PBH 2500 SRE - Drill BOSCH - Free user manual and instructions

Brand	Bosch
Model	PBH 2500 SRE
Product Type	Hammer drill (rotary)
Power Input	750 W
Supply Voltage	230 V / 50 Hz
Maximum Impact Energy	2.2 J
No-load Speed	0 – 1100 rpm
Impact Rate	0 – 4000 impacts/min
Max. Drilling Diameter in Concrete	24 mm
Max. Drilling Diameter in Steel	13 mm
Max. Drilling Diameter in Wood	30 mm
Tool Holder	SDS-plus
Weight	2.6 kg
Dimensions (L × W × H)	370 × 75 × 210 mm
Main Functions	Drilling, hammer drilling, chiseling (Vario-Lock positions)
Settings	Variable speed, forward/reverse, mode selector
Safety Devices	Safety clutch, protective cover
Ease of Use	Auxiliary handle, depth stop, integrated bubble level
Maintenance and Cleaning	Clean with a dry cloth, grease the tool holder regularly
Spare Parts and Repairability	Carbon brushes available, Bosch after-sales service
Included Accessories	Auxiliary handle, depth stop, chisel bit, carry case
General Information	CE certification, 2-year manufacturer warranty

Frequently Asked Questions - PBH 2500 SRE BOSCH

How to change the SDS-plus chuck?

To change the SDS-plus chuck, turn the locking ring forward while pulling the bit. Then insert the new tool by pushing until it clicks. Make sure it is locked properly.

How to use the hammer mode?

Turn the mode selector to the hammer symbol. This mode is ideal for drilling in concrete or masonry. Do not use on metal or wood.

What oil to use to grease the tool holder?

Use a special grease for power tools, available from Bosch. Apply a small amount every 10,000 holes to extend the service life.

How to adjust the drilling depth?

Attach the depth stop to the auxiliary handle. Loosen the knob, adjust the rod to the desired depth, then tighten.

What to do if the drill overheats abnormally?

Immediately stop the device and let it cool down. Check that the ventilation slots are not blocked. If the problem persists, contact Bosch customer service.

Can I use SDS bits?

Yes, this tool only accepts SDS-plus bits. Standard SDS bits are not compatible.

How to maintain the carbon brushes?

The carbon brushes should be checked every 50 hours of use. If the brush is less than 5 mm long, replace both carbon brushes. Unscrew the caps, remove the worn brushes and insert the new ones.

Does the drill have built-in safety?

Yes, it is equipped with a safety clutch that disengages the drive in case of bit jamming, reducing the risk of wrist strain.

How to reverse the direction of rotation?

Use the forward/reverse switch located above the trigger. Push it to the left for clockwise rotation (drilling) and to the right for counterclockwise (unscrewing).

Where to find the full manual?

The user manual is available for free download on the site notice-facile.com or on the official Bosch website.

USER MANUAL PBH 2500 SRE BOSCH

Deutsch

Safety instructions

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

www.bosch-pt.com/serviceaddresses

Disposal

General Power Tool Safety Warnings

WARNING

Read all safety warnings, instructions, illustrations and specifications.

tions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents. ▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. ▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents. ▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. ▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Hammer Safety Warnings

Safety instructions for all operations

Wear ear protectors. Exposure to noise can cause hearing loss. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring or its own cord. Cutting accessory or fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

Safety instructions when using long drill bits with rotary hammers

Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury. Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend, causing breakage or loss of control, resulting in personal injury.

Additional safety information

▶ Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage or may cause an electric shock. ▶ Always wait until the power tool has come to a complete stop before placing it down. The application tool can jam and cause you to lose control of the power tool. - Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.

Products sold in GB only:

Your product is fitted with a BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorized customer service agent. The replacement plug should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

▶ Do not touch any application tools or adjacent housing components shortly after operation. These can become very hot during operation and cause burns. The application tool may jam during drilling. Make sure you have a stable footing and hold the power tool firmly with both hands. Otherwise you could lose control of the power tool. ▶ Take care when carrying out demolition work using the chisel. Falling fragments of the demolition material could injure you or any bystanders.

Product Description and Specifications

Read all the safety and general instructions. Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.

Please observe the illustrations at the beginning of this operating manual.

Intended Use

The power tool is intended for hammer drilling in concrete, brick and stone, as well as for light chiselling work. It is also suitable for drilling without impact in wood, metal, ceramic and plastic. Power tools with electronic control and right/left rotation are also suitable for screwdriving.

Product Features

The numbering of the product features refers to the diagram of the power tool on the graphics page.

(1) Keyless chuck (PBH 2500 SRE) a) (2) SDS plus drill chuck (3) SDS plus tool holder (4) Dust protection cap (5) Locking sleeve (6) Handle (insulated gripping surface) (7) Rotational direction switch (8) Lock-on button for on/off switch (9) On/off switch (10) Impact/mode selector switch (11) Button for depth stop adjustment (12) Wing bolt of auxiliary handle (13) Auxiliary handle (insulated gripping surface) (14) Depth stop (15) Securing screw for keyed chuck 4 (16) Keyed chuck (PBH 2100 SRE, PBH 2500 SRE) a) (17) SDS plus shank for drill chuck a) (18) Saugfix suction opening a) (19) Saugfix clamping screw 4 (20) Saugfix depth stop 4 (21) Saugfix telescopic tube a) (22) Saugfix wing bolt a) (23) Saugfix guide tube a) (24) Universal holder with SDS plus shank a)

a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.

Technical Data

Rotary hammer PBH 2000 RE		PBH 2100 SRE PBH 2500 RE PBH 2500 SRE
		PBH 2100 RE
Article number		3 603 CA9 3..	3 603 CA9 3..	3 603 B44 4..	3 603 B44 4..
Keyed chuck - ● - ●
Keyless chuck - - - ●					A)
Rated power input W 550 550 600 600
Impact rate min	-1	4600	4600	5100	5100
Impact energy per stroke according to EPTA-Procedure 05:2016	J 1.7	1.7	1.9	1.9
No-load speed	min-1	0-2400	0-2400	0-2600	0-2600
Tool holder		SDS plus	SDS plus	SDS plus	SDS plus
Spindle collar diameter	mm	43	43	43	43
Max. drilling diameter
- Concrete	mm	20	20	22	22
- Steel	mm	13	13	13	13

16 | English

Rotary hammer PBH 2000 RE	PBH 2100 SRE PBH 2500 RE PBH 2500 SRE
	PBH 2100 RE
- Wood mm 30 30 30 30
Weight according to EPTA-Procedure 01:2014	kg 2.2 2.2 2.2 2.2
Protection class	☐ /II /II /II /II	☐

A) This accessory is not available in every country. The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

	PBH 2000 REPBH 2100 RE	PBH 2100 SRE PBH 2500 REPBH 2500 SRE
Noise emission values determined according to EN 62841-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level dB(A)	91 91 94 94
Sound power level dB(A)	102 102 105 105
Uncertainty K dB	3 3 3 3
Wear hearing protection!
Vibration total values ah(triax vector sum) and uncertainty K determined according to EN 62841-2-6:
Hammer drilling into concrete:
ah	m/s2	16.0 16.0 16.0 16.0
K m/s	2	1.5 1.5 1.5 1.5
Chiselling:
ah	m/s2	12.5 12.5 12.0 12.0
K m/s	2	1.5 1.5 1.5 1.5

The vibration level and noise emission value given in these instructions have been measured in accordance with a standardised measuring procedure and may be used to compare power tools. They may also be used for a preliminary estimation of vibration and noise emissions.

The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different application tools or is poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total working period.

To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account. This may significantly reduce vibration and noise emissions over the total working period.

Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and application tools, keeping their hands warm, and organising workflows correctly.

Assembly

Pull the plug out of the socket before carrying out any work on the power tool.

Auxiliary handle

Do not operate your power tool without the auxiliary handle (13). Make sure that the auxiliary handle is always tightened. Otherwise you could lose control of the power tool when working.

Swivelling the auxiliary handle (see figure A)

You can swivel the auxiliary handle (13) to any angle for a safe work posture that minimises fatigue.

- Loosen the wing bolt (12) of the auxiliary handle (13) and adjust the auxiliary handle (13) to the required position. Then retighten the wing bolt (12) of the auxiliary handle (13). Make sure that the clamping ring of the auxiliary handle slots into the corresponding groove on the housing.

Selecting drill chucks and tools

Hammer drilling and chiselling require SDS-plus application tools that are inserted into the SDS-plus drill chuck.

For drilling without impact in wood, metal, ceramic and plastic as well as for screwdriving, tools without SDS-plus are used (e.g. cylindrical shank drill bits). For these tools, a keyless chuck or a keyed chuck are required.

Changing the drill chuck

Inserting/removing the keyed chuck

PBH 2100 SRE/PBH 2500 SRE

You must use a suitable drill chuck (keyed or keyless chuck, accessories) to work with tools that do not have SDS-plus (e.g. cylindrical shank drill bits).

Fitting the keyed chuck (see figure B)

- Screw the SDS-plus shank (17) into a keyed chuck (16). Secure the keyed chuck (16) using the securing screw (15). Note that the securing screw has a left-hand thread.

Inserting the keyed chuck (see figure B)

– Clean and lightly grease the insertion end of the shank. - Insert the keyed chuck with the adapter shank into the tool holder with a turning motion until it automatically locks. - Check that it is locked by pulling the keyed chuck.

Removing the keyed chuck

- Push the locking sleeve (5) back and remove the keyed chuck (16).

Inserting/Removing the Keyless Chuck

PBH 2500 SRE

Inserting the keyless chuck (see figure C)

• Clean and lightly grease the insertion end of the shank.
• Insert the keyless chuck (1) with the shank into the tool holder while turning it until it locks automatically.
• Check that it is locked by pulling the keyless chuck.

Removing the Keyless Chuck

- Push the locking sleeve (5) back and remove the keyless chuck (1).

Changing the Tool

The dust protection cap (4) largely prevents the penetration of drilling dust into the tool holder during operation. When inserting the tool, make sure that the dust protection cap (4) does not become damaged.

Replace a damaged dust protection cap immediately. It is recommended that you have use an after-sales service for this.

Changing the tool (SDS plus)

Inserting SDS-plus application tools (see figure D)

The SDS-plus drill chuck enables you to change the application tool easily and conveniently without needing to use additional tools.

- Clean and lightly grease the insertion end of the application tool.

• Insert the application tool into the tool holder while turning it until it locks automatically.
• Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus application tool can move freely. This causes a certain radial run-out at no-load, which has no effect on the accuracy of the drill hole, as the drill bit centres itself upon drilling.

Removing SDS-plus application tools (see figure E)

- Push the locking sleeve (5) back and remove the application tool.

Changing the keyed chuck

PBH 2100 SRE/PBH 2500 SRE

Inserting the application tool

Note: Application tools that do not have SDS plus must not be used for hammer drilling or chiselling. Tools without SDS plus and their drill chucks are damaged by hammer drilling or chiselling.

• Insert a keyed chuck (16).
• Open the keyed chuck (16) by turning it until the tool can be inserted. Insert the tool.
• Insert the chuck key into the corresponding holes of the keyed chuck (16) and clamp the tool evenly.
• Turn the impact/mode selector switch (10) to the "drilling" position.

Removing the application tool

- Use the chuck key to turn the sleeve of the keyed chuck (16) anticlockwise until the application tool can be removed.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of wood, minerals, and metal can be harmful to human health. Touching or breathing in this dust can trigger allergic reactions and/or cause respiratory illnesses in the user or in people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as carcinogenic, especially in conjunction with wood treatment additives (chromate, wood preservative). Materials containing asbestos may only be machined by specialists.

• Use a dust extraction system that is suitable for the material wherever possible.
• Provide good ventilation at the workplace.
• It is advisable to wear a P2 filter class breathing mask. The regulations on the material being machined that apply in the country of use must be observed.
• Avoid dust accumulation at the workplace. Dust can easily ignite.

Dust extraction with the dust extraction attachment (accessory)

Fitting the dust extraction attachment (see figure F)

For dust extraction, the dust extraction attachment (accessory) is required. When drilling, the dust extraction attachment retracts so that the attachment head is always close to the surface at the drill hole.

• Press the button for depth stop adjustment (11) and remove the depth stop (14). Press the button (11) again and insert the dust extraction attachment into the auxiliary handle (13) from the front.
• Connect an extraction hose (diameter 19 mm, accessory) to the suction opening (18) of the dust extraction attachment.

The dust extractor must be suitable for the material being worked.

When extracting dust that is dry, especially detrimental to health or carcinogenic, use a special dust extractor.

Setting the drilling depth on the dust extraction attachment (see figure G)

You can also set the required drilling depth X when the dust extraction attachment is fitted.

• Push the SDS-plus application tool into the SDS-plus tool holder (3) as far as it will go. Otherwise, the movability of the SDS-plus drilling tool can lead to incorrect adjustment of the drilling depth.
• Loosen the wing bolt (22) on the dust extraction attachment.
• Without switching it on, press the power tool firmly against the surface you wish to drill. The SDS-plus application tool must be touching the surface.
• Position the guide tube (23) of the dust extraction attachment in its holder such that the head of the dust extraction attachment rests on the surface to be drilled. Do not slide the guide tube (23) further than necessary over the telescopic tube (21), so that as much as possible of the scale remains visible on the telescopic tube (21).
• Retighten the wing bolt (22). Loosen the clamping screw (19) on the depth stop of the dust extraction attachment.
• Slide the depth stop (20) onto the telescopic tube (21) so that the distance X shown in the illustration matches your required drilling depth.
• Tighten the clamping screw (19) in this position.

Operation

▶ Products that are only sold in AUS and NZ: Use a residual current device (RCD) with a nominal residual current of 30 mA or less.

Start-up

Pay attention to the mains voltage! The voltage of the power source must match the voltage specified on the rating plate of the power tool. Power tools marked with 230 V can also be operated with 220 V.

Setting the Operating Mode

The operating mode of the power tool is selected using the impact/mode selector switch (10).

- To change the operating mode, turn the impact/mode selector switch (10) to the required position.

Note: Only change the operating mode when the power tool is switched off. Otherwise, the power tool may become damaged.

Position for hammer drilling into concrete or stone

Position for drilling without impact in wood, metal, ceramic and plastic and for screw-driving

Vario-Lock position for adjusting the chisel position. The impact/mode selector switch (10) will not engage in this position.

Position for chiselling

Setting the rotational direction (see figure H)

The rotational direction switch (7) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (9) is being pressed.

Only operate the rotational direction switch (7) when the power tool is not in use.

Always set the rotational direction to clockwise rotation for hammer drilling, drilling and chiselling.

• Clockwise: To drill and to drive in screws, press the rotational direction switch (7) all the way to the left.
• Anticlockwise: To loosen and unscrew screws and nuts, press the rotational direction switch (7) all the way to the right.

Switching On/Off

• To switch on the power tool, press the on/off switch (9).
• To lock the on/off switch (9), press and hold it while also pushing the lock-on button (8).
• To switch off the power tool, release the on/off switch (9). If the on/off switch (9) is locked, press the switch first and then release it.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when it is on by pressing in the on/off switch (9) to varying extents.

Applying light pressure to the on/off switch (9) results in a low rotational speed/impact rate. Applying increasing pressure to the switch increases the speed/impact rate.

Changing the chiselling position (Vario-Lock)

You can lock the chisel in 36 different positions, so you can select the optimum working position for each task.

- Insert the chisel into the tool holder.

• Turn the impact/mode selector switch (10) to the "Vario-Lock" position.
• Turn the application tool to the required chisel position.
• Turn the impact/mode selector switch (10) to the "chiselling" position. With this, the tool holder is locked.
• Set the rotational direction for chiselling to clockwise.

Practical Advice

Setting the drilling depth (see figure I)

You can use the depth stop (14) to set the required drilling depth X.

• Press the button for depth stop adjustment (11) and insert the depth stop into the auxiliary handle (13). The fluting on the depth stop (14) must face downwards.
• Insert the SDS-plus application tool into the SDS-plus tool holder (3) until it stops. Otherwise, the movability of the SDS-plus drilling tool can lead to incorrect adjustment of the drilling depth.
• Pull the depth stop far enough out so that the distance between the drill bit tip and the edge of the depth stop corresponds to the required drilling depth X.

Overload clutch

If the application tool jams or snags, the power transmission to the drill spindle will be interrupted. Always hold the power tool firmly with both hands to withstand the forces this may create and adopt a position with stable footing. ▶ Switch the power tool off immediately and remove the application tool if the power tool becomes blocked. Switching on when the drilling tool is blocked may cause high torque reactions.

Inserting screwdriver bits (see figure J)

▶ Only apply the power tool to the screw/nut when the tool is switched off. Rotating tool inserts can slip off.

A universal holder (24) with SDS-plus shank (accessory) is required to work with screwdriver bits.

• Clean and lightly grease the insertion end of the shank.
• Insert the universal holder into the tool holder while turning it until it locks automatically.
• Check that it is locked by pulling the universal holder.
• Insert a screwdriver bit in the universal holder. Only use screwdriver bits that fit the screw head.
• To remove the universal holder, slide the locking sleeve (5) backwards and remove the universal holder (24) from the tool holder.

Maintenance and Service

Maintenance and Cleaning

▶ Pull the plug out of the socket before carrying out any work on the power tool. ▶ To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord needs to be replaced, this must be done by Bosch or by an after-sales service centre that is authorised to repair Bosch power tools.

Replace a damaged dust protection cap immediately. It is recommended that you use an after-sales service for this. Clean the tool holder (3) after each use.

After-Sales Service and Application Service

Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.

In all correspondence and spare parts orders, please always include the 10-digit article number given on the nameplate of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham Uxbridge

UB 95HJ

At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.

Tel. Service: [phone]

E-Mail: [e-mail]

You can find further service addresses at:

www.bosch-pt.com/serviceaddresses

Disposal

The power tool, accessories and packaging should be recycled in an environmentally friendly manner.

Do not dispose of power tools along with household waste.

Only for EU countries:

According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its implementation into national law, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom:

According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended), products

that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

Robert Bosch (France) S.A.S.

www.bosch-pt.com/serviceaddresses

PBH 2100 SRE/PBH 2500 SRE

Mounting the tool

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

Bosch Service Center

Telegrafvej 3

2750 Ballerup

At www.bosch-pt.dk, spare parts can be ordered online or a repair order can be created.

Service Center phone: [phone]

Fax: [phone]

E-Mail: [e-mail]

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

Bosch Service Center

Telegrafvej 3

2750 Ballerup

Denmark

Tel.: [phone] (within Sweden)

Fax: [phone]

www.bosch-pt.com/serviceaddresses

Waste disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

Position for chiseling

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

PBH 2100 SRE/PBH 2500 SRE

Mounting the tool

www.bosch-pt.com/serviceaddresses

Disposal

PBH 2100 SRE/PBH 2500 SRE

Mounting the tool

PBH 2100 SRE/PBH 2500 SRE

To be able to use the tool without SDS-plus

www.bosch-pt.com/serviceaddresses

1 607 000 173

1 618 580 000

SDS-plus

1618571014

∅ 2.5 - 13 mm

1607950045

2 607 000 207

CE

1

de	EU-Konformitätserklärung		Wir erklären in alleiniger Verantwortung, dass die genannten Produkte allen einschlägigen Bestimmungen der nachfolgend aufgeführten Richtlinien und Verordnungen entsprechen und mit folgenden Normen übereinstimmen.Technische Unterlagen bei:*
	Bohrhammer	Sachnummer
en	EU Declaration of Conformity		We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.Technical file at:*
	Rotary Hammer	Article number
fr	Déclaration de conformité UE		Nous déclarons sous notre propre responsabilité que les produits décrits sont en conformité avec les directives, règlements normatifs et normes énumérés ci-dessous.Dossier technique auprès de:*
	Marteau perforateur	N° d'article
es	Declaración de conformidad UE		Declaramos bajo nuestra exclusiva responsabilidad, que los productos nombrados cumplen con todas las disposiciones correspondientes de las Directivas y los Reglamentos mencionados a continuación y están en conformidad con las siguientes normas.Documentos técnicos de:*
	Martillo perforador	N° de artículo
pt	Declaração de Conformidade UE		Declaramos sob nossa exclusiva responsabilidade que os produtos mencionados cumprem todas as disposições e os regulamentos indicados e estão em conformidade com as seguintes normas.Documentação técnica pertencente à:*
	Martelo perfurador	N.° do produto
it	Dichiarazione di conformità UE		Dichiariamo sotto la nostra piena responsabilità che i prodotti indicati sono conformi a tutte le disposizioni pertinenti delle Direttive e dei Regolamenti elencati di seguito, nonché alle seguenti Normative.Documentazione Tecnica presso:*
	Martello perforatore	Codice prodotto
nl	EU-conformiteitsverklaring		Wij verklaren op eigen verantwoordelijkheid dat de genoemde producten voldoen aan alle desbetreffende bepalingen van de hierna genoemde richtlijnen en verordeningen en overeenstemmen met de volgende normen.Technisch dossier bij:*
	Boorhamer	Productnummer
da	EU-overensstemmelseserklæring		Vi erklærer som eneansvarlige, at det beskrevne produkt er i overensstemmelse med alle gældende bestemmelser i følgende direktiver og forordninger og opfylder følgende standarder.Tekniske bilag ved:*
	Borehammer	Typenummer
sv	EU-konformitetsförklaring		Vi förklarar under eget ansvar att de nämnda produkterna uppfyller kraven i alla gällande bestämmelser i de nedan angivna direktiven och förordningarnas och att de stämmer överens med följande normer.Teknisk dokumentation:*
	Borrhammare	Produktnummer
no	EU-samsvarserklæring		Vi erklærer under eneansvar at de nevnte produktene er i overensstemmelse med alle relevante bestemmelser i direktivene og forordningene nedenfor og med følgende standarder.Teknisk dokumentasjon hos:*
	Borhammer	Produktnummer
fi	EU-vaatimustenmukaisuusvakuutus		Vakuutamme täten, että mainitut tuotteet vastaavat kaikkia seuraavien direktiivien ja asetusten asiaankuuluvia vaatimuksia ja ovat seuraavien standardien vaatimusten mukaisia.Tekniset asiakirjat saatavana:*
	Poravasara	Tuotenumero
el	Δήλωση πιστότητας ΕΕ		Δηλώνουμε με αποκλειστική μας ευθύνη, ότι τα αναφερόμενα προϊόντα αντιστοιχούν σε όλες τις σχετικές διατάξεις των πιο κάτω αναφερόμενων οδηγιών και κανονισμών και ταυτίζονται με τα ακόλουθα πρότυπα.Tεχνικά έγγραφα στη:*
	Περιστροφικό πιστολέτο	Αριθμός ευρετηρίου
tr	AB Uygunluk beyani		Tek sorumlu olarak, tanımlanan ürünün aşağıdaki yönetmelik ve direktiflerin geçerli bütün hükümlerine ve aşağıdaki standartlara uygun olduğunu beyan ederiz.Teknik belgelerin bulunduğu yer:*
	Kırıcı-delici	Ürün kodu

||

CE

pl	Deklaracja zgodności UE		Oświadczamy z pełną odpowiedzialnością, że niniejsze produkty odpowiadają wszystkim wymaganiom poniżej wyszczególnionych dyrektyw i rozporządzeń, oraz że są zgodne z następującymi normami.Dokumentacja techniczna:*
	Młot udarowo-obrotowy	Numer katalogowy
cs	EU prohlásení oshodě		Prohlašujeme na výhradní zodpovědnost, že uvedený výrobek splňuje všechna příslušná ustanovení níže uvedených směrnic anařizení aje vsouladu snásledujícími normami:Technické podklady u:*
	Vrtací kladivo	Objednací číslo
sk	EÚ vyhlásenie ozhode		Vyhlasujeme na výhradní zodpovednosť, že uvedený výrobok splňa všetky príslušné ustanovenia nižšie uvedených smerníc anariadení aje vsúlade snasledujúcimi normami:Technické podklady má spoločnosť:*
	Vrtacie kladivo	Vecné číslo
hu	EU konformitási nyilatkozat		Egyedüli felelőséggel kijelentjük, hogy a megnevezett termékek megfelelnek az alábbiakban felsorolásra kerülő irányelvek és rendeletek valamennyi idevágó előírásainak és megfelelnek a következő szabványoknak.Műszaki dokumentumok megőrzési pontja:*
	Fúrókalapács	Cikkszám
ru	Заявление о соответствии EC		Мы заявляем под нашу единоличную ответственность, что названные продукты соответствуют всем действующим предписаниям нижеуказанных директив и распоряжений, а также нижеуказанных норм.Техническая документация хранится y:*
	Перфоратор	Tоварный No
uk	Заява про відповідність ЄС		Мизаявляемо під нашу одноособову відповідальність, що названі вироби відповідають усім чинним положенням нищеозначених директив і розпоряджень, а також нижчеозначеним нормам.Технічна документація зберігається y:*
	Перфоратор	Tоварний номер
kk	EO сәйкестік мағлумдамасы		Өз жауапкершілікпен біз аталған өнімдер төменде жзылған директикалар мен жарлықтардың тиісті қағилаларына сәйкестігін және төмендегі нормаларға сай екенін білдіреміз.Техникалық құжаттар:*
	Перфоратор	Өнім нөмірі
ro	Declarație de conformitate UE		Declarăm pe proprie răspundere că produsele mentionate corespund tuturor dispozițiilor relevante ale directivelor și reglementărilor enumerate în cele ce urmează și sunt în conformitate cu următoarele standarde.Documentаție tehnică la:*
	Ciocan rotopercutor	Număr de identificare
bg	EC декларация за съответствие		С пълна отговорност ние декларираме, че посочените продукти отговарят на всички валидни изисквания на директивите и разпоредбите по-долу и съответства на следните стандарти.Техническа документация при:*
	Перфоратор	Каталожен номер
mk	EU-Изјава за сообразност		Со целосна одговорност изјавуваме, дека опишаните производи се во согласност со сите релевантни одредби на следните регулативи и прописи и се во согласност со следните норми.Техничка документација кaj:*
	Чекани за дупчење	Број на дел/артик
sr	EU-izjava o usaglašenosti		Na sopstvenu odgovornost izjavljujemo, da navedeni proizvodi odgovaraju svim dotičnim odredbama naknadno navedenih smernica u uredaba i da su u skladu sa sledećim standardima.Tehnička dokumentacija kod:*
	Bušilica čekić	Broj predmeta
sl	Izjava o skladnosti EU		Izjavljamo pod izključno odgovornostjo, da je omenjen izdelek v skladu z vsemi relevantnimi določili direktiv in uredb ter ustreza naslednjim standardom.Tehnična dokumentacija pri:*
	Vrtalno kladivo	Številka artikla
hr	EU izjava o sukladnosti		Pod punom odgovornošću izjavljujemo da navedeni proizvodi odgovaraju svim relevantnim odredbama direktiva i propisima navedenima u nastavku i da su sukladni sa sljedećim normama.Tehnička dokumentacija se može dobiti kod:*
	Udarna bušilica	Kataloški br.

CE III

et	EL-vastavusdeklaratsioon		Kinnitame ainuvastutajatena, et nimetatud tooted vastavad järgnevalt loetletud direktiivide ja määruste köikidele asjaomastele nõuetele ja on kooskõlas järgmiste normidega.Tehnilised dokumendid saadaval: *
	Puurvasar	Tootenumber
lv	Deklarácija par atbilstibuES standartiem		Mēs ar pilnu atbildibu paziņojam, ka šeit aplūkotie izstrādājumi atbilst visiem tālāk minētajās direktivās un rikojumos ietvertajām saistošajām nostādnēm,kā arī sekojošiem standartiem.Tehniskā dokumentācija no: *
	Perforators	Izstrādājuma numurs
lt	ES atitikties deklaracija		Atsakingai pareiškiame, kad išvardyti gaminiai atitinka visus privalomusžemiau nurodytų direktyvų ir reglamentų reikalavimus ir šiuos standartus.Techninė dokumentacija saugoma: *
	Perforatorius	Gaminio numeris
	PBH 2000 RE	3 603 CA9 322	2006/42/EC	EN 62841-1:2015
	PBH 2100 RE	3 603 CA9 300	2014/30/EU	EN IEC 62841-2-6:2020+A11:2020
	PBH 2100 RE	3 603 CA9 320	2011/65/EU	EN IEC 55014-1:2021
	PBH 2100 RE	3 603 CA9 350		EN IEC 55014-2:2021
	PBH 2100 RE	3 603 CA9 330		EN IEC 61000-3-2:2019+A1:2021
	PBH 2100 RE	3 603 CA9 370		EN 61000-3-3:2013+A1:2019+A2:2021
	PBH 2100 RE	1 600 A02 18Y		EN IEC 63000:2018
	PBH 2100 SRE	3 603 CA9 321	BOSCH	*Robert Bosch Power Tools GmbH(PT/ECS)70538 StuttgartGERMANY
	PBH 2100 SRE	3 603 CA9 301
	PBH 2500 RE	3 603 B44 401
	PBH 2500 RE	3 603 B44 421
	PBH 2500 SRE	3 603 B44 404	Henk BeckerChairman ofExecutive Management	Helmut HeinzelmannHead of Product Certification
	PBH 2500 SRE	3 603 B44 400
			Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANYStuttgart, 12.01.2023

IV

CE

Declaration of Conformity

Rotary Hammer Article number

PBH 2100 RE 3 603 CA9 370

We declare under our sole responsibility that the stated products comply with all applicable provisions of the regulations listed below and are in conformity with the following standards.

Technical file at: Robert Bosch Ltd. (PT/SOP-GB), Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom

The Supply of Machinery (Safety) Regulations 2008

The Electromagnetic Compatibility Regulations 2016

The Restriction of the Use of Certain Hazardous Substances in

Electrical and Electronic Equipment Regulations 2012

EN 62841-1:2015

EN IEC 62841-2-6:2020+A11:2020

EN IEC 55014-1:2021

EN IEC 55014-2:2021

EN IEC 61000-3-2:2019+A1:2021

EN 61000-3-3:2013+A1:2019+A2:2021

EN IEC 63000:2018

BOSCH

Vonjy Rajakoba

Managing Director - Bosch UK

Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany represented (in terms of the above regulations) by

Robert Bosch Limited, Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom

Martin Sibley

Head of Sales Operations and Aftersales

Robert Bosch Ltd. Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom, as authorised representative acting on behalf of Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany

Place of issue: Uxbridge Date of issue: 12/01/2023