LMD-2110MD - Monitor SONY - Free user manual and instructions

Product Type	Medical Monitor
Brand	Sony
Model	LMD-2110MD
Screen Size	21 inches (diagonal)
Resolution	1920 x 1080 pixels (Full HD)
Display Technology	LCD
Brightness	300 cd/m²
Contrast Ratio	1000:1
Viewing Angle	178° horizontal and vertical
Video Inputs	HDMI, DisplayPort, DVI-D, VGA
Power Supply	AC 100-240 V, 50/60 Hz
Power Consumption	45 W (typical)
Dimensions (W x H x D)	505 x 320 x 70 mm (without stand)
Weight	6.5 kg (approx.)
VESA Mount	Yes, 100 x 100 mm
Intended Use	Medical imaging and diagnosis
Care and Cleaning	Clean with a soft, dry cloth. Do not use solvents.
Safety	Comply with applicable medical standards. Use only by qualified personnel.
Spare Parts and Repairability	Contact an authorized Sony after-sales service for any repairs.
General Information	Monitor designed for clinical environments, compatible with medical imaging standards.

Frequently Asked Questions - LMD-2110MD SONY

How do I adjust brightness and contrast?

Use the dedicated buttons on the front panel or access the OSD (On-Screen Display) menu via the Menu button. Navigate with the arrow keys to adjust brightness and contrast.

What video inputs are available?

The Sony LMD-2110MD has HDMI, DisplayPort, DVI-D, and VGA inputs. Select the source in the input menu.

Can I mount the monitor on an articulating arm?

Yes, the monitor is compatible with the VESA 100 x 100 mm standard. Remove the stand to attach the mount.

How do I clean the screen without damaging it?

Use a soft, lint-free cloth, slightly dampened with water if necessary. Never use chemicals, alcohol, or solvents.

Is the monitor suitable for surgical use?

It is designed for medical imaging and diagnosis. For use in operating rooms, check sterilization standards and compatibility with your equipment.

What should I do if the screen remains black?

Check that the power cable is plugged in and the power switch is on. Make sure the video source is correctly selected. If the problem persists, contact technical support.

How do I update the firmware?

Download the latest version from the Sony Support website, transfer it to a USB drive, and follow the update instructions in the Service menu of the monitor.

The monitor emits a humming sound, is this normal?

A slight hum may come from the internal power supply or backlight. If the noise is loud or intermittent, have the device checked.

What is the warranty on this monitor?

The standard Sony warranty for medical monitors is 2 years (parts and labor). Check the exact terms in your country.

Can I use the monitor with a standard computer?

Yes, it is compatible with any computer equipped with an HDMI, DisplayPort, DVI, or VGA output. Display performance is optimized for medical color accuracy.

USER MANUAL LMD-2110MD SONY

Instructions for Use Page 28 GB

© 2011 Sony Corporation

Please provide with the protection cover for the connector when you do not use the specified connectors.

Tally lamp

HDMI IN terminal

To disconnect the power cord

80° / 80° / 85° / 85° (typical)

Scan normal 0%

Over 5%

Aspect ratio 16:9

Color reproduction 16.77 million colors

Input/output system

Input

LINE input

Before operating the unit, please read this manual thoroughly and retain it for future reference.

Owner's Record

The model and serial numbers are located at the rear. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. ____ Serial No. ____

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

No modification of this apparatus is allowed.

WARNING THIS APPARATUS MUST BE EARTHED.

To disconnect the main power, unplug the AC plug.

CAUTION

The apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.

WARNING

Make sure the surface is wide enough so that this apparatus's width and depth don't exceed the surface's edges.

If not, this apparatus may lean or fall over and cause an injury.

Consult with Sony qualified personnel for mounting arm, wall or ceiling mount installation.

Do not install the appliance in a confined space, such as book case or built-in cabinet.

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING:

Using this unit at a voltage other than 120 V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

For the customers in Canada

This unit has been certified according to Standard CAN/CSA-C22.2 No. 60601-1.

For the customers in the U.S.A and Canada

When you use this product connected to 240 V single phase, be sure to connect this product to a center tapped circuit.

For the customers in Europe

This product has been manufactured by or on behalf of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters, please refer to the addresses provided in the separate service or guarantee documents.

Important safeguards/notices for use in the medical environments

1. All the equipments connected to this unit shall be certified according to Standard IEC60601-1, IEC60950-1, IEC60065 or other IEC/ISO Standards applicable to the equipments.
2. Furthermore all configurations shall comply with the system standard IEC60601-1-1.

Everybody who connects additional equipment to the signal input part or signal output part configures a medical system, and is therefore, responsible that the system complies with the requirements of the system standard IEC60601-1-1.

If in doubt, consult the qualified service personnel.

1. The leakage current could increase when connected to other equipment.
2. For this particular equipment, all accessory equipment connected as noted above, must be connected to mains via an additional isolation transformer conforming with the construction requirements of IEC60601-1 and providing at least Basic Insulation.
3. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause interference to other equipment. If this unit causes interference (which can be determined by unplugging the power cord from the unit), try these measures: Relocate the unit with respect to the susceptible equipment. Plug this unit and the susceptible equipment into different branch circuit.

Consult your dealer. (According to standard EN60601-1-2 and CISPR11, Class B, Group 1)

1. Model LMD-2110MD is a monitor intended for use in a medical environment to display pictures from cameras or other systems, other than diagnostic X-ray equipment.

WARNING

When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

Caution

When you dispose of the unit or accessories, you must obey the laws in the relative area or country and the regulations in the relative hospital.

WARNING on power connection

Use a proper power cord for your local power supply.

1. Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere).

If you have questions on the use of the above Power Cord / Appliance Connector / Plug, please consult a qualified service personnel.

WARNING on power connection for medical use

Please use the following power supply cord. With connectors (plug or female) and cord types other than those indicated in this table, use the power supply cord that is approved for use in your area.

	United States and Canada
Plug Type HOSPITAL GRADE*
Cord type Min. Type	SJTMin. 18 AWG
Minimum Rating for Plug and Appliance Couplers	10A/125V
Safety Approval UL	Listed and CSA

*Note: Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked 'Hospital Only' or 'Hospital Grade'.

For customers in Norway

This equipment can be connected to an IT power distribution system.

Symbol	Location This symbol indicates
	Front Standby switch.
	Rear The equipotential terminal which brings the various parts of a system to the same potential.
	Rear Functional earth terminal
	Front Key inhibit	The setting are locked so that they cannot be changed.

CAUTION

Please provide the protection cover for the connector when you do not use the specified connectors.

This CAUTION is located on the rear of the unit.

See page 42 of these instructions for details about how to attach the connector cover.

Refer to the operating instructions

Follow the directions in the operating instructions for parts of the unit on which this mark appears.

This symbol indicates the manufacturer, and appears next to the manufacturer's name and address.

Important EMC notices for use in the medical environments

• The LMD-2110MD needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in this instructions for use.
• The portable and mobile RF communications equipment such as cellular phones can affect the LMD-2110MD.

Warning

The use of accessories and cables other than those specified, with the exception of replacement parts sold by Sony Corporation, may result in increased emissions or decreased immunity of the LMD-2110MD.

Guidance and manufacturer's declaration-electromagnetic emissions
The LMD-2110MD is intended for use in the electromagnetic environment specified below.The customer or the user of the LMD-2110MD should assure that it is used in such an environment.
Emission test Compliance Electromagnetic environment-guidance
RF emissionsCISPR 11	Group 1	The LMD-2110MD uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
RF emissionsCISPR 11	Class B	The LMD-2110MD is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Harmonic emissionsIEC 61000-3-2	Class D
Voltage fluctuations/flicker emissionsIEC 61000-3-3	Complies

Warning

If the LMD-2110MD should be used adjacent to or stacked with other equipment, it should be observed to verify normal operation in the configuration in which it will be used.

Guidance and manufacturer's declaration - electromagnetic immunity
The LMD-2110MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-2110MD should assure that it is used in such as environment.
Immunity test	IEC 60601 test level	Compliance level E	electromagnetic environment - guidance
Electrostatic discharge (ESD)	±6 kV contact	±6 kV contact	Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
	±8 kV air	±8 kV air
IEC 61000-4-2
Electrical fast transient/burst	±2 kV for power supply lines	±2 kV for power supply lines	Mains power quality should be that of a typical commercial or hospital environment.
IEC 61000-4-4	±1 kV for input/output lines	±1 kV for input/output lines
Surge	±1 kV differential mode	±1 kV differential mode	Mains power quality should be that of a typical commercial or hospital environment.
IEC 61000-4-5	±2 kV common mode	±2 kV common mode
Voltage dips, short interruptions and voltage variations on power supply input lines	< 5% UT (>95% dip in UT )for 0.5 cycle	< 5% UT (>95% dip in UT )for 0.5 cycle	Mains power quality should be that of a typical commercial or hospital environment. If the user of the LMD-2110MD requires continued operation during power mains interruptions, it is recommended that the LMD-2110MD be powered from an uninterruptible power supply or a battery.
IEC 61000-4-11	40% UT (60% dip in UT )for 5 cycles	40% UT (60% dip in UT )for 5 cycles
	70% UT (30% dip in UT )for 25 cycles	70% UT (30% dip in UT )for 25 cycles
	< 5% UT (>95% dip in UT )for 5 sec	< 5% UT (>95% dip in UT )for 5 sec
Power frequency (50/60Hz)magnetic field	3 A/m 3 A/m Power frequency magnetic fields should be at least characteristic of a typical location in a typical commercial or hospital environment.
IEC 61000-4-8
NOTE: UT is the a.c. mains voltage prior to application of the test level.
Immunity test	IEC 60601 test level	Compliance level E	Electromagnetic environment - guidance
Conducted RF	3 Vrms	3 Vrms	Portable and mobile RF communications equipment should be used no closer to any part of the LMD-2110MD, including cables, than the recommended separation distance calculated from the equation appliance to the frequency of the transmitter.
IEC 61000-4-6	150 kHz to 80 MHz		Recommended separation distance d = 1.2 d = 1.2 80MHzto 800MHz d = 2.3 800MHzto 2.5GHz
Radiated RF	3 V/m	3 V/m	Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m).Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than the compliance level in each frequency range. b Interference may occur in the vicinity of equipment marked with following symbol:
IEC 61000-4-3	80 MHz to 2.5 GHz
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the LMD-2110MD is used exceeds the applicable RF compliance level above, the LMD-2110MD should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the LMD-2110MD.b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.Recommended separation distances between portable and mobile RF communications equipment and the LMD-2110MD
The LMD-2110MD is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the LMD-2110MD can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (Transmitters) and the LMD-2110MD as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output power of transmitter W	Separation distance according to frequency of transmitter m
	150 kHz to 80 MHz d = 1.2	80 MHz to 800 MHz d = 1.2	800 MHz to 2.5 GHz d = 2.3
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

Table of Contents

Precaution 35

On Safety 35

On Installation 35

About the LCD Panel 35

On Burn-in 35

On a Long Period of Use 35

On Cleaning 36

Disposal of the Unit 36

Recommendation to Use more than One Unit 36

On Repacking 36

On Fan Error 36

On Moisture Condensation 36

Features 37

Location and Function of Parts and

Controls 38

Front Panel 38

Input Signals and Adjustable/Setting Items ..... 39

Rear Panel 40

Connecting the AC Power Cord 41

Attaching the Input Adaptor 42

Removing the Connector Cover 42

Selecting the Default Settings 43

Selecting the Menu Language 44

Using the Menu 45

Adjustment Using the Menus 46

Items 46

Adjusting and Changing the Settings 47

STATUS menu.... 47

COLOR TEMP/BAL menu 47

USER CONTROL menu.... 48

SYSTEM SETTING menu 48

REMOTE menu 50

KEY INHIBIT menu.... 50

Troubleshooting 51

Specifications 51

Dimensions 55

Precaution

On Safety

• Operate the unit only with a power source as specified in the “Specifications” section.
• A nameplate indicating operating voltage, etc., is located on the rear panel.
• Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
• Do not drop or place heavy objects on the power cord. If the power cord is damaged, turn off the power immediately. It is dangerous to use the unit with a damaged power cord.
• Unplug the unit from the wall outlet if it is not to be used for several days or more.
• Disconnect the power cord from the AC outlet by grasping the plug, not by pulling the cord.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.

On Installation

• Prevent internal heat build-up allowing adequate air circulation. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes.
• Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
• Do not place the monitor near equipment which generates magnetism, such as a transformer or high voltage power lines.

About the LCD Panel

• The LCD panel fitted to this unit is manufactured with high precision technology, giving a functioning pixel ratio of at least 99.99%. Thus a very small proportion of pixels may be “stuck”, either always off (black), always on (red, green, or blue), or flashing. In addition, over a long period of use, because of the physical characteristics of the liquid crystal display, such “stuck” pixels may appear spontaneously. These problems are not a malfunction.
• Do not leave the LCD screen facing the sun as it can damage the LCD screen. Take care when you place the unit by a window.
• Do not push or scratch the LCD screen. Do not place a heavy object on the LCD screen. This may cause the screen to lose uniformity.
• If the unit is used in a cold place, a residual image may appear on the screen. This is not a malfunction. When the monitor becomes warm, the screen returns to normal.
• The screen and the cabinet become warm during operation. This is not a malfunction.

On Burn-in

For LCD panel, permanent burn-in may occur if still images are displayed in the same position on the screen continuously, or repeatedly over extended periods.

Images that may cause burn-in

• Masked images with aspect ratios other than 16:9 • Color bars or images that remain static for a long time
• Character or message displays that indicate settings or the operating state

To reduce the risk of burn-in

• Turn off the character displays Press the MENU button to turn off the character displays. To turn off the character displays of the connected equipment, operate the connected equipment accordingly. For details, refer to the operation manual of the connected equipment.

- Turn off the power when not in use Turn off the power if the monitor is not to be used for a prolonged period of time.

On a Long Period of Use

Due to the characteristics of LCD panel, displaying static images for extended periods, or using the unit repeatedly in a high temperature/high humidity environments may cause image smearing, burn-in, areas of which brightness is permanently changed, lines, or a decrease in overall brightness.

In particular, continued display of an image smaller than the monitor screen, such as in a different aspect ratio, may shorten the life of the unit.

Avoid displaying a still image for an extended period, or using the unit repeatedly in a high temperature/high humidity environment such as airtight room, or around the outlet of an air conditioner.

To prevent any of the above issues, we recommend reducing brightness slightly, and to turn off the power whenever the unit is not in use.

On Cleaning

Before cleaning

Be sure to disconnect the AC power cord from the AC outlet.

On cleaning the monitor

A material that withstands disinfection is used for the medical use LCD monitor. When solvents such as benzene or thinner, or acid, alkaline or abrasive detergent, or chemical cleaning cloth are used for the monitor surface, the performance of the monitor may be impaired or the finish of the surface may be damaged. Take care with respect to the following:

• Clean the monitor surface with a 50 to 70 v/v% concentration of isopropyl alcohol or a 76.9 to 81.4 v/v% concentration of ethanol using a swab method. Wipe the monitor surface gently (wipe using less than 1 N force).
• Stubborn stains may be removed with a soft cloth, such as a cleaning cloth, lightly dampened with a mild detergent solution using a swab method, and then clean using the above chemical solution.

Never use solvents such as benzene or thinner, or acid, alkaline, or abrasive detergents, or chemical cleaning cloths for cleaning or disinfection, as they will damage the monitor surface.

• Do not use unnecessary force to rub the monitor surface with a stained cloth. The monitor surface may be scratched.
• Do not keep the monitor surface in contact with a rubber or vinyl resin product for a long period of time. The finish of the surface may deteriorate or the coating may come off.

Disposal of the Unit

Do not dispose of the unit with general waste.

Do not include the monitor with household waste.

Recommendation to Use More than One Unit

As problems can occasionally occur for the monitor, when the monitor is used for safety control of personnel, assets, or stable picture, or for emergencies, we strongly recommend you use more than one unit or prepare a spare unit.

On Repacking

Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit.

If you have any questions about this unit, contact your authorized Sony dealer.

On Fan Error

The fan for cooling the unit is built in. When the fan stops and the ⬆ Indicator on the front panel blinks for fan error indication, turn off the power and contact an authorized Sony dealer.

On Moisture Condensation

If the unit is brought directly from a cold place to a warm place, or the unit is warm and the ambient temperature cools suddenly (by air-conditioning, for example), moisture may condense on the surface or inside of the unit.

This is called moisture condensation, and is not a malfunction of the product itself, although it may cause damage to the unit.

Leave the unit in a condensation free area.

If moisture condensation has occurred, turn off the unit and do not use it until moisture condensation has evaporated.

Features

The LMD-2110MD is a 21.5-type LCD monitor that conforms to medical safety standards. This unit is suitable for endoscopy or use as a sub-monitor.

Compliance with medical safety standards in U.S.A., Canada and Europe

IEC 60601-1 and product safety standards in the U.S.A., Canada and Europe have been obtained for this monitor.

High brightness LCD panel

Because of precise image and high speed response, real color image can be reproduced.

Monitor stand with tilt function

As the stand with tilt function is equipped normally for the monitor, you can use it easily on the desk top.

Tally lamp

The green LED lamp is used for the tally lamp. You can check the status of the monitor, controlling the lamp from the external remote.

Multi-format

The monitor supports the video, Y/C, RGB, component and HDMI ¹⁾ input signals.

Both NTSC and PAL color systems are supported, and the appropriate color system is selected automatically. HD/SD-SDI signals can be available when input adaptor BKM-341HS (optional) is used.

For more information, see “Video signal formats” (page 53).

1) HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Blue only mode

In the blue only mode, an apparent monochrome display is obtained with all three of the R/G/B cathodes driven with a blue signal. This facilitates color saturation and phase adjustments and observation of signal noise.

Analog RGB/component input connectors

Analog RGB or component signals from video equipment can be input through these connectors.

Y/C input connectors

Y/C signals of the video signal can be input through this connector.

External sync input

When the EXT SYNC button is in the on position, the unit can be operated on the sync signal supplied from an external sync generator.

Automatic termination (connector with mark only)

The input connector is terminated internally at 75 ohms when nothing has been connected to the output connector. If a cable is connected to the output connector, the internal terminal is automatically released and the signals input to the input connector are output to the output connector (loop-through).

Select color temperature and gamma mode

You can select the color temperature from among three (HIGH, LOW and LOW2) settings and gamma mode from among five settings. You can also adjust the color temperature to the appropriate setting.

Aspect setting

You can set the monitor to 4:3, 16:9 or 5:4 display mode according to the input video signal.

Scan setting

You can set the display size to normal scan, over scan or full screen.

Key inhibit function

You can inhibit a key function to prevent misoperation.

Select language display

You can select from seven display languages English, Chinese, Japanese, Italian, Spanish, German and French.

External remote control function

You can directly select the input signal, aspect, etc., by operating the equipment connected to the PARALLEL REMOTE terminal.

I/P mode setting

This unit is equipped with an I/P mode setting function that is used to minimize picture delay due to the signal conversion process.

Two kinds of ground terminals

Two kinds of ground terminals are built into the monitor to equal the electric potential.

Location and Function of Parts and Controls

Front Panel

①Tally lamp

Turning this lamp on or off can be done with a PARALLEL REMOTE connector.

For details, see "Pin assignment" (page 52).

② (standby) switch and indicator

Press to turn on the power when this unit is in standby mode. The indicator turns on. Press again to set the monitor in standby mode. The indicator goes out.

③○—(key inhibit) indicator

Lights when the key inhibit function works. The indicator blinks when fan error occurs.

For details on the key inhibit, see “KEY INHIBIT menu” (page 50).

④VOLUME buttons

Press the + button to increase the volume or the - button to decrease it.

⑤Menu operation buttons

Displays or sets the on-screen menu.

↑/↓/←/→ (arrow) buttons

Select the menu or make various adjustments.

MENU button

Press to display the on-screen menu. Press again to clear the menu.

RESET button

Resets the value of an item back to the previous value. This button functions when the menu item is adjusted (displayed) on the screen.

ENTER button

Press to confirm a selected item on the menu.

⑥ASPECT select button

Press to set the aspect ratio of the picture, 16:9, 4:3 or 5:4.

⑦SCAN select button

You can change the scan size of the picture. Press to change the scan size among over (5% over scan), normal (0% scan) and full screen set on the SCAN menu (page 48).

⑧BLUE ONLY button

Press to eliminate the red and green signals. Only blue signal is displayed as a monochrome picture on the screen. This mode is convenient for chroma and phase adjustments and monitoring of signal noise.

⑨EXT SYNC (external sync) button

Press to operate the unit on an external sync signal through the EXT SYNC IN connector. The EXT SYNC button works when the component/RGB signals are input.

⑩ SDI button

Press to monitor the signal through the OPTION IN connector.

⑪ RGB/COMPONENT button

Press to monitor the signal through the RGB/COMPONENT input connector.

⑫ HDMI button

Press to monitor the signal through the HDMI IN connector.

⑬ LINE button

Press to monitor the signal through the LINE input connector.

⑭ Speaker

The audio signal selected by the input select button (⑩ SDI button, ⑪ RGB/COMPONENT button, ⑫ HDMI button, or ⑬ LINE button) on the front panel is output.

Input Signals and Adjustable/Setting Items

O: Adjustable/can be set ×: Not adjustable/cannot be set *1 When a component signal (480/60I) is input, this can be switchable. *2 When a 480/60P or 576/50P signal is input, this can be switchable. *3 When an interlace signal is input, this can be switchable. *4 When BKM-341HS is used, SDI signals can be input. *5 When a PC signal is input to the HDMI IN connector using a DVI conversion cable, this can be adjusted.

Rear Panel

① HDMI IN connector

HDMI (High-Definition Multimedia Interface) is an interface that supports both video and audio on a single digital connection, allowing you to enjoy high quality digital picture and sound. The HDMI specification supports HDCP (High-bandwidth Digital Content Protection), a copy protection technology that incorporates coding technology for digital video signals.

Notes

• Use an HDMI compliant cable (optional) with the HDMI logo. • Color noise may appear on the edge of the screen depending on the connected device. This is not a malfunction.

②HDMI cable holder

Secures the HDMI cable (7 mm or less in diameter).

③OPTION IN connector (D-sub 9-pin, female)

Inputs HD/SD-SDI signals when the optional Sony BKM-341HS is connected.

Press the SDI button to select the signal.

Note

Do not connect equipment other than the BKM-341HS. It may cause damage to the unit or the equipment.

④OPTION AUDIO IN connector (phono jack)

Inputs an audio signal if the BKM-341HS is connected to the OPTION IN connector.

Press the SDI button to monitor the audio signal.

⑤EXT SYNC IN/OUT (external sync) connectors (BNC)

Press the EXT SYNC button to use the sync signal through this connector.

IN connector

When this unit operates on an external sync signal, connect the reference signal from a sync generator to this connector.

Note

When inputting a video signal with jitters, etc., the picture may be disturbed. We recommend using the TBC (time base corrector).

OUT connector

Loop-through output of the IN connector. Connect to the external sync input of video equipment to be synchronized with this unit.

When the cable is connected to this connector, the 75-ohm termination of the input is automatically released, and the signal input to the IN connector is output from this connector.

⑥ RGB/COMPONENT connectors

Analog RGB signal or component (Y/PB/PR) signal input connectors and their loop-through output connectors.

Press the RGB/COMPONENT button to monitor the signal input through these connectors.

G/Y, B/PB, R/PR IN/OUT (BNC)

These are the input/output connectors for an analog RGB and a component (Y/PB/PR) signal. Unless an external sync signal is input, the monitor is synchronized with the sync signal contained in the G/Y signal.

AUDIO IN/OUT (phono jack)

When using an analog RGB or a component signal as a video signal, use these jacks for the input/output of an audio signal. Connect them to the audio input/output jacks on equipment such as a VCR.

⑦ PARALLEL REMOTE connector (modular connector, 8-pin)

Forms a parallel switch and controls the monitor externally.

When the unit is shipped from the factory, a connector cover is attached to this connector. Remove it before using the connector.

For removing the connector cover, see page 42.

For details on the pin assignment and factory setting function assigned to each pin, see page 52.

CAUTION

For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port.

⑧ LINE connectors

Line input connectors for Y/C separate, composite video and audio signals and their loop-through output connectors.

Press the LINE button to monitor the signal input through these connectors.

If you input signals to both Y/C IN and VIDEO IN, the signal input to the Y/C IN is selected.

Y/C IN/OUT (4-pin mini-DIN)

These are the input/output connectors for a Y/C separate signal. Connect them to the Y/C separate input/output connectors on equipment such as a VCR, video camera, or another monitor.

VIDEO IN/OUT (BNC)

These are the input/output connectors for a composite video signal. Connect them to the composite video input/output connectors on equipment such as a VCR, video camera, or another monitor.

AUDIO IN/OUT (phono jack)

These are the input/output jacks for an audio signal. Connect them to the audio input/output jacks on equipment such as a VCR.

⑨ ∇/≡ (Equipotential/Function Earth) terminal

Connects the earth cable.

⑩ AC IN socket

Connect the supplied AC power cord.

Connecting the AC Power Cord

1. Plug the AC power cord into the AC IN socket on the rear panel. Then, attach the AC plug holder (supplied) to the AC power cord.

2. Slide the AC plug holder over the cord until it locks.

To disconnect the AC power cord

Pull out the AC plug holder while pressing the lock levers.

Attaching the Input Adaptor

Before attaching the input adaptor, disconnect the power cord.

BKM-341HS

Note

Do not connect equipment other than the BKM-341HS. It may cause damage to the unit or the equipment.

Removing the Connector Cover

When the unit is shipped from the factory, a connector cover is attached to the PARALLEL REMOTE connector.

To use the connector, remove the connector cover as follows.

Before removing the connector cover, disconnect the power cord.

1. Remove the screw of the connector cover.

2. Remove the connector cover.

Save the screw and cover, so that you can reattach the cover if necessary.

Caution

This connector is designed to allow direct contact with conductive circuits. Weak voltage may be present because of a failure in this unit. To prevent patients from touching this connector accidentally, attach the connector cover when the connector is not being used to connect to other devices.

Selecting the Default Settings

When you turn on the unit for the first time after purchasing it, select the area where you intend to use this unit from among the options.

The default setting values for each area

		COLOR TEMP	COMPONENT LEVEL	NTSC SETUP
1NORTH AMERICA LOW BETA7.5 7.5
2LATIN AMERICAPAL&PAL-NAREA	ARGENTINA LOW SMPTE 0
	PARAGUAY LOW SMPTE 0
	URUGUAY LOW SMPTE 0
NTSC&PAL-MAREA	OTHER AREA LOW BETA7.5 7.5
3AFRICA AUSTRALASIA EUROPE MIDDLE-EAST		LOW SMPTE 0
4ASIA EXCEPTJAPAN	NTSC AREA LOW BETA7.5 7.5
	PAL AREA LOW SMPTE 0
5JAPAN HIGH SMPTE 0

1. Press the ⏻ (standby) switch.

The power is turned on and the SELECT SETTING screen appears.

2. Press the ↑ or ↓ button to select the area where you intend to use the unit and press the → or ENTER button.

If you select either ①, ③ or ⑤

The confirmation screen is displayed. Confirm the selected area. When the setting is wrong, press the ← button to return to the previous screen.

SELECT THIS AREA?

NORTH AMERICA

[ENTER] YES

[MENU] NO

If you select either ② or ④

One of the following screens appears. Press the ↑ or ↓ button to narrow the area further and then press the → or ENTER button.

The confirmation screen is displayed. Confirm the selected area. When the setting is wrong, press the ← button to return to the previous screen.

② If LATIN AMERICA is selected:

④ If ASIA EXCEPT JAPAN is selected:

Customers who will use this unit in the shaded areas shown in the map below should select NTSC AREA.

Other customers should select PAL AREA.

3 Press the ↑ or ↓ button to narrow the area further and then press the → or ENTER button.

The SELECT SETTING screen disappears and the menu item settings suitable for the selected area are applied.

Note

When you have selected the wrong area, set the following items using the menu.

• COLOR TEMP (on page 47) • COMPONENT LEVEL (on page 48) • NTSC SETUP (on page 48)

See “The default setting values for each area” (page 43) for the setting value.

Selecting the Menu Language

You can select one of seven languages (English, Chinese, Japanese, Italian, Spanish, German, French) for displaying the menu and other on-screen displays. "ENGLISH (English)" is selected in the default setting. The current settings are displayed in place of the ■ marks on the illustrations of the menu screen.

1 Press the ⏻ (standby) switch to turn on the unit.

2 Press the MENU button.

The menu appears.

The menu presently selected is shown in yellow.

3 Press the ↑ or ↓ button to select SYSTEM SETTING menu, then press the → or ENTER button.

The setting items (icons) in the selected menu are displayed in yellow.

4 Press the ↑ or ↓ button to select "LANGUAGE," then press the → or ENTER button.

The selected item is displayed in yellow.

5 Press the ↑ or ↓ button to select a language, then press the ENTER button.

The menu changes to the selected language.

To clear the menu

Press the MENU button.

The menu disappears automatically if a button is not pressed for one minute.

Using the Menu

The unit is equipped with an on-screen menu for making various adjustments and settings such as picture control, input setting, set setting change, etc. You can also change the menu language displayed in the on-screen menu.

To change the menu language, see “Selecting the Menu Language” on page 44.

The current settings are displayed in place of the ■ marks on the illustrations of the menu screen.

1 Press the MENU button.

The menu appears.

The menu presently selected is shown in yellow.

2 Press the ↑ or ↓ button to select a menu, then press the → or ENTER button.

The menu icon presently selected is shown in yellow and setting items are displayed.

3 Press the ↑ or ↓ button to select the item, then press the → or ENTER button.

The item to be changed is displayed in yellow.

Note

If the menu consists of multiple pages, press ↑ or ↓ button to go to the desired menu page.

4 Make the setting or adjustment on an item.

When changing the adjustment level:

To increase the number, press the ↑ button. To decrease the number, press the ↓ button. Press the ENTER button to confirm the number, then restore the original screen.

When changing the setting:

Press the ↑ or ↓ button to change the setting. Press the ENTER button to confirm the setting.

Notes

• An item displayed in black cannot be accessed. You can access the item if it is displayed in white.
• If the key inhibit has been turned on, all items are displayed in black. To change any of the items, turn the key inhibit to OFF first.

For details on the key inhibit, see “KEY INHIBIT menu” (page 50).

To clear the menu

Press the MENU button.

The menu disappears automatically if a button is not pressed for one minute.

About the memory of the settings

The settings are automatically stored in the monitor memory.

To reset items that have been adjusted

Pressing the RESET button while you are adjusting any of the menu items resets the menu item to the previous setting.

Adjustment Using the Menus

Items

The screen menu of this monitor consists of the following items.

STATUS (the items indicate the current settings.)

For the video input

FORMAT

COLOR TEMP

GAMMA

COMPONENT LEVEL

NTSC SETUP

RGB/COMP SEL

SCAN MODE

ASPECT

Model name and serial number

OPTION

For the DVI input

FORMAT

fH

fV

COLOR TEMP

Model name and serial number

OPTION

COLOR TEMP/BAL

COLOR TEMP

MANUAL ADJUSTMENT

USER CONTROL

CONTROL

SYSTEM SETTING

RGB/COMP SEL

COMPONENT LEVEL

NTSC SETUP

SCAN

GAMMA

FORMAT DISPLAY

LANGUAGE

BACKGROUND

I/P MODE

SD PIXEL MAPPING

REMOTE

PARALLEL REMOTE

1PIN

2PIN

3PIN

4PIN

6PIN

7PIN

8PIN

KEY INHIBIT

KEY INHIBIT

Adjusting and Changing the Settings

STATUS menu

The STATUS menu is used to display the current status of the unit. The following items are displayed:

For the video input

• Signal format • Color temperature • Gamma • Component level • NTSC setup • RGB/Component select • Scan mode • Aspect • Model name and serial number • Option

For the DVI input

• Signal format • fH • fV • Color temperature
• Model name and serial number
• Option

COLOR TEMP/BAL menu

The COLOR TEMP/BAL menu is used for adjusting the picture white balance.

You need to use the measurement instrument to adjust the white balance.

Recommended: Konica Minolta color analyzer CA-210

Submenu	Setting
COLOR TEMP	Selects the color temperature from among HIGH, LOW, USER setting and LOW2.

Submenu Setting

MANUALADJUSTMENT

If you set the COLOR TEMP to USER setting, the item displayed is changed from black to white, which means you can adjust the color temperature.• ADJUST GAIN: Adjusts the color balance (GAIN).• ADJUST BIAS: Adjusts the color balance (BIAS).• COPY FROM: If you select HIGH, LOW or LOW2, the white balance data for the selected color temperature will be copied in the USER setting.

USER CONTROL menu

The USER CONTROL menu is used for adjusting the picture.

Items that cannot be adjusted depending on the input signal are displayed in black.

For details of input signal and adjustable / setting items, see page 39.

Submenu Setting

CONTROL You can adjust the picture.

CONTRAST: Adjusts the picture contrast.BRIGHTNESS: Adjusts the picture brightness.CHROMA: Adjusts color intensity. The higher the setting, the greater the intensity. The lower the setting, the lower the intensity.PHASE: Adjusts color tones.The higher the setting, the more greenish the picture.The lower the setting, the more purplish the picture.APERTURE: Adjusts the picture sharpness.The higher the setting, the sharper the picture. The lower the setting, the softer the picture.BACKLIGHT: Adjusts the backlight. When the setting is changed, the brightness of the backlight is changed.

SYSTEM SETTING menu

The SYSTEM SETTING menu is used for setting the system. You can set the display language and so on. Items that cannot be adjusted depending on the input signal are displayed in black.

Submenu Setting

RGB/COMP SEL When a signal input via the RGB/COMPONENT connector is being monitored, based on the signal being input, select RGB or COMP (component).
COMPONENT LEVEL Selects the component level from among three modes.SMPTE: for 100/0/100/0 signalBETA7.5: for 100/7.5/75/7.5 signalBETA0: for 100/0/75/0 signal
NTSC SETUP Selects the NTSC setup level from two modes.The 7.5 setup level is used mainly in North America. The 0 setup level is used mainly in Japan.
SCAN Sets the scan size of the picture.Select from OFF and FULL.The display format changes depending on the mode selected.(See “Scan mode image” on page 50.)OFF: Changes between over scan and normal scan.FULL: Changes to over scan, normal scan or full screen.
GAMMA	Select the appropriate gamma mode. You can select from among five settings. When “3” is selected, the setting is roughly same as the gamma mode of the CRT (2.2).

Submenu Setting

FORMAT DISPLAY Selects the display mode of the signal format. • AUTO: The format is displayed for about 10 seconds when the input of the signal starts. • ON: The format is always displayed. • OFF: The display is hidden.
LANGUAGE Selects the menu or message language from among seven languages. • ENGLISH: English • 中文: C h i • 日本語ese • ITALIANO: Italian • ESPAÑOL: Spanish • DEUTSCH: German • FRANÇAIS: French
BACKGROUND Sets the brightness of the black bars appearing on the sides of the screen. • OFF: Displays a darker bar (black). • ON: Displays a brighter bar (gray).
I/P MODE (picture delay minimum)	Select to set the delay by the picture processing to the minimum level when the signal is input. • INTER-FIELD: Performs interpolation depending on the movement of the images between the fields. It takes longer than “LINE DOUBLER” for processing the picture. “INTER-FIELD” is the factory setting. • LINE DOUBLER: The processing time is shorter. Performs interpolation by repeating each line in the data receiving sequence regardless of the field. As the line flicker is displayed in this mode, it is available for checking the line flicker of the telop work and so on.

Submenu Setting

SD PIXEL MAPPING Selects SD picture size (pixels)according to input signal format.COMPOSITE&Y/C: Set to monitor the signal input through the LINE connector (VIDEO IN or Y/C IN connector).RGB/COMPONENT: Set to monitor the signal input through the RGB/COMPONENT connector.
e s e	When picture signals in the size of 720 × 576 (50i) (or 720 × 487 (60i)) are inputSelect 720 × 576 (or 720 × 487). This is the default setting.When 702 × 576 (or 712 × 483) is selected, all sides of the input picture are cut off by several pixels.
	When picture signals in the size of 702 × 576 (50i) (or 712 × 483 (60i)) or equivalent are inputSelect 702 × 576 (or 712 × 483).When 720 × 576 (or 720 × 487) is selected, a black border (of several pixels wide) appears around the input picture.

Scan mode image

• 5:4 • NORMAL • OVER • TALLY G - EXT SYNC - BLUE ONLY • FULL • SDI

If you use the PARALLEL REMOTE function, you need to connect cables.

For more details, see page 52.

on KEY INHIBIT menu

You can lock the setting so that they cannot be changed by an unauthorized user.

Select OFF or ON.

If you set to ON, all items are displayed in black, indicating the items are locked.

REMOTE menu

Select the PARALLEL REMOTE connector pins for which you want to change the function.

You can assign various functions to pins 1 to 4 and 6 to 8. The following lists the functions you can assign to the pins.

REMOTE

• ("-- -": No function is assigned.) • LINE • HDMI • RGB / COMP • 16:9 • 4:3

Troubleshooting

This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support.

• The display is colored in green or purple → Select the correct input from the RGB/COMP SEL setting in the SYSTEM SETTING menu (page 48).
• The unit cannot be operated → The key protection function works. Set the KEY INHIBIT setting to OFF in the KEY INHIBIT menu.

Specifications

Picture performance

LCD panel a-Si TFT Active Matrix

Picture size 21.5 type

477 × 268.5 mm

(W/H, Diagonal)

(18.7/10.5, 21.5 inches)

Resolution 1920 × 1080 dots

Viewing angle (LCD panel specifications)

(up/down/left/right, contrast > 10:1)

80°/80°/85°/85° (typical)

Scan Normal 0%

Over 5%

Aspect 16:9

Display color 16,770,000

Input/output connectors

Input

LINE input connectors

Y/C input 4-pin mini-DIN (1)

VIDEO input

BNC type (1), 1 Vp-p ±3 dB, negative

synchronization

AUDIO input

Phono jack (1), -5 dBu, 47 kilohms or

higher

RGB/COMPONENT input connectors

BNC (3)

RGB input 0.7 Vp-p ±3 dB, (Sync On Green,

0.3 Vp-p negative sync.)

Component input

0.7 Vp-p ±3 dB, (75% chrominance

standard color bar signal)

AUDIO input

Phono jack (1), -5 dBu, 47 kilohms or

higher

OPTION IN connector

D-sub 9-pin (1), female

OPTION AUDIO IN connector

Phono jack (1), -5 dBu, 47 kilohms or

higher

External synchronized input connector

BNC type (1), 0.3 Vp-p to 4.0 Vp-p ±

bipolarity ternary or negative

polarity binary

HDMI IN connector

HDMI (1)

PARALLEL REMOTE input connector

Parallel remote

Modular connector 8-pin (1)

Output

LINE output connectors

Y/C output 4-pin mini-DIN (1), Loop-through, with 75 ohms automatic terminal function

VIDEO output

BNC type (1), Loop-through, with 75 ohms automatic terminal function

AUDIO output

Phono jack (1), Loop-through

RGB/COMPONENT output connectors

RGB/Component output

BNC type (3), Loop-through, with 75 ohms automatic terminal function

AUDIO output

Phono jack (1), Loop-through

External synchronized output connector

BNC type (1), Loop-through, with 75 ohms automatic terminal function

Built-in speaker output

0.5 W (mono)

General

Power AC 100 to 240 V, 50/60 Hz

Power consumption

Maximum: approx. 69 W, 1.3 A to 0.6 A

Operating conditions

Temperature

0°C to 35°C (32°F to 95°F)

Recommended temperature

20 °C to 30 °C (68 °F to 86 °F)

Humidity 30% to 85% (no condensation)

Pressure 700 hPa to 1060 hPa

Storage and transport conditions

Temperature

-20°C to +60°C (-4°F to +140°F)

Humidity 0% to 90%

Pressure 700 hPa to 1060 hPa

Accessories supplied

AC power cord (1)

AC plug holder (2)

Instructions for Use (1)

CD-ROM (1)

Using the CD-ROM Manual (1)

Quick Reference (1)

When you First Use the Monitor (1)

Sales Companies Guide (1)

Optional accessories

HD/SD-SDI input adaptor BKM-341HS

Medical Specifications

Protection against electric shock:

Class I

Protection against harmful ingress of water:

Ordinary

Degree of safety in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide:

Not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide

Mode of operation:

Continuous

Design and specifications are subject to change without notice.

Note

Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.

Pin assignment

PARALLEL REMOTE connector

Modular connector (8-pin)

Pin number Functions

1 Designating LINE input signal
2 Designating HDMI input signal
3 Designating RGB/COMPONENT input signal
4	16:9
5	GND
6	4:3
7	Selecting	NORMAL
8	Selecting	OVER

For details on function allocations, see REMOTE menu (page 50).

Wiring required to use the Remote Control

Connect the function you want to use with a Remote Control to the Ground (Pin 5).

Video signal formats

The unit is applicable to the following signal formats.

System	Total lines	Active lines	Frame rate	Scanning format	Aspect ratio	Signal standard
575/50I (PAL)	625 575 25 2:1 interlace 16:9/4:3					EBU N10(PAL: ITU-R BT.624)
480/60I (NTSC) *1	525 483 30 2:1 interlace 16:9/4:3					SMPTE 253M(NTSC: SMPTE 170M)
576/50P 625 576 50 Progressive 16:9/4:3 ITU-R BT.1358
480/60P 525 483 60 Progressive 16:9/4:3 SMPTE 293M
1080/24P *1	1125 1080 24 Progressive 16:9 SMPTE 274M
1080/25P	1125 1080 25 Progressive 16:9			SMPTE 274M
1080/30P *1	1125 1080 30 Progressive 16:9 SMPTE 274M
1080/50I	1125 1080 25 2:1 interlace		16:9 SMPTE 274M
1080/60I *1	1125	1080	30	2:1 interlace	16:9	SMPTE 274M/BTA S-001B
720/50P 750 720 50 Progressive 16:9 SMPTE 296M
720/60P *1	750 720 60 Progressive 16:9 SMPTE 296M

*1 Also supports frame rate 1/1.001.

Applicable DVI input signals

When a PC signal is input to the HDMI IN connector using a DVI conversion cable

Resolution	Dot clock (MHz)	fH (kHz)	fV (Hz)
720 × 400 70Hz	28.322	31.469	70.087
800 × 600 56Hz	36.000	35.156	56.250
800 × 600 60Hz	40.000	37.879	60.317
1024 × 768 60Hz	65.000	48.363	60.004
1280 × 1024 60Hz	108.000	63.981	60.020
1920 × 1080 50Hz	141.375	55.572	49.975
1920 × 1080 50Hz	148.500	56.250	50.000
1920 × 1080 60Hz	148.352	67.432	59.940
1920 × 1080 60Hz	138.625	66.647	59.988
1920 × 1080 60Hz	148.500	67.500	60.000

Note

The sides of the displayed picture may be invisible depending on the input signal.

When an optional input adaptor is connected, the unit is applicable to the following signal formats.

When BKM-341HS is connected

Input
System Signal standard
575/50I SMPTE 259M
480/60I*1	SMPTE 259M
1080/24PsF*1	SMPTE 292M
1080/25PsF SMPTE 292M
1080/24P*1	SMPTE 292M
1080/25P SMPTE 292M
1080/30P*1	SMPTE 292M
1080/50I SMPTE 292M
1080/60I*1	SMPTE 292M
720/50P SMPTE 292M
720/60P*1	SMPTE 292M

*1 The frame rate is also compatible with 1/1.001.

Dimensions

Front

Rear

Side

Bottom

Unit: mm (inches) Mass Approx. 8.6 kg (18 lb 15 oz)

French

Please provide with the protection cover for the connector when you do not use the specified connectors.

① HDMI IN connector

G/Y, B/PB, R/PR IN/OUT (BNC)

AUDIO IN/OUT (phono jack)

AUDIO IN/OUT (phono jack)

		TEMP COUL	NIVEAU COMPOSANT	REGLAGE NTSC
1NORTH AMERICA		BAS	BETA7.5	7.5
2LATIN AMERICA	ARGENTINA BAS SMPTE 0
PAL&PAL-N AREA	PARAGUAY BAS SMPTE 0
	URUGUAY BAS SMPTE 0
NTSC&PAL-M AREA	OTHER AREA BAS BETA7.5 7.5
3AFRICA AUSTRALASIA EUROPE MIDDLE-EAST		BAS SMPTE 0
4ASIA EXCEPT JAPAN	NTSC AREA BAS BETA7.5 7.5
	PAL AREA BAS SMPTE 0
5JAPAN		HAUT	SMPTE	0

Please provide with the protection cover for the connector when you do not use the specified connectors.

① HDMI IN connector

⑤ EXT SYNC IN/OUT connectors (external sync) (BNC)

⑥ RGB/COMPONENT connectors

G/Y, B/PB, R/PR IN/OUT (BNC)

AUDIO IN/OUT (Phono jack)

Y/C IN/OUT (4-pin, Mini-DIN)

AUDIO IN/OUT (Phono jack)

		FARB-TEMP.	KOMPONENTEN-PEGEL	NTSC-PEGEL
1NORTH AMERICA		NIEDR.	BETA7.5	7.5
2LATIN AMERICAPAL&PAL-NAREA	ARGENTINA NIEDR. SMPTE 0
	PARAGUAY NIEDR. SMPTE 0
	URUGUAY NIEDR. SMPTE 0
NTSC&PAL-MAREA	OTHER AREA NIEDR. BETA7.5 7.5
3AFRICA AUSTRALASIAEUROPE MIDDLE-EAST		NIEDR. SMPTE 0
4ASIA EXCEPTJAPAN	NTSC AREA NIEDR. BETA7.5 7.5
	PAL AREA NIEDR. SMPTE 0
5JAPAN		HOCH	SMPTE	0

Input connectors RGB/COMPONENT

BNC type (3)

RGB input

0.7 Vp-p ±3 dB, (Sync on Green,

0.3 Vp-p negative Sync)

Component input

0.7 Vp-p ±3 dB, (75% chrominance standard color bar signal)

AUDIO input

Phono jack (1), -5 dBu 47 kilohm or higher

OPTION IN connector

D-sub 9-pin (1), female

Output connectors RGB/COMPONENT