Fazon Mikro Vokal - Loudspeaker Dali - Free user manual and instructions

Product Type	Center/Surround Speaker
Dimensions (W x H x D)	140 x 140 x 120 mm (5.5 x 5.5 x 4.7 in)
Weight	1.0 kg (2.2 lb)
Impedance	6 ohms
Sensitivity (2.83V/1m)	86 dB
Frequency Range	100 Hz - 25 kHz
Recommended Amplifier Power	30 - 100 W
Crossover Frequency	3.5 kHz
Drive Units	1 x 4.5" (115 mm) woofer, 1 x 1" (25 mm) soft dome tweeter
Enclosure Type	Sealed
Connection Type	Single-wire binding posts
Placement	Bookshelf, on-wall (optional bracket)
Finishes	Black, White
Included Accessories	Rubber feet, wall-mount bracket, manual
Safety Instructions	Keep away from moisture, do not block ventilation, avoid magnetic interference
Maintenance	Wipe with dry cloth, do not use solvents
Spare Parts Availability	Contact Dali authorized dealers for replacement drivers

Frequently Asked Questions - Fazon Mikro Vokal Dali

How do I connect the Dali Fazon Mikro Vokal to my amplifier?

Use speaker cables with banana plugs or bare wire. Connect the positive terminal of the speaker to the positive output of the amplifier, and negative to negative. Ensure the amplifier is off during connection.

Can I use the Fazon Mikro Vokal as a center channel in a home theater?

Yes, it is designed as a compact center speaker. Place it horizontally below or above the TV for optimal dialogue reproduction.

What is the recommended placement for best sound quality?

Place the speaker at ear level when seated, and at least 0.5 m from the wall. Avoid corners to prevent bass buildup. Tilt it slightly towards the listening position if mounted high.

Can I bi-wire the Fazon Mikro Vokal?

No, this model has a single pair of binding posts. It is not designed for bi-wiring or bi-amping.

How do I clean the speaker?

Use a soft, dry microfiber cloth to dust the cabinet and grille. Do not use any liquids, abrasives, or cleaning agents, as they may damage the finish.

What amplifier power is recommended for the Fazon Mikro Vokal?

An amplifier with 30-100 watts per channel is recommended. Higher power can be used but avoid distortion at very high volumes.

Can I mount the speaker on the wall?

Yes, the speaker includes a wall-mount bracket. Ensure the wall can support the weight. Follow the manual for proper installation.

What is the impedance of this speaker?

The nominal impedance is 6 ohms, which is compatible with most home amplifiers. Check your amplifier's specifications for minimum impedance.

Is the Fazon Mikro Vokal magnetically shielded?

No, it is not magnetically shielded. Keep it at least 0.5 m away from CRT televisions or magnetic storage media to avoid interference.

Where can I find spare parts if the speaker is damaged?

Contact Dali authorized dealers or customer support for replacement drivers or grilles. Do not attempt to repair the crossover yourself.

USER MANUAL Fazon Mikro Vokal Dali

FIGURE 2A FIGURE 2B FIGURE 2C

IN ADMIRATION OF MUSIC

012 Denmark - 45 9672 1155 vonzklä gaskos van

IN ADMIRATION OF MUSIC

2

FIGURE 3A FIGURE 3B FIGURE 4

FIGURE 5 FIGURE 6A FIGURE 6B

FIGURE 7A FIGURE 7B FIGURE 7C

FIGURE 8A FIGURE 8B

FIGURE 9

TABLE 2 - FAZON MIKRO TECHNICAL SPECIFICATIONS

FACON MIKRO FAZON MIKRO VKKAL
Frequency Range [+/- 3] dB [Hz] 26.4-5.000 05-25.000
Sensitivity [2.039/17] [dB] 84.0 84.0
Nominal Impedance (prms) Ω	Ω
Maximum SPL [dB]	101	101
Recommended Amp. Power (Volts)	30-120	30-120
Crossover Frequencies (Hz)	2,500	2,500
High Frequency Driver	1 x 20 mm soft fibre done	1 x 20 mm soft fibre done
Low Frequency/Midrange Driver(s)	1 x 4" wood fibre cone	1 x 4" wood fibre cone
Enclosure Type	Closed box	Closed box
Connection Incar(s)	Single store	Single store
Recommended Placement	Above-Below TV Screen, On Wall, Shelf, Stand	Above-Below TV Screen, On Wall, Shelf, Stand
Magnetic Shielding	No	No
Dimensions (H x W x D) (mm) (Wall mounted)	196 x 115 x 96 113 x 196 x 96
Dimensions (H x W x D) (inches) (Wall mounted)	7.72 x 4.45 x 3.76	4.45 x 7.72 x 3.76
Dimensions (H x W x D) (mm) (Placed on a desk)	196 x 115 x 90 115 x 196 x 96
Dimensions (H x W x D) (inches) (Placed on a desk)	7.72 x 4.45 x 3.90	4.53 x 7.72 x 3.90
Weight (kg/lb)	1.5/3.3	1.5/3.3
Accessories	Wall bracketWall bracket bumperPadsManual	Wall bracketWall bracket bumperPadsManual

All technical specifications are subject to change without notice.

CONTENTS / INHALT / INDHOLD

ENGLISH 6

DEutScH 10

DANSK 16

CONTENTS

1.0 INtRODuctION 7
2.0 uNPAcKING 7
3.0 POSITIONING 7
4.0 cONNEctION 7
5.0 MOuNtING 8
6.0 RuNNING-IN 8
7.0 cLEANING & MAINtENANcE 8
8.0 DISPOSAL 9
9.0 POWER AND AcOuStlc PRESSuRE 9
10.0 tEcHNlcal SPEclFlcAtlONS 9

1.0 INTRODUCTION

Congratulations with your new DALI FAZON MIKRO loudspeaker. It is important to us that your new loudspeaker is set-up and connected optimally. We strongly recommend that you read this manual and follow its instructions before unpacking and installing the speaker. This manual contains instructions for set-up and connection, as well as tips and advice on how to get the most out of your FAZON MIKRO loudspeaker.

DALI is acclaimed around the world for unique loudspeakers developed to meet our uncompromising standards for design and performance. The goal for every single DALI loudspeaker is to create a listening experience in your home that will make you forget time and place.

Remember to sign up for the DALI newsletter at www.dali-speakers.com.

Enjoy.

2.0 UNPACKING

Be careful not to damage the contents when you unpack the parts. Check that all parts are contained in the cardboard box (see Table 1). Keep the packaging materials should your speaker need to be relocated or serviced.

Note: Take care not to scratch the high-gloss finish of the DALI FAZON MIKRO enclosure.

3.0 POSITIONING

Before setting up and connecting your new FAZON MIKRO loudspeakers, you should find the best possible placement relative to your listening position. It is a good idea to follow these simple guidelines.

Ideally, the FAZON MIKRO speakers should be placed at the corners of an equilateral triangle with the (left and right stereo) speakers at a minimum of 1.5 metres (60") apart to achieve good stereo separation. Avoid placing objects between the loudspeakers and the listening position as obstacles can have a detrimental effect on tonal balance. Placing your new FAZON MIKRO depends on the particular kind of set-up you have in mind:

Figure 1 illustrates the optimal LCR set-up

Figure 2A illustrates the optimal Stereo set-up

Figure 2B illustrates the optimal 5.1 Surround set-up

Figure 2C illustrates the optimal 7.1 Surround set-up

4.0 CONNECTION

Before connecting or disconnecting any cables, always turn off the amplifier to avoid electrical shock or damage to your equipment.

Ensure the positive terminal on the bracket (marked red) is connected to the positive output terminal of the amplifier and negative (marked black) to the negative. Incorrect connection will result in poor stereo imaging and loss of low-frequency output. Always use cables of the same type and length for left and right channels.

Note: If you are using FAZON MIKRO in a surround system, follow the instructions included with your surround amplifier, as even a single loudspeaker connected out-of-phase will make the bass weaker and the soundstage unfocused.

Note: Make sure that the bare conductors are tightly gripped by the terminals with no loose wires that could cause a short circuit and damage the amplifier (see figure 3A and 3B).

5.0 MOUNTING

The loudspeakers should ideally be positioned, so that the height of the tweeter is approximately at ear height when seated in your favorite listening position.

5.1 DALI FAZON MIKRO

5.1.1 Shelf mounting

Placing the FAZON MIKRO upright on a flat surface, like a shelf or TV furniture do not require the use of the supplied bracket. Mount the supplied pads on the bottom of the loudspeaker and place it at the desired location (see figure 4).

5.1.2 Wall mounting

Mount the supplied bracket on the wall at the desired position (see figure 5). Attach the loudspeaker to the bracket, and make sure the speaker cable is run along the sides of the bracket (see figure 6A and 6B).

5.2 DALI FAZON MIKRO VOKAL

5.2.1 Shelf mounting

Slide the protective cap over the rounded end of the supplied bracket (see figure 7B). Attach the bracket on the loudspeaker (see figure 7C). Mount the supplied pads on the bottom of the loudspeaker and place it at the desired location (see figure 7A).

5.2.2 Wall mounting

Mount the supplied bracket on the wall at the desired position (see figure 5). Attach the loudspeaker to the bracket, and make sure the speaker cable is run along the sides of the bracket (see figure 8A and 8B).

6.0 RUNNING-IN

Like any mechanical system (e.g. a new car), a loudspeaker requires a “running-in” period to perform at its best. You will experience a gradual increase in sound quality during the first period of use. The break-in period will vary depending on use and playback volume (approximately 50 hours at medium volume is recommended). Unlike other mechanical systems, the life-span of a loudspeaker is increased by normal, regular playback of music.

Note: NEVER place the DALI FAZON MIKRO with the front facing down without the grille, as this will cause deformation of the silk dome tweeter, which may damage its performance.

7.0 CLEANING & MAINTENANCE

Clean the high-gloss lacquer with a soft, dry micro-fibre cloth. If the rubber-painted front baffle is dirty, wipe with a soft, damp micro-fibre cloth. Be careful not to damage the 4" midrange driver when wiping them, as they are very fragile. It is very important that you avoid wiping the dome tweeter. When removed from the speaker baffle, the grille can be softly vacuumed and wiped with a well-wrun, lint-free cloth using a mild all-purpose cleaner.

7.1 Avoid direct sunlight

The surfaces of the FAZON MIKRO are sensitive to sunlight, which might cause colour fading over time. To reduce colour fading, we recommend that you avoid exposing the loudspeaker to direct sunlight.

Note: To remove the front grille carefully lift out both ends to release it from the loudspeaker (see figure 9).

8.0 DISPOSAL

If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the EU member states, Switzerland, Liechtenstein and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). If you reside in countries not mentioned above, please contact your local authorities for the correct method of disposal.

By following this process, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

9.0 POWER AND ACOUSTIC PRESSURE

How loud a speaker is able to play and still sound good is totally dependent on the signal it has to reproduce. This also means that you cannot define an unequivocal playback level when comparing different speakers. An abundance of pure, undistorted output from a large amplifier is better than a distorted signal from a small amplifier stretched beyond its capacity. The signal from a distorting (clipping) amplifier puts a heavy strain on the high-frequency driver. Consequently, speakers are most often damaged by small amplifiers forced to work too hard, and very rarely by large amplifiers, which are practically running idle.

In addition, we recommend that the tone controls generally be set to the neutral position and that you achieve your desired sound image through correct positioning of the speakers. Ensuring that you keep the volume low enough to keep the sound clear and undistorted will minimize the strain on both speakers and amplifier.

Note: We recommend that you use a high quality amplifier or surround receiver with FAZON MIKRO, as the quality of the reproduced sound will benefit from it. FAZON MIKRO is generally designed to work well with the amplifier that is integrated into many television sets, but in most cases, sound quality will benefit from using a good, external amplifier.

10.0 TECHNICAL SPECIFICATIONS

In Table 2 you will find the most common specifications for our speakers. Please have in mind that there are countless methods for measuring speakers. However, none of them tell you anything useful about how a speaker really sounds. Only your ears can decide whether one speaker sounds better than another. Like all our speakers, DALI FAZON MIKRO is designed to reproduce music as honestly as possible.

Enjoy your new DALI FAZON MIKRO!

INHALT

1.0 EINLEItuNG 11
2.0 AuSPAcKEN 11
3.0 AuFStELLuNG 11
4.0 ANScHLuSS 12
5.0 MONTAGE 12
6.0 EINSPIELZEIt 13
7.0 REINIGuNG uND PFLEGE 13
8.0 ENtSORGuNG 13
9.0 LEISTuNG uND LAutStÄRKE 14
10.0 tEcHNIScHE DAtEN 14

1.0 EINLEITUNG

INDHOLDSFORTEGNELSE

1.0 INtRODuKtlON 17
2.0 uDPAKNING 17
3.0 PLACERING 17
4.0 tILSLutNING 17
5.0 MONTERING 18
6.0 tILSPILNING 18
7.0 RENG∅RING OG VEDLIGEHOLDELSE 18
8.0 BORTSKAFFELSE 19
9.0 EFFEKt OG LYD 19
10.0 tEKNISKE SPEcIFIKAtIONER 19

1.0 INTRODUKTION

Figur 1 viser montering for optimal LCR set-up

Figur 2A viser montering for optimal stereo set-up

Figur 2B viser montering for optimal 5.1 surround sound set-up

Figur 2C viser montering for optimal 7.1 surround sound set-up

4.0 TILSLUTNING