CP70 CP09 - Vacuum Cleaner HOOVER - Free user manual and instructions

Product Type	Vacuum Cleaner
Brand	Hoover
Model	CP70 CP09
Vacuum Type	Bagged Canister Vacuum Cleaner
Power	700 W
Bag Capacity	3.5 L
Operating Radius	8 m
Filtration	Washable Permanent Filter
Included Accessories	Crevice tool, brush tool, upholstery tool
Noise Level	78 dB(A)
Cable Length	6 m
Weight	4.5 kg
Dimensions (L x W x H)	28 x 22 x 30 cm
Power Supply	Mains, 220-240 V
Power Adjustment	Electronic Speed Control
Bag System	Automatic Shut-off System
Filter Maintenance	Wash with warm water every 3 months
Bag Replacement	When indicator is red or at least every 2 months
Spare Parts Available	Bags, filters, tools
Repairability	Repairability index: 6.5/10
Warranty	2 years
Country of Manufacture	China

Frequently Asked Questions - CP70 CP09 HOOVER

How do I change the bag on the Hoover CP70 CP09 vacuum cleaner?

Open the front flap, remove the full bag by pulling it upwards. Insert a new bag and push until it clicks. Close the flap. Use only original Hoover bags.

How do I clean the filter on the Hoover CP70 CP09?

The permanent filter can be cleaned with warm water. Remove it, rinse under the tap, let it dry completely for 24 hours before reinstalling. Do not use detergent.

Why does the Hoover CP70 CP09 overheat?

Normal heat may occur during prolonged use. If overheating is excessive, check that the bag is not full, the filter is not blocked, and the hoses are not clogged. Let it cool for 30 minutes.

What type of bag should I use for the Hoover CP70 CP09?

Use Hoover Microsan or Hygienic bags. The compatible bag model is the Hoover type C bag (reference 19007820).

How to resolve loss of suction on the Hoover CP70 CP09?

Check if the bag is full, the filter is clogged, the hose is punctured or blocked, and that the speed control is set to maximum power. Clean the filter if necessary.

How to replace the filter on the Hoover CP70 CP09?

The permanent filter is washable. If damaged, order a replacement Hoover filter (ref. 19007880). To replace it, open the bag compartment, remove the old filter, insert the new one.

What is the motor power of the Hoover CP70 CP09?

The motor has a power of 700 W. This allows efficient suction for all floor types.

Is the Hoover CP70 CP09 suitable for pets?

Yes, with the brush tool and permanent filter, it can pick up pet hair. Use the upholstery tool for sofas. It is recommended to clean the filter more frequently.

How to maintain the hose of the Hoover CP70 CP09?

Regularly check that the hose is not kinked or blocked. To clean it, use a long flexible object or rinse with clean water. Dry it before reinstalling.

Where to buy spare parts for the Hoover CP70 CP09?

Spare parts (bags, filters, tools) are available on the Hoover.fr website, in specialized stores, or on platforms like Amazon. Use the references mentioned in the manual.

USER MANUAL CP70 CP09 HOOVER

H: 64.980

2018

1. 1 January 2017

1 October 2015

GB

IMPORTANT SAFETY REMINDERS

This cleaner should only be used for domestic cleaning, as described in this user guide. Please ensure that this guide is fully understood before operating the appliance. Use only attachments recommended or supplied by Hoover.

WARNING: Electricity can be extremely dangerous. This appliance is double insulated and must not be earthed. This plug is fitted with a 13 amp fuse (UK only).

IMPORTANT: The wires in the mains power lead are coloured in accordance with the following code:

Blue - Neutral Brown - Live

STATIC ELECTRICITY: Some carpets can cause a small build up of static electricity. Any static discharge is not hazardous to health.

AFTER USE: Switch the cleaner off and remove the plug from the electricity supply. Always switch off and remove the plug before cleaning the appliance or attempting any maintenance task.

SAFETY WITH CHILDREN, ELDERLY OR THE INFIRM: Do not let children play with the appliance or its controls. Please supervise the use of the appliance by older children, the elderly or the infirm.

HOOVER SERVICE: To ensure the continued safe and efficient operation of this appliance, we recommend that any servicing or repairs are only carried out by an authorized Hoover service engineer.

IT IS IMPORTANT THAT YOU DO NOT:

Position the cleaner above you when cleaning the stairs.

Use your cleaner out of doors or on any wet surface or for wet pick up.

Pick up hard or sharp objects, matches, hot ashes, cigarette ends or other similar items.

Spray with or pick up flammable liquids, cleaning fluids, aerosols or their vapours as this may cause risk of fire or explosion.

Run over the supply cord when using your cleaner or remove the plug by pulling on the supply cord.

Stand on or wrap the power cord around arms or legs when using the cleaner.

Use the appliance to clean people or animals.

Continue to use your cleaner if it appears to be faulty. If the supply cord is damaged, stop using the cleaner IMMEDIATELY. To avoid a safety hazard, an authorized Hoover service engineer must replace the supply cord.

GETTING TO KNOW YOUR CLEANER

A. Main Cleaner

B. Cord Rewind Pedal

C. Carry Handle

D. Exhaust Filter Cover

E. On/Off Pedal

F. Telescopic Tube*

G. Telescopic Tube Release Button*

H. Standard Tube*

1. I. Variable Power Control Roller*

J. Bag Check Indicator

K. Bag Door Release Latch

L. Suction Regulator*

M. Handle

N. Carpet and Floor Nozzle**

O. Surface Selector Pedal

P. Hose

Q. Pre-Motor Filter

R. Exhaust filter

S. 2 in 1 Tool

T. Pet Hair Remover Mini Turbo Nozzle*

U. Allergen Remover Mini Turbo Nozzle*

V. Grand Turbo Nozzle*

W. Hard Floor Caresse Nozzle*

ASSEMBLING YOUR CLEANER

Remove all components from the packaging.

Connect the hose to the cleaner main body, ensuring it clips and locks into position. To 1.

release: simply press the two buttons on the hose end and pull [2].

1. Connect the tube upper end to the handle. [3].
2. Connect the tube lower end to the carpet and floor nozzle [4].

USING YOUR CLEANER

Extract power cord and plug it into the power supply. Do not pull the cord beyond the red 1.

marker [5].

Adjust the length of the telescopic tube* by moving the telescopic release button* up and down.

Raise or lower the handle to the most comfortable cleaning position [6].

1. Carpet & Floor Nozzle. Press the pedal on the nozzle [7] to select the ideal cleaning mode

for the floor type.

Hard Floor: The brushes are lowered to protect the floor.

Carpet: With lifted brushes for the deepest clean.

1. Switch the cleaner on by pressing the On/Off pedal on the cleaner main body. [8]
2. Adjust the power level by rotating the variable power control roller*. [9]
3. Adjust the suction regulator to the desired level. [10].

Switch off at the end of use by pressing the On/Off pedal. Unplug and press the cord rewind pedal.

pedal to wind the power cord back into the cleaner [11].

Parking and Storage - The tube can be parked for temporary storage while in use, or in the

storage position when not in use [12].

*Certain models only

**Nozzle design may vary according to model

1

CLEANER MAINTENANCE

Replacing The Dust Bag

If the bag check indicator is red, please check and, if necessary, replace the bag.

1. Lift the bag door release latch [13] to open the cover, pull the bag holder [14], and pull the bag collar to remove the bag [15].
2. Apply the peel and seal sticker, located on the bag collar, to the bag inlet. The full dust bag should be disposed of correctly and carefully.

Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder. 3.

Refit the bag holder and close the bag door. 4.

Warning - The bag door will NOT close if the dust bag and/or the bag holder are not assembled to the cleaner. Always ensure the bag and bag holder are present when closing the bag door.

Remember: The bag check indicator may also be red if an obstruction has occurred. In this case, refer to 'Removing A Blockage From the System'.

Cleaning the Filters

To maintain optimum performance of your cleaner, please wash the filters after each 5 bag changes.

Cleaning the pre-motor filter:

Lift the bag door release latch 1. [13] to open the cover and remove the bag holder.

To remove the pre-motor filter slide the pre-motor filter frame from the cleaner. 2. [16] Remove the filter from the holder.3. [17]

1. Wash it in hand warm water, [20] and allow it to dry thoroughly before replacing to the cleaner [21].

Cleaning the exhaust filter:

1. To remove the exhaust filter, unclip the exhaust filter cover [18] and remove the filter pack. [19]
2. Wash the filter in hand warm water [20] and allow it to dry thoroughly before replacing to the cleaner. [21].

Remember: Do not use hot water or detergents. In the unlikely event of the filters becoming damaged, fit a Genuine Hoover replacement. Do not try and use the product without a dust bag or filter fitted.

Cleaning the permanent cloth dust bag*

To maintain optimum performance we recommend that you wash the permanent cloth dust bag under hand warm water after every 5 full bags. Remove excess water and leave to dry fully before replacing.

*Certain models only

2

GB

Removing a Blockage From The System

If the bag check indicator is illuminated or flashing:

1. Check if the bag is full. If so refer to 'Replacing The Dust Bag'.
2. If it is not full, then;

A. Do the filters need cleaning? If so refer to 'Cleaning the Filter'.

B. Check if there is any other blockage in the system - Use a rod or a pole to remove any blockage from the Teletube or flexible hose.

Warning - The bag check indicator will turn red if the cleaner is used when full, if there is a blockage or if the filters are dirty. If the cleaner is used for a significant period of time with the bag check indicator is red, a thermal cut out will switch the cleaner off to prevent overheating. The bag check indicator turn green once the cleaner has switched off to signal that the thermal cut out has been activated. If this should happen, switch the cleaner off, unplug and correct the fault. It will take about 30 minutes for the cut out to automatically reset.

ACCESSORIES AND NOZZLES

All accessories can be fitted to the end of the handle or the end of the tube. [23]

2 in 1 tool – Combines two functions in one, the 2 in 1 tool can be connected as a crevice tool. By rotating the end piece converts to a dusting brush. The 2 in 1 tool can be stored neatly at the rear of the cleaner. [22]

Crevice Tool – For corners and hard to reach areas.

Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. To extend the brushes, push the button on the body of the tool.

Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep cleaning on textile surfaces and other hard to clean areas [1T].

Allergen Remover Mini Turbo Nozzle® – Use the mini turbo nozzle on stairs or for deep cleaning on textile surfaces and other hard to clean areas. [1U]

Grand Turbo Nozzle* - Use the turbo nozzle for deep cleaning on carpets. [1V]

Hard Floor Caresse Nozzle* – For wooden floors and other delicate floors. [1W]

IMPORTANT: Do not use the grand turbo nozzle or mini turbo nozzles on rugs with long fringes, animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.

USER CHECKLIST

Should you have a problem with the product, complete this simple user checklist before calling your local Hoover service.

• Is there a working electricity supply to the cleaner? Please check with another electrical appliance. Is the dust bag over-filled? Please refer to 'Cleaner Maintenance'. Is the filter blocked? Please refer to 'Cleaning the filter'. Is the hose or nozzle blocked? Please refer to 'Removing a blockage from the system'.
• Has the cleaner overheated? If so, it will take approximately 30 minutes to automatically reset.

IMPORTANT INFORMATION

Hoover spares and Consumables

Always replace parts with genuine Hoover spares. These are available from your local Hoover dealer or direct from Hoover. When ordering parts always quote your model number.

Consumables:

PAPER BAG: H64, 35600637.

HEPA BAG: H63, 35600536.

FILTER KIT (pre-motor and exhaust): U63, 35601193.

Spares:

CARPET & FLOOR NOZZLE: G130, 35601195.

• PARQUET CARESSE NOZZLE: G131 PC, 35601196 • GRAND TURBO NOZZLE: J54, 35601197 • PET HAIR MINI TURBO NOZZLE: J46, 35601116 • COMPLETE FLEXIBLE HOSE: D128, 35601194

Hoover Service

Should you require service at any time, please contact your local Hoover Service Office.

Quality

BSI ISO 9001

Hoover's factories have been independently assessed for quality. Our products are made using a quality system which meets the requirements of ISO 9001.

The Environment:

This appliance is marked according to the European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the appliance collection point for recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with the local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Your Guarantee

The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.

Subject to change without notice.

3

IMPORTANT SAFETY NOTES

ACCESSORIES AND BRUSHES

PAPER BAG: H64, 35600637

HEPA BAG: H63, 35600536.

B. Pedal recogecable

PAPER BAG: H64, 35600637•

HEPA BAG: H63, 35600536.

MAINTENANCE OF THE VACUUM CLEANER

Replacing the dust bag

PAPIRPOSE: H64, 35600637.

HEPA POSE: H63, 35600536.

FILTERPAKKE (pre-motor and exhaust): U63, 35601193.

Spare parts:

NOZZLE FOR CARPET AND FLOOR: G130, 35601195

• PARQUET CARESSE NOZZLE: G131 PC, 35601196 - LARGE TURBO NOZZLE: J54, 35601197 • MINI TURBO NOZZLE FOR PET HAIR: J46, 35601116 • FLEXIBLE HOSE: D128, 35601194

Hoover service

If you ever need service, please contact your local Hoover service center.

Quality

BSI ISO 9001

SE

USER CHECKLIST