #2, and so on.)

Therefore, you need to mount your new SSD in SATA port #0 (vacated by the existing HDD), which is the lowest-numbered SATA port.

SSD Self-Install Photo Guide for desktop computers

Connect the cables that have been disconnected from the existing HDD to your new SSD.

SSD Self-Install Photo Guide for desktop computers

Connect the cables that have been disconnected from the existing HDD to your new SSD.

SSD Self-Install Photo Guide for desktop computers

Connect the existing HDD to the port with the next lowest number.

For example, if the SSD is connected to port #0, then connect the HDD to port #1.

SSD Self-Install Photo Guide for desktop computers

Connect the existing HDD to the port with the next lowest number.

For example, if the SSD is connected to port #0, then connect the HDD to port #1.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Connect the SATA cable and the power cable to the reinstalled HDD.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Connect the SATA cable and the power cable to the reinstalled HDD.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Reattach the side covers to the computer.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Reboot the computer, and immediately enter BIOS setup.

Entering the BIOS setup may be done differently depending on mainboard and/or computer manufacturer.

Usually, you can enter BIOS setup by pressing the Delete key or the F2 key before the boot sequence proceeds to Windows.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Change IDE mode to AHCI mode.

* AHCI mode is usually found under advanced options.
* Some mainboards may not support AHCI.
(In this case you should obtain a separate driver from the manufacturer of the mainboard or the OS to maximize the performance of the SSD.)
* Once installation is completed, install necessary drivers.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

When you boot up the computer, Windows will detect the new SSD automatically, and a message will advise you reboot the computer.

* Once the desktop computer detects the newly mounted SSD, a message will advise you reboot the computer. This is normal, and you should reboot the computer.

SSD Self-Install Photo Guide for desktop computers

After rebooting, run the Magician program to verify that the SSD has been detected correctly.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

23

SSD Self-Install Photo Guide

for desktop computers

Check the AHCI mode and SATA interface settings.

* If AHCI mode is enabled and the SSD is connected to SATA 3 as shown in the photo, run OS Optimization setup (in the left menu).
* The SSD performs optimally when using AHCI mode and SATA 3.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

If you are using SATA 2, check whether your mainboard supports SATA 3.

* If SATA 3 is supported, turn off your computer and connect the SSD using SATA 3.
* If SATA 3 is not supported, proceed to the next step.

For more information, please contact the manufacturer of your mainboard.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

After setup has completed, check OS optimization.

* Run performance benchmark and performance optimization from the left menu to ensure optimal performance.
* For more information, please refer to 'Help', located at the lower right corner.

SSD Self-Install Photo Guide for desktop computers

Place the SSD sticker in a prominent location.

The installation and optimization of the SSD is now complete.

SAMSUNG

Thank you.

Samsung SSD Self Installation Photo Guide for desktop computers (reinstalling Windows)

© 2013 Samsung Electronics Co.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Carefully open the SSD box.

Make sure that there are no missing components!

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Open the cover of your computer.

* The details of how to open the cover differ between computer models. Refer to the service manual for your computer to open the cover safely.
* You need to open the cover on the opposite side to remove the HDD. This is described in the next step.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Disconnect all the cables that are connected to the original HDD (or existing SSD) in your computer.

The cables that have been disconnected from the original HDD need to be reconnected to your new SSD. It is recommended that you mark these cables in some way so that they are not confused with other cables.

SSD Self-Install Photo Guide for desktop computers

Remove the HDD by unfastening the screws holding the HDD in the drive bay.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Attach the bracket to the SSD.

* The bracket is sold separately. (However, a bracket is included in the Desktop Kit and Allin-One Kit.)
* The bracket may not be necessary, depending on the design of your computer.
* Use four screws to fasten it securely in place.

SSD Self-Install Photo Guide for desktop computers

Attach the bracket to the SSD.

* The bracket is sold separately. (However, a bracket is included in the Desktop Kit and Allin-One Kit.)
* The bracket may not be necessary, depending on the design of your computer.
* Use four screws to fasten it securely in place.

SSD Self-Install Photo Guide for desktop computers

Insert the SSD, fitted with the bracket, into the location of the original HDD. (usually SATA port #0), and secure it in place.

The HDD is usually mounted in SATA port #0, because booting starts at the lowest-numbered SATA port and then proceeds sequentially. (Port #0, port #1, port #2, and so on.)

Therefore, you need to mount your new SSD in SATA port #0 (vacated by the existing HDD), which is the lowest-numbered SATA port.

SSD Self-Install Photo Guide for desktop computers

Insert the SSD, fitted with the bracket, into the location of the original HDD. (usually SATA port #0), and secure it in place.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Connect the cables that have been disconnected from the existing HDD to your new SSD.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Connect the cables that have been disconnected from the existing HDD to your new SSD.

SSD Self-Install Photo Guide for desktop computers

Connect the existing HDD to the port with the next lowest number.

For example, if the SSD is connected to port #0, then connect the HDD to port #1.

SSD Self-Install Photo Guide for desktop computers

Connect the existing HDD to the port with the next lowest number.

For example, if the SSD is connected to port #0, then connect the HDD to port #1.

SSD Self-Install Photo Guide for desktop computers

Connect the SATA cable and the power cable to the reinstalled HDD.

SSD Self-Install Photo Guide for desktop computers

Connect the SATA cable and the power cable to the reinstalled HDD.

SSD Self-Install Photo Guide for desktop computers

Reattach the side covers to the computer.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

SSD Self-Install Photo Guide

for desktop computers

Turn on the computer, and install Windows.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

12

SSD Self-Install Photo Guide

for desktop computers

Reboot the computer, and immediately enter BIOS setup.

Entering the BIOS setup may be done differently depending on mainboard and/or computer manufacturer.

Usually, you can enter BIOS setup by pressing the Delete key or the F2 key before the boot sequence proceeds to Windows.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Change IDE mode to AHCI mode.

* AHCI mode is usually found under advanced options.
* Some mainboards may not support AHCI.
(In this case you should obtain a separate driver from the manufacturer of the mainboard or the OS to maximize the performance of the SSD.)
* Once installation is completed, install necessary drivers.

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

Install the Magician program using the CD provided.

* Run the CD located in the black document pouch, then click the setup file in the Magician Software folder to install the program
* You can also download the program and the guide at www.samsung.com/samsungssd

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

You can also download the program at the official Samsung SSD homepage.

You can also download the program and the guide at www.samsung.com/samsungssd (SSD firmware, Magician software, Samsung Data Migration software)

Checking the Produ

Installing the Program

Data Migration

Mounting the SSD

Checking SSD Mounting

SSD Self-Install Photo Guide for desktop computers

After running the Magician program, verify that the SSD has been detected correctly.

Checking

the Product

Installing

the Program

Data

Migration

Mounting

the SSD

Checking

SSD Mounting

17

SSD Self-Install Photo Guide

for desktop computers

Check the AHCI mode and SATA interface settings.

* If AHCI mode is enabled and the SSD is connected to SATA 3 as shown in the photo, run OS Optimization setup (in the left menu).
* The SSD performs optimally when using AHCI mode and SATA 3.

SSD Self-Install Photo Guide for desktop computers

If you are using SATA 2, check whether your mainboard supports SATA 3.

* If SATA 3 is supported, turn off your computer and connect the SSD using SATA 3.
* If SATA 3 is not supported, proceed to the next step.

For more information, please contact the manufacturer of your mainboard.

SSD Self-Install Photo Guide for desktop computers

After setup has completed, check OS optimization.

* Run performance benchmark and performance optimization from the left menu to ensure optimal performance.
* For more information, please refer to 'Help', located at the lower right corner.

SSD Self-Install Photo Guide for desktop computers

Place the SSD sticker in a prominent location.

* The installation and optimization of the SSD is now complete.

SAMSUNG

Thank you.