Excelon CA-PLT14SG3 - Hand blender KENWOOD - Free user manual and instructions

Product Type	Hand Blender (Immersion Blender)
Brand	Kenwood
Model	Excelon CA-PLT14SG3
Power	800 W
Speed Settings	20 variable speeds
Blending Shaft Material	Stainless steel
Motor Unit Material	Plastic with soft-grip handle
Beaker Capacity	1.0 L (included)
Whisk Attachment	Yes, included
Chopper Attachment	500 mL chopper bowl included
Cord Length	1.5 m
Weight	1.2 kg
Dimensions (L x W x H)	40 x 10 x 12 cm
Dishwasher Safe Parts	Blending shaft, beaker, whisk, chopper bowl
Safety Features	Overheat protection, non-slip base
Warranty	2 years

Frequently Asked Questions - Excelon CA-PLT14SG3 KENWOOD

How do I clean the blending shaft?

Rinse the shaft under running water immediately after use. For stubborn residue, use a mild detergent. The shaft is dishwasher safe.

Can I blend hot liquids?

Yes, but allow liquids to cool slightly to avoid splashing. Do not immerse the motor unit in liquid.

What is the power consumption?

The Kenwood Excelon CA-PLT14SG3 has a power rating of 800 W.

Is the whisk attachment suitable for whipping cream?

Yes, the whisk is designed for whipping cream, egg whites, and light batters. Use a wide container for best results.

How do I use the chopper attachment?

Attach the chopper bowl to the motor unit, add ingredients, and pulse using the turbo function for fine chopping.

What is the warranty period?

The hand blender comes with a 2-year warranty against manufacturing defects.

Can I use the blender without the beaker?

Yes, you can use any suitable container. Ensure the blending shaft is fully submerged.

How do I prevent splashing?

Start blending at a low speed and gradually increase. Keep the blending head submerged and use a deep container.

Are spare parts available?

Yes, replacement blending shafts, whisks, and chopper bowls can be ordered from Kenwood or authorized dealers.

What does the turbo function do?

The turbo function provides maximum power for tough blending tasks. Press and hold the turbo button to engage.

USER MANUAL Excelon CA-PLT14SG3 KENWOOD

Installation procedure

1. With your ignition switch in the "OFF" position, remove your outer fairing/headlamp assembly and set it aside. Refer to a service manual if you need help with this.

NOTE: Placing a towel on the front fender can help prevent scratches or "dings" from dropped tools or fasteners, etc.

1. Clutch Side Speaker Cabinet Removal: The images below show the 8 fasteners that will need to be removed to allow the clutch side cabinet to be removed from the bike. If your bike has the CB module, (mounted "sideways" on the clutch side cabinet), undo the antenna cable and main harness. The CB module will stay attached to the clutch side cabinet when removed. Undo the speaker wire plugs going into the cabinet (pink & pink with black stripe wires). If your bike had the CB Module, remove its mounting plate from the speaker cabinet.

Figure 1.1 - Side View of Cabinet Figure 1.2 - Back View of Cabinet

1. Attaching the Main Plate to the Speaker Cabinet: On the side of the cabinet, you will see a threaded insert and a locating post as seen in Fig 1.3. Put the main plate on the cabinet so one of the holes in the plate goes over the locating post, and the other sits over the threaded insert. If you removed a CB module from an Ultra, you can use the screw that secured that module to the speaker pod. If your bike did not have a CB module, use the machine screw that came in the kit to secure the side plate to the speaker cabinet. Fig 1.3 on the next page shows the plate correctly placed on the speaker cabinet.

2. Preparing the Plate for the Amp: The kit comes with self-adhesive "hook and loop" material. Separate this so you have 2 pieces. If your amplifier does not already have hook and loop material applied, one of the pieces will be applied to the underside of the amp. Making sure you use the opposite material to what is on the underside of the amp (refer to Fig 1.3). cut the remaining piece of hook and loop material so you have 2 smaller pieces close to the size of the metal areas highlighted by white rectangles. Apply the pieces just cut to the correct sections on the plate.

3. Attaching the Amplifier to the Plate: If you are installing a KENWOOD XM160-2, the amp will "stick" to the plate as shown (see the white circle in Fig 1.4). The "top" and left "end" of the amp must be flush to the "top" and left "end" of the plate or the amp will not fit.

NOTE: It is CRITICAL that the "amplified pigtail" of the amp be on the speaker side of the cabinet as shown in Fig 1.4. In the kit is a 14" long "zip tie" which will wrap around the plate and around the amp. Tighten the "zip tie" so it's snug only. The zip tie is on there as a backup in the unlikely event the hook and loop adhesive fails.

Figure 1.3 - Plate Correctly Placed Figure 1.4 - Amp Correctly Placed

1. Placing the Amp and Cabinet into the Bike: As shown in Fig 1.4, the "amplified pigtail" on the amp needs to be positioned over the top of the amp. If you do not do this now, you will not have access to this plug when wiring the amp. The cabinet/amplifier assembly will now go in the bike as one unit. Some "finesse" will need to be shown, but this will go without forcing anything. With the cabinet assembly in place, reinstall all 8 fasteners and secure the speaker cabinet to the bike and then proceed with wiring the amplifier.

Important Notes

©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon® are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle® and Tour-Pak® are trademarks or registered trademarks of Harley-Davidson, Inc. and/or its affiliates and if used or implied are for reference only. There is no affiliation between Harley-Davidson, Inc. and/or its affiliates and JVCKENWOOD Corporation and/or its affiliates. All other trademarks are the property of their respective owners. Specifications subject to change without notice.

For updated information (the latest Instruction Manual, etc.), please visit the following website:

https://manual.kenwood.com/en_contents/search/